Vertex Standard EVX-R70 User manual

Digital two-way RaDio SyStem
EVX-R70 Repeater
InstallatIon GuIde
Vertex Standard LMR, Inc.

table of ContentS
Foreword ............................................................................................................................................................1
Product Safety and RF Exposure Compliance..............................................................................................1
Manual Revisions ..........................................................................................................................................1
Computer Software Copyrights .....................................................................................................................1
Document Copyrights....................................................................................................................................1
Disclaimer .....................................................................................................................................................1
Trademarks ...................................................................................................................................................1
Installation Requirements for Compliance with Radio Frequency (RF) Energy Exposure Safety Standards ....2
Declaration of Conformity...................................................................................................................................3
Product Safety and RF Exposure.......................................................................................................................4
Chapter 1 Pre-Installation Considerations..........................................................................................................8
1.1 Installation Overview ..............................................................................................................................8
1.2 Environmental Conditions at Intended Installation Site..........................................................................8
1.2.1 Operating Temperature Range.....................................................................................................8
1.2.2 Humidity .......................................................................................................................................8
1.2.3 Air Quality ....................................................................................................................................8
1.3 Equipment Ventilation ............................................................................................................................9
1.4 AC Input Power Requirements...............................................................................................................9
1.4.1 Circuit Overloading ......................................................................................................................9
1.5 Equipment Mounting Methods ...............................................................................................................9
1.6 Site Grounding and Lightning Protection ...............................................................................................9
1.6.1 Electrical Ground .........................................................................................................................9
1.6.2 RF Ground ...................................................................................................................................9
1.6.3 Lightning Ground .......................................................................................................................10
1.6.4 Equipment Ground.....................................................................................................................10
Chapter 2 Mechanical Installation .................................................................................................................... 11
2.1 Unpacking Equipment .......................................................................................................................... 11
2.2 Transferring Equipment from Shipping Container to Rack or Cabinet ................................................. 11
Chapter 3 Indicators and Connectors...............................................................................................................12
3.1 Front Panel...........................................................................................................................................12
3.1.1 LED Indicator Descriptions ........................................................................................................12
3.2 Rear Panel ...........................................................................................................................................13
3.2.1 Rear Panel Part .........................................................................................................................13
3.2.2 Rear Accessory Connector ........................................................................................................14
Chapter 4 Electrical Connections .....................................................................................................................15
4.1 Power Supply Connections ..................................................................................................................15
4.1.1 AC Input Power Connection.......................................................................................................15
4.1.2 Ground Connection....................................................................................................................16
4.1.3 Battery Backup Connection .......................................................................................................16
4.2 RF Antenna Connections .....................................................................................................................17
4.2.1 Duplexer Selection.....................................................................................................................17
4.2.2 Antenna Selection......................................................................................................................17
Chapter 5 Post-Installation Checklist................................................................................................................18
5.1 Applying Power ....................................................................................................................................18
5.2 Verifying Proper Operation...................................................................................................................18
5.2.1 Front Panel LEDs14
5.3 Archiving ..............................................................................................................................................18
5.3.1 Copying the Repeater Codeplug Data to a Computer ...............................................................18

Page 1
Foreword
This manual is intended for use by experienced technicians familiar with similar types of equipment. Speci-
cally, it contains installation information required for the Vertex Standard (9X-R70 Repeater.
Product Safety and RF Exposure Compliance
See Installation Requirements for Compliance with Radio Frequency (RF) Energy Exposure Safety Stan-
dards on next page.
Computer Software Copyrights
The Vertex Standard products described in this manual may include copyrighted Vertex Standard computer
programs stored in semiconductor memories or other media. Laws in the United States and other countries
preserve for Vertex Standard certain exclusive rights for copyrighted computer programs, including, but not
limited to, the exclusive right to copy or reproduce in any form the copyrighted computer program. According-
ly, any copyrighted Vertex Standard computer programs contained in the Vertex Standard products described
in this manual may not be copied, reproduced, modied, reverse-engineered, or distributed in any manner
without the express written permission of Vertex Standard. Furthermore, the purchase of Vertex Standard
products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license
under the copyrights, patents or patent applications of Vertex Standard, except for the normal non-exclusive
license to use that arises by operation of law in the sale of a product.
Document Copyrights
No duplication or distribution of this document or any portion thereof shall take place without the express
written permission of Vertex Standard. No part of this manual may be reproduced, distributed, or transmitted
in any form or by any means, electronic or mechanical, for any purpose without the express written permis-
sion of Vertex Standard.
Disclaimer
The information in this document is carefully examined, and is believed to be entirely reliable. However, no
responsibility is assumed for inaccuracies. Furthermore, Vertex Standard reserves the right to make changes
to any products herein to improve readability, function, or design. Vertex Standard does not assume any li-
ability arising out of the applications or use of any product or circuit described herein; nor does it cover any
license under its patent rights nor the rights of others.
Trademarks
Vertex Standard, the Stylized VS logo are registered in the US Patent & Trademark Ofce. All other product
or service names are the property of their respective owners.
© 2011 by Vertex Standard Co., Ltd.
Foreword

