versa IUI-SOL- VT5 Series User manual
Contents
2 -Contents
3- Quick Guide
4 - Arm & Disarm
5 -Stay Arm & Disarm
6- Changing user codes& Setting Date/ Time
6 - Bypassing Zones & Output Control
7- History/Memory
7 - Faults
pg 02
Quick Guide pg 03
Arming your system:
Press the 'ARM' button located on your home screen enter your code, this will start the exit
delay.
Disarming your system:
Press on the red armed icon on your display, then type your code followed by the 'Enter'
button.
Stay arming your system:
Press the button labelled ‘A1’ located on your home screen, press stay followed by your user
code and this will start the stay mode exit delay.
Disarming stay mode on your system:
Press on the armed icon on your display, then type your code followed by the 'Enter' button.
System faults:
Press ‘keypad’ then hold the number ‘5', the Keypad will then display any current faults.
History:
Press ‘keypad’ then type your code followed by '8’ & enter, the Keypad will then sequence
through the history (256 events)
Zone bypass / Sensor disable:
Press on ‘settings’ followed by ‘Zone Bypass”. This will bring up a list of your sensors. Tick
the sensor you'd like to disable. Exit and Arm your system.
Arm/Disarm pg 04
The arm functions are configured in installer programming and can relate to
up to 2 independant areas. Each system will differ relating to how your installer has
configured the system. The instructions on this page are based on your code being
assigned to one area only.
Arming your system:
Press the 'ARM' button located on your home screen then enter your code, this will start the exit delay.
Disarming your system:
Press on the red armed icon on your display, then type your code followed by the 'Enter'
button.
Stay Arm/Disarm pg 05
Stay Arm is designed for arming part of a premises while you are occupying another.
I.e. Arming the lower level of a house but not the upstairs bedrooms. arming a
separate garage & not the house.
Your installer can program the security system to have any sensor in any of the areas
to be stay (part arm) or arm (full arm) to suit your specific requirements.
Contact your installer for further information & custom stay programming
Stay arming your system:
Press the button labelled ‘A1’ located on your home screen, press stay followed by your user code and this
will start the stay mode exit delay.
Disarming stay mode on your system:
Press on the armed icon on your display, then type your code followed by the 'Enter' button.
Custom Stay Programming:
Stay arm requirements differ in almost every application and therefore requires
special programming by a security installer.
Programming pg 06
Adding/Changing User Codes:
- Press 'Settings' then ‘Users’ followed by your master user code
- Select ‘Pin” of the user you would like to alter then press # (Enter >) to save.
- Once complete , press the back button two times to return to the home screen.
Time & Date:
- Press 'Settings' then ‘Time & Date’' followed by your master user code
- From this menu you will need to set the current Time & Date
followed by 'Enter'.
- Once complete, press the back button two times to return to the home screen.
Bypassing Isolating Zones:
- Press 'Settings' then ‘Zone Bypass’' followed by your master user code
- Tick the zone you wish to bypass
-- Exit and Arm System as normal
*Bypassing a zone means that you will be able to move in the zone while the system is
armed. This procedure is automatically cleared after a single arm & disarm of the system
System Faults/ Memory pg 07
If a fault arrises within the system, your keypad will beep and will see it displayed in the right.
- Press ‘Keypad' followed by a 2 second hold of the number ‘5’ to see the full fault
description for all current system faults.
History/Memory
The security system stores up to 256 history events in a memory
buffer for recall purposes. When the buffer is full the system will start to write over
the events from old to new..
Each history event includes a time/date stamp Sallows you to recall the following:
- Who armed the system
- Who disarmed the system
- Sensor activations
- Which programmed doors were entered
- Mains power failures
- Back up battery failures
-Press ‘keypad’, type your master code followed by '8’ & enter to access this function
This manual suits for next models
2
Table of contents