Page 2
Installation Requirements for Compliance with
Radio Frequency (RF) Energy Exposure
Safety Standards
ATTENTION!
This radio is intended for use in occupational/controlled conditions, where users have full knowl-
edge of their exposure and can exercise control over their exposure to meet FCC limits. This radio
device is NOT authorized for general population, consumer, or any other use.
To ensure compliance to RF Energy Safety Standards:
• Install only Vertex Standard approved antennas and accessories
• Be sure that Product Safety and RF Safety Booklet enclosed with this radio is available to the end user
upon completion of the installation of this radio
Before using this product, the operator must be familiar with the RF energy awareness information and oper-
ating instructions on the “Product Safety and RF Exposure” chapter beginning with page 4 to ensure compli-
ance with Radio Frequency (RF) energy exposure limits.
For a list of Vertex Standard-approved antennas and other accessories, visit the following web site which lists
approved accessories for your radio model:
http://www.vertexstandard.com/lmr
Installation Requirements for Compliance with Radio Frequency (RF) Energy Exposure Safety Standards

Page 3
Declaration of Conformity
This declaration is applicable to your radio only if your radio is labeled with the FCC logo shown below.
DECLARATION OF CONFORMITY
Per FCC CFR 47 Part 2 Section 2.1077(a)
Responsible Party
Name: Vertex Standard USA, Inc.
Address: 8000 West Sunrise Blvd, Ft. Lauderdale, FL 33322
Hereby declares that the product:
Model Name: (9X-R70
conforms to the following regulations:
FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section 15.109(a)
Class B Digital Device
As a personal computer peripheral, this device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause
undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digi-
tal device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not in-
stalled and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not oc-
cur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the re-
ceiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Declaration of Conformity

Page 4
ATTENTION!
BEFORE USING THIS RADIO, READ THIS CHAPTER WHICH CONTAINS IMPORTANT OPER-
ATING INSTRUCTIONS FOR SAFE USAGE AND RF ENERGY AWARENESS AND CONTROL
INFORMATION FOR COMPLIANCE WITH RF ENERGY EXPOSURE LIMITS IN APPLICABLE
NATIONAL AND INTERNATIONAL STANDARDS.
The information provided in this document supersedes the general safety information contained in user
guides published prior to February 2002.
RF Energy Exposure Awareness and Control Information, and Operational Instructions for FCC Occu-
pational Use Requirements
NOTICE: This radio is intended for use in occupational/controlled conditions, where users have full
knowledge of their exposure and can exercise control over their exposure to meet FCC lim-
its. This radio device is NOT authorized for general population, consumer, or any other use.
This 2-way radio uses electromagnetic energy in the radio frequency (RF) spectrum to provide communica-
tions between two or more users over a distance. It uses radio frequency (RF) energy or radio waves to send
and receive calls. RF energy is one form of electromagnetic energy. Other forms include, but are not limited
to, sunlight and x-rays. RF energy, however, should not be confused with these other forms of electromagnet-
ic energy, which when used improperly, can cause biological damage. Very high levels of x-rays, for example,
can damage tissues and genetic material.
Experts in science, engineering, medicine, health, and industry work with organizations to develop standards
for safe exposure to RF energy. These standards provide recommended levels of RF exposure for both workers
and the general public. These recommended RF exposure levels include substantial margins of protection.
All Vertex Standard 2-way radios are designed, manufactured, and tested to ensure they meet government-
established RF exposure levels. In addition, manufacturers also recommend specic operating instructions to
users of 2-way radios. These instructions are important because they inform users about RF energy exposure
and provide simple procedures on how to control it.
Please refer to the following Web sites for more information on what RF energy exposure is and how to con-
trol your exposure to assure compliance with established RF exposure limits.
http://www.fcc.gov/oet/rfsafety/rf-faqs.html
http://www.osha.gov/SLTC/radiofrequencyradiation/index.html
Federal Communication Commission Regulations
The FCC rules require manufacturers to comply with the FCC RF energy exposure limits for mobile 2-way ra-
dios before they can be marketed in the U.S. When 2-way radios are used as a consequence of employment,
the FCC requires users to be fully aware of and able to control their exposure to meet occupational require-
ments. Exposure awareness can be facilitated by the use of a label directing users to specic user awareness
information. Your Vertex Standard 2-way radio has a RF exposure product label. Also, your Vertex Standard
user manual, or separate safety booklet, includes information and operating instructions required to control
your RF exposure and to satisfy compliance requirements.
Compliance with RF Exposure Standard
Your Vertex Standard two-way radio is designed and tested to comply with a number of national and interna-
tional standards and guidelines (listed below) regarding human exposure to radio frequency electromagnetic
energy. This radio complies with the IEEE and ICNIRP exposure limits for occupational/controlled RF expo-
sure environment at duty factors of up to 50% talk-50% listen and is authorized by the FCC for occupational
use. In terms of measuring RF energy for compliance with the FCC exposure guidelines, your radio antenna
radiates measurable RF energy only while it is transmitting (during talking), not when it is receiving (listening)
or in standby mode.
Product Safety and RF Exposure

Page 5
Your Vertex Standard two-way radio complies with the following RF energy exposure standards and
guidelines:
United States Federal Communications Commission, Code of Federal Regulations; 47CFR part 2 sub-
part J
American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers (IEEE) C95.
1-1992
Institute of Electrical and Electronic Engineers (IEEE) C95.1-1999 Edition
International Commission on Non-Ionizing Radiation Protection (ICNIRP) 1998
Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure to Radiofrequency Electromagnetic
Fields in the Frequency Range from 3 kHz to 300 GHz, 1999
Australian Communications Authority Radiocommunications (Electromagnetic Radiation - Human Expo-
sure) Standard, 2003
 ANATEL, Brasil Regulatory Authority, Resolution 256 (April 11, 2001) “additional requirements for SMR,
cellular, and PCS product certication.”
RF Exposure Compliance and Control Guidelines and Operating Instructions
To control exposure to yourself and others and to ensure compliance with the RF exposure limits, always ad-
here to the following procedures.
Guidelines:
User awareness instructions should accompany device when transferred to other users.
Do not use this device if the operational requirements described herein are not met.
Instructions:
Transmit no more than the rated duty factor of 50% of the time. To transmit (talk), push the Push-To-Talk
(PTT) button or, for radios equipped with VOX, speak into the microphone. The red LED will illuminate
when the radio is transmitting. To receive calls, release the PTT button, or, for radios equipped with VOX,
stop talking. The red LED will extinguish when the radio stops transmitting. Transmitting 50% of the time,
or less, is important because this radio generates measurable RF energy exposure only when transmit-
ting (in terms of measuring for standards compliance).
Transmit only when people outside the vehicle are at least the recommended minimum lateral
distance away, as shown in Table 1, from the body of a vehicle with a properly installed antenna.
This separation distance will ensure that there is sufcient distance from a properly installed (according to
installation instructions) externally-mounted antenna to satisfy the RF exposure requirements in the stan-
dards listed above.
NOTE: Table 1 below lists the recommended lateral distance for people in an uncontrolled environment
from the body of a vehicle with an approved, properly installed transmitting antenna (i.e., mono-
poles over a ground plane, or dipoles) at several different ranges of rated radio power for mobile
radios installed in a vehicle.
Table 1. Rated Power of Vehicle-Installed Mobile Two-Way Radio and
Recommended Minimum Lateral Distance from Vehicle Body
Mobile Radio Rated Power (see Note) Minimum Lateral Distance from Vehicle Body
Less than 7 watts 8 inches (20 centimeters)
7 to 15 watts 1 foot (30 centimeters)
16 to 39 watts 2 feet (60 centimeters)
40 to 110 watts 3 feet (90 centimeters)
When a mobile radio is used in conjunction with another co-located transmitter such as a Vehicular Re-
peater, it is the vehicle operator’s responsibility to take appropriate steps to keep bystanders at the re-
quired separation distance from the vehicle to ensure compliance with the FCC’s RF energy exposure
limits for the general population. See the co-located transmitter’s user manual for more details.
Product Safety and RF Exposure

Page 6
NOTE:If you are not sure of the rated power of your radio, contact your Vertex Standard representative or
dealer and supply the radio model number found on the radio model label. If you can not determine
the rated power out, then assure 3-feet separation from the body of the vehicle. The maximum power
shown on the FCC Grant may be higher than the rated power allowing for production variation.
Mobile Antenna Installation Guidelines
These mobile antenna installation guidelines are limited to metal body motor vehicles or vehicles with ap-
propriate ground planes.
Antennas should be installed in the center area of the roof or the trunk lid taking into account exposure
conditions of backseat passengers and according to the specic instructions and restrictions in the Radio
Installation Manual along with the requirements of the antenna supplier.
 Trunk lid installations are limited to vehicles with clearly dened at trunk lids, and in some cases, to spe-
cic radio models and antennas. See the Radio Installation Manual for specic information on how and
where to install specic types of approved antennas to facilitate recommended operating distances to all
potentially exposed persons.
Use only the Vertex Standard -approved, supplied antenna or a Vertex Standard-approved re-
placement antenna. Unauthorized antennas, modications, or attachments could damage the radio and
may result in non-compliance with RF Safety Standards.
Approved Accessories
This radio has been tested and meets RF Safety Standards when used with the Vertex Standard acces-
sories supplied or designated for this product. Use of other accessories may result in non-compliance
with RF Safety Standards.
For a list of Vertex Standard -approved antennas, visit the following Web site, which lists approved acces-
sories for your radio model:
http://www.vertexstandard.com/lmr.
Compliance and Control Guidelines and Operating Instructions for Mobile Two-Way Radios Installed
as Fixed Site Control Stations
If mobile radio equipment is installed at a xed location and operated as a control station or as a xed unit,
the antenna installation must comply with the following requirements in order to ensure optimal performance
and compliance with the RF energy exposure limits in the standards and guidelines listed on page 4:
The antenna should be mounted outside the building on the roof or a tower if at all possible.
 As with all xed site antenna installations, it is the responsibility of the licensee to manage the site in ac-
cordance with applicable regulatory requirements and may require additional compliance actions such as
site survey measurements, signage, and site access restrictions in order to ensure that exposure limits
are not exceeded.
For additional installation information, see the guidelines for minimum separation distances provided
above in the RF Exposure Compliance and Control Guidelines and Operating Instructions section of this
document.
Electromagnetic Interference/Compatibility
NOTE: Nearly every electronic device is susceptible to electromagnetic interference (EMI) if inadequately
shielded, designed, or otherwise congured for electromagnetic compatibility. It may be necessary to
conduct compatibility testing to determine if any electronic equipment used in or around vehicles or near
xed site antenna is sensitive to external RF energy or if any procedures need to be followed to elimi-
nate or mitigate the potential for interaction between the radio transmitter and the equipment or device.
Product Safety and RF Exposure

Page 7
Facilities
To avoid electromagnetic interference and/or compatibility conicts, turn off your radio in any facility where
posted notices instruct you to do so. Hospitals or health care facilities may be using equipment that is sensi-
tive to external RF energy.
Vehicles
To avoid possible interaction between the radio transmitter and any vehicle electronic control modules, such
as ABS, engine, or transmission controls, the radio should be installed only by an experienced installer and
the following precautions should be used when installing the radio:
1. Refer to the manufacturer’s instructions or other technical bulletins for recommendations on radio installation.
2. Before installing the radio, determine the location of the electronic control modules and their harnesses in
the vehicle.
3. Route all radio wiring, including the antenna transmission line, as far away as possible from the electronic
control units and associated wiring.
Driver Safety
Check the laws and regulations on the use of radios in the area where you drive. Always obey them.
When using your radio while driving, please:
Give full attention to driving and to the road.
Pull off the road and park before making or answering a call if driving conditions so require.
Operational Warnings
For Vehicles with an Air Bag
Do not mount or place a mobile radio in the area over an air bag or in the air bag deployment
area. Air bags inate with great force.
If a radio is placed in the air bag deployment area and the air bag inates, the radio may be
propelled with great force and cause serious injury to occupants of the vehicle.
Potentially Explosive Atmospheres
Turn off your radio prior to entering any area with a potentially explosive atmosphere. Sparks
in a potentially explosive atmosphere can cause an explosion or re resulting in bodily injury
or even death.
The areas with potentially explosive atmospheres include fueling areas such as below decks
on boats, fuel or chemical transfer or storage facilities, and areas where the air contains
chemicals or particles such as grain, dust or metal powders. Areas with potentially explosive
atmospheres are often, but not always, posted.
Blasting Caps and Blasting Areas
To avoid possible interference with blasting operations, turn off your radio when you are near
electrical blasting caps, in a blasting area, or in areas posted: “Turn off two-way radio.” Obey
all signs and instructions.
For radios installed in vehicles fueled by liqueed petroleum gas, refer to the (U.S.) National
Fire Protection Association standard, NFPA 58, for storage, handling, and/or container infor-
mation. For a copy of the LP-gas standard, NFPA 58, contact the National Fire Protection As-
sociation, One Battery Park, Quincy, MA.
Product Safety and RF Exposure

Page 8
Chapter 1 Pre-Installation Considerations
Proper installation ensures the best possible performance and reliability of the (9X-R70 Repeater.
Pre-installation planning is required. This includes considering the mounting location of the repeater
in relation to input power and antennas. Also consider the site environmental conditions, the par-
ticular mounting method (several available), and required tools and equipment.
If this is the rst time this type of equipment is being installed, it is highly recommended that the
user read this entire installation section before beginning the actual installation.
1.1 Installation Overview
The following information is an overview for installing the (9X-R70 Repeater and ancillary equipment.
• Plan the installation, paying particular attention to environmental conditions at the site, ventila-
tion requirements, and grounding and lightning protection.
• Unpack and inspect the equipment.
• Mechanical install the equipment at the site.
• Make necessary electrical and cabling connections, including the following:
- AC input cabling
- Coaxial cables to transmit and receive antennas
• Perform a post-installation function checkout test of the equipment to verify proper installation.
• Proceed to customize the repeater parameters per customer specications (e.g. operating fre-
quency, PL, codes, color code, etc.).
1.2 Environmental Conditions at Intended Installation Site
The repeater may be installed in any location suitable for electronic communications equipment,
provided that the environmental conditions do not exceed the equipment specications for tempera-
ture, humidity, and air quality.
NOTE: The (9X-R70 Repeater has been manufactured with a power-saving main fan. The fan
powers ON temporarily as a self-check after user initially turns the repeater power ON. If
the repeater’s internal ambient temperature remains below 30°C (86°F), the fan does not
operate. It powers ON and remains operational only after the repeater’s internal ambient
temperature rises above 30°C (86°F), and its speed increases as the temperatures rises.
At 50°C (122°F), the fan runs at full speed.
1.2.1 Operating Temperature Range
-30°C (-22°F) to +60°C (+140°F)
This is the temperature measured in close proximity to the repeater. For example, if the repeater is
mounted in a cabinet, the temperature within the cabinet is measured.
1.2.2 Humidity
Humidity conditions should not exceed 95% relative humidity @ 50°C (122°F).
1.2.3 Air Quality
For equipment operating in an area which is environmentally controlled and with the repeater(s)
rack mounted, the airborne particle level must not exceed 25 μg/m³.
For equipment operating in an area which is not environmentally controlled and with the repeater(s)
cabinet mounted, airborne particle level must not exceed 90 μg/m³.
If the repeater is to be installed in an environment which is usually dusty,
dirty, or does not meet the air quality requirements, then the air used to cool
the repeater modules must be treated using appropriate filtering devices.
Dust or dirt accumulating on the internal circuit boards and modules is not
easily removed, and can cause such malfunctions as overheating and inter-
mittent electrical connections.
Chapter 1 Pre-Installation Considerations

Page 9
1.3 Equipment Ventilation
The repeater is equipped with a cooling fan that is used to provide forced convection cooling. When
planning the installation, observe the following ventilation guidelines:
• Customer-supplied cabinets must be equipped with ventilation slots or openings in the front (for
air entry) and back or side panels (for air to exit). If several repeaters are installed in a single
cabinet, ensure ventilation openings surrounding each repeater allow for adequate cooling.
• All cabinets must have a least 15 cm (6 inches) of open space between the air vents and any
wall or other objects.
• When multiple cabinets (each equipped with several repeaters) are installed in an enclosed
area, ensure appropriate ventilation and consider air conditioning or other climate control equip-
ment to satisfy the temperature requirements stated under Section 1.2.1 Operating Temperature
Range on page 8.
1.4 AC Input Power Requirements
The repeater is equipped with a switching power supply, and this assembly operates from 100 –
240 VAC at 47 – 63 Hz AC input power. A standard 3-prong line cord is supplied to connect the
power supply to the AC source.
It is recommended that a standard 3-wire grounded electrical outlet be used
as the AC source.
The outlet must be connected to an AC source capable of supplying a maximum of 280 W. For
a nominal 110/120 VAC input, the AC source must supply 5 A and should be protected by circuit
breaker rated at 15 A. For a nominal 220/240 VAC input, the AC source must supply 3 A and should
be protected by a circuit breaker rated at 10 A.
1.4.1 Circuit Overloading
Consideration should be given to the effects of overloading on overcurrent protection devices and
supply wiring. Appropriate consideration of equipment ratings should be used when addressing
this concern.
1.5 Equipment Mounting Methods
The (9X-R70 Repeater may be mounted in a rack, bracket or cabinet (available as accessories).
1.6 Site Grounding and Lightning Protection
Proper site grounding and lightning protection are vitally important consider-
ations. Failure to provide proper lightning protection may result in permanent
damage to the radio equipment.
One of the most important considerations when designing a communications site is the ground and
lightning protection system. While proper grounding techniques and lightning protection are closely
related, the general category of site grounding may be divided into the following section.
1.6.1 Electrical Ground
Ground wires carrying electrical current from circuitry or equipment at the site is included in the cat-
egory of electrical ground. Examples include the AC or DC electrical power used to source equip-
ment located at the site, and wires or cables connected to alarms or sensors located at the site.
1.6.2 RF Ground
This type of ground is related to the bypassing of unwanted radio frequency energy to earth ground.
An example of RF grounding is the use of shielding to prevent or at least minimize the leakage of
unwanted RF energy from communications equipment and cables.
Chapter 1 Pre-Installation Considerations

Page 10
1.6.3 Lightning Ground
Providing adequate lightning protection is critical to a safe reliable communications site. RF trans-
mission cables, and AC and DC power lines must all be protected to prevent lightning energy from
entering the site.
Comprehensive coverage of site grounding techniques and lightning protection is not within the
scope of this instruction manual, but there are several excellent industry sources for rules and
guidelines on grounding and lightning protection at communications sites.
1.6.4 Equipment Grounding
The repeater is equipped with a ground screw located on the rear of the repeater power supply
module. This screw is used to connect the repeater to the site grounding. All antenna cables, and
AC and DC power cabling, should be properly grounded and lightning protected by following the
rules and guidelines provided in the above reference. Failure to provide proper lightning protection
may result in permanent damage to the radio equipment.
Chapter 1 Pre-Installation Considerations

Page 11
Chapter 2 Mechanical Installation
Chapter 2 Mechanical Installation
This section describes the procedures to unpack and mechanically install the (9X-R70 Repeater. A variety
of mounting methods are possible depending on which type of cabinet or rack (if any) has been selected to
house the repeater(s).
Be sure to observe proper electrostatic discharge precautions if modules
must be removed from the repeater.
2.1 Unpacking Equipment
The following items are packed together in the box:
• (9X-R70 Repeater
• AC Line Cord
• (9X-R70 Repeater Installation Guide (This Booklet)
Inspect the equipment for damage immediately after unpacking, and
make a report of the extent of any damage to the transportation com-
pany and to Vertex Standard.
2.2 Transferring Equipment from Shipping Container to Rack or Cabinet
The repeater is shipped in a box. Upon delivery, the equipment must be removed from the container
and transferred to a rack or cabinet.
NOTE: Customer-supplied cabinets and racks must have mounting rail and hole spacing compat-
ible with EIA Universal 48.3 cm (19 inches) specications. Cabinets must provide adequate
ventilation (see “Environmental Conditions at Intended Installation Site” on page 4) and
must meet the following minimum criteria:
- 41.3 cm (16.25 inches) deep
- 48.3 cm (19 inches) wide
- 13.4 cm (5.25 inches) high
- Two mounting rails 5 cm (2 inches) from the front of the cabinet with front mounting
holes 5.7 cm (2.25 inches) apart (center to center).
Contact Vertex Standard Technical Support for specic question(s) regarding mounting equipment
in customer-supplied cabinets.

Page 12
Chapter 3 Indicators and Connectors
3.1 Front Panel
Chapter 3 Indicators and Connectors
3.1.1 LED Indicator Descriptions
LED Status Description
POWER
Solid GREEN Repeater powered by AC.
Solid RED Repeater powered by backup battery.
Off Repeater powered off.
DISABLED
Solid RED Repeater function disabled.
Blinking RED Repeater in self-test mode.
Off Repeater in normal operation mode.
DIGITAL Solid BLUE Repeater in Digital Mode.
ANALOG Solid YELLOW Repeater in Analog Mode.
TX A Solid GREEN Repeater transmitting (Analog).
Solid GREEN Repeater transmitting on Slot A (Digital).
RX A Solid YELLOW Repeater receiving (Analog).
Solid YELLOW Repeater receiving on Slot A (Digital).
TX B Solid GREEN Repeater transmitting on Slot B (Digital).
RX B Solid YELLOW Repeater receiving on Slot B (Digital).

Page 13
Chapter 3 Indicators and Connectors
3.2.1 Rear Panel Part
3.2 Rear Panel
No Item Description
Rx Connector BNC (Female).
Power Supply On/Off Switch Turns on or off the power to the repeater from AC input.
Battery Backup Connector
(DC Input)
Backup battery supplies backup power to the repeater.
The battery is an optional accessory. The repeater will
trickle charge battery, but an external charger is recom-
mended to equalize battery after a prolonged use. Auto
switching from AC to battery with loss of AC power is a
function of the standard repeater power supply. Supply
will automatically switch back to AC operation upon the
return of AC power.
The front panel power LED switches from green to red
when on battery power.
Power Supply Fan Runs continuously to cool the repeater.
Main Power Supply Connector
(AC Input)
100 - 240 Volts.
Rear Accessory Connector Programming cable plugs in here.
Ethernet Connector 100Base-TX (RJ45).
Main Fan Variable speed. Idles at room temperature. Speeds up
with extended use of the repeater.
Tx Connector Type-N (Female).
Ground Screw Must be connected to System Ground.

Page 14
Chapter 3 Indicators and Connectors
3.2.2 Rear Accessory Connector
The rear accessory connector is located above the ethernet connector. Most of the Vertex Stan-
dard-approved accessories are supplied with female terminals crimped to a 20-gauge wire speci-
cally designed to t the housing of the rear accessory connector.
Insert the female terminal into the accessory connector housing in the appropriate locations. The
accessory connector housing is provided together with the accessory. Connect the accessory
connector housing to the rear accessory connector on the back of the repeater. Do not use other
generic terminals in the housing. Generic terminals can cause electrical intermittences and may
cause damage to the housing.
Pin No. Pin Name Pin Function Pin No. Pin Name Pin Function
1 D+ USB + (Data) 14 Rx Audio Receive Live Audio2
2 D- USB - (Data) 15 AUX Audio 2 Public Address 2
3VBUS USB Power
(5V from USB accessory/cable) 16 GND Ground
4USB/MAP_ID GND USB/MAP_ID Ground 17 GP5-1 (PTT) 5V Level GPIO, PTT Input1
5MAP_ID_2 Accessory Identier 18 GND Ground
6MAP_ID_1 Accessory Identier 19 GP5-2 (Monitor) 5V Level GPIO, Monitor Input3
7SW B+ Switched Battery Voltage 20 GP5-6 5V Level GPIO
8 PWRGND Ground 21 GP5-3 5V Level GPIO,
Channel Activity Function
9 SPKR- Speaker -
(3.2 ohm minimum impedance) 22 GP5-7 5V Level GPIO
10 SPKR+ Speaker +
(3.2 ohm minimum impedance) 23 EMERGENCY Emergency Switch Input
11 Tx Audio Rear External Microphone Input424 GP5-8 No connection
12 Audio GND Audio Ground 25 IGN SENSE No connection
13 AUX Audio 1 Public Address 1 26 VIP-1 12V Tolerant, 5V GPIO,
External alarm
1 Pulling this line to ground activates the PTT function, thus activating the AUX_MIC input.
2 Fixed level (independent of volume level) received audio signal, including alert tones. Flat or de-emphasis are programmed by the
Programming Software. Output voltage is approximately 330 mVrms for 1kHz of deviation.
3 This input is used to detect when a rear microphone accessory is taken off-hook.
4 This microphone signal is independent of the microphone signal on the front microphone connector. The nominal input level is
80mVrms for 60% deviation. The DC impedance is 660 ohms and the AC impedance is 560 ohms.
Table: Rear Accessory Connector Pin Functions

Page 15
Chapter 4 Electrical Connections
After the (9X-R70 Repeater has been mechanically installed, electrical connections must be
made. This involves making the following connections:
• AC power cord, and
• antenna coaxial cables
Figure 4-1 shows the position of the various connectors and connections on the rear panel of
the repeater.
Figure 4-1: Locations of Connectors on the Rear Panel of the Repeater
4.1 Power Supply Connections
4.1.1 AC Input Power Connection
Do NOT apply AC power to the repeater at this time. Make sure that the cir-
cuit breaker associated with the AC outlet is turned to OFF.
NOTE: The AC source must be installed near the equipment and must be easily accessible.
Each repeater ships with a 2.438 m (8 feet) 3-conductor line cord that connects the repeater to a
110/120/220/240 VAC source. Figure 4-1 shows the location where the AC line cord connects to the
repeater. Insert the 3-prong plug into a 110/120/220/240 VAC grounded outlet.
If an alternate line cord is required, obtain a suitable line cord, with ttings approved by the safety
testing agency in the end-use country, from a certied electrical parts supplier.
Chapter 4 Electrical Connections

Page 16
4.1.2 Ground Connection
The repeater is equipped with a ground screw located on the rear of the repeater. Connect the site
ground cable to the ground screw.
The repeater should only be connected to a battery supply that is in accor-
dance with the applicable electrical codes for the end use country; for ex-
ample, the National Electrical Code ANSI/NFPA No. 70 in the U.S.
4.1.3 Battery Backup Connection
The (9X-R70 Repeater offers the capability of connecting to battery backup power in the event of
an AC power failure.
The battery backup system is connected to the repeater through the DC connector mounted at the
rear of the repeater (see Figure 4-2).
The repeater power supply will trickle charge the backup battery. If the battery is significantly
discharged, it is recommended that an external charger be used to charge the battery.
The repeater is to be connected to a battery charger that is in accordance
with the applicable electrical codes for the end use country; for example, the
National Electrical Code ANSI/NFPA No.70 in the U.S.
Unplug the battery from the repeater when charging the battery with an
external charger.
Chapter 4 Electrical Connections
Figure 4-2: Making Connections to a Backup Battery

Page 17
Chapter 4 Electrical Connections
4.2 RF Antenna Connections
The transmit and receive antenna RF connection are made using two separate connectors. Coaxial
cables from the receive and transmit antenna must be connected to the Type-N (Tx) and BNC (Rx)
connectors. The position of these connectors is shown in Figure 4-1. For repeater use, the anten-
nas need adequate isolation between them, or if one antenna is used, the duplexer needs to have
adequate isolation between the Tx and Rx ports. The isolation requirements are unique to each
band and are shown in the table below:
If the duplexer isolation is not adequate, a preselector may also be used.
The repeater can key up at any time due to input from a subscriber unit or a
CW ID. Please ensure that all power is switched off before disconnecting the
transmit antenna.
4.2.1 Duplexer Selection
The selection of a duplexer is critical to system performance. The use of a notch (band reject) du-
plexer is possible in some systems that are not located at high RF density sites.
The duplexer must be able to handle at least 50 W continuously. For the best system performance,
the insertion loss should be less than 2 dB. If the repeater is used in higher RF density sites, the
use of a pass-notch duplexer is recommended.
4.2.2 Antenna Selection
The selection of the antenna is critical to system performance. The selected antenna must be 50
Ohm impedance and capable of at least 50 Watts. Gain antennas may be used to increase system
coverage. Please take note of licensing restrictions when selecting gain antennas. Some services
or regions may have antenna gain or system ERP limitations.
The antenna must be connected to the duplexer with a high grade 50 Ohm transmission line (hard-
line). The line must have connectors to match the connectors on the duplexer and antenna.
It is important that all antenna cables are grounded at the point they enter
the building.
The antenna design is the customer’s responsibility. All aspects of the
antenna design must comply with the relevant local regulations.
Frequency Band Bandwidth Isolation
VHF 136-174 MHz 85 dB
UHF 1 403-470 MHz 75 dB
UHF 2 450-512 MHz 85 dB

Page 18
Chapter 5 Post-Installation Checklist
After the (9X-R70 Repeater has been mechanically installed and all electrical connections have
been made, power may now be applied and the repeater checked for proper operation.
5.1 Applying Power
Before applying power to the repeater, make sure all boards are securely seated in the appropriate
connectors on the backplane and that all RF cables are securely connected.
Turn ON the circuit breaker controlling the AC outlet that is supplying power to the repeater Power
Supply Module.
5.2 Verifying Proper Operation
Operation of the repeater can be veried by:
• observing the state of the 8 LEDs located on the front panel, and
• exercising radio operation.
Some repeater components can become extremely hot during operation.
Turn off all power to the repeater and wait until sufciently cool before touch-
ing the repeater.
5.2.1 Front Panel LEDs
After turning ON the repeater power (or after a repeater reset), the 8 LEDs on the repeater
front panel:
• Light for about one second to indicate that they are functional, then
• Go off for one second, then
• Indicate the operational status of the repeater.
5.3 Archiving
5.3.1 Copying the Repeater Codeplug Data to a Computer
Backup the repeater’s codeplug data by using the Programming Software on a computer.
Chapter 5 Post-Installation Checklist