Vertiv Tech SmartCabinet2-E Series User manual

SmartCabinet2-E Series Computer Room Solution Product
User Manual
Version V1.30
Revision Date 2020-06-18
BOM
Vertiv Tech Co., Ltd. provides customers with technical support. Users may contact the nearest
Vertiv local sales office or service center.
Copyright by Vertiv Tech Co., Ltd.
All rights reserved. The contents in this document are subject to change without notice.
Vertiv Tech Co., Ltd.
Address: XUEYUAN ROAD, NANSHAN I PARK, BLOCK B2, NANSHAN DISTRICT, SHENZHEN
China
Post Code: 518055
Homepage: www.Vertiv.com
Customer service hotline: [phone]（GC only）
E-mail: [e-mail]

Safety precautions
1. Keep this manual throughout the life of the product.
2. Users should read this manual carefully before performing any operation on the product.
3. “Notices” and “Warnings” in this manual do not represent all safety precautions to be observed, but they are
only supplements to various operational safety precautions.
4. This product is professional equipment, used in industrial, commercial or other professional occasions, not to
the general public.
5. This product is only used for the purpose of its design. The manufacturer will not bear any responsibility for
incorrect use.
6. The key provided by the product must be kept by the person responsible for maintenance.
Electrical safety
Dangerous voltage
Danger
Some components of the system carry dangerous voltage in operation. Direct contact or indirect contact
through moist objects with these components will result in fatal injury.
Safety rules in the industry must be observed for installation of the AC power supply. The installation personnel
must be licensed to operate high voltage and AC power.
Never wear a watch, bracelet, bangle, ring, or other conductive objects during operation.
When water or moisture is found on the cabinet, turn off the power immediately. In a moist environment,
precautions must be taken to keep moisture out of the power supply.
In the installation process, a prohibition signboard must be put on the operating switch and button.
Danger
High voltage construction operation may cause fire or electric shock. Areas for connection and wiring of
AC cables must be in compliance with the local rules and regulations.Only those who are licensed to
operate high voltage and AC power can perform high voltage operations.
High leakage current
Warning
High contact current must be grounded before power connection.
Tools
Warning
In high voltage and AC operation, special tools must be used. No common or self-carried tools should be
used.
危险
危险
危险
危险

In thunderstorms, a strong electromagnetic field will be generated in the air. Therefore, equipment should be well
earthed in time to avoid damage by lightning strikes.
ESD
Notices
Static electricity generated by the human body will damage the static sensitive elements, such as large-
scale integrated circuits (ICs), on the circuit board. Before touching the equipment or holding a plugboard,
the circuit board, or an IC chip, an ESD wrist strap must be worn to prevent body static electricity from
damaging the static sensitive elements. The other end of the ESD wrist strap must be well earthed.
Reversed connection
Warning
It is forbidden to connect the live wire (L) and neutral wire (N) of AC input in reverse. Otherwise, the
system equipment will be damaged.
Never wear a watch, bracelet, bangle, ring, or other conductive objects during operation.
Insulated tools must be used during operation.
During live operation, the hand, wrist, arm must be kept in the tense state, to prevent such an accident that the
tool or the human body moves with a large amplitude in the case of tool slipping.
Others
Sharp object
Warning
When moving the equipment by hand, wear protective gloves to avoid injury by sharp objects.
Power cable
Notices
Prior to cable connection, verify the compliance of the cable and cable label with the actual installation.
Binding of signal cables
Notices
The signal cables should be bound separately from heavy current or high voltage wires, with a binding
interval of at least 150 mm.
危险
危险
危险
危险
危险

Contents
Chapter 1 Product Overview...............................................................................................................................................1
1.1 Model Description.................................................................................................................................................1
1.2 Application Scenario.............................................................................................................................................1
1.3 Product Characteristics.........................................................................................................................................1
1.4 Product Specification and Appearance.................................................................................................................2
1.5 Using Environment................................................................................................................................................3
1.5.1 Operating Environment..............................................................................................................................3
1.5.2 Storage Environment.................................................................................................................................3
1.5.3 Space ........................................................................................................................................................3
1.5.4 Load Bearing Capacity ..............................................................................................................................4
1.6 System Architecture..............................................................................................................................................4
1.6.1 Cabinet Structural Components.................................................................................................................4
1.6.2 Power Supply and Distribution System......................................................................................................4
1.6.3 Cooling System .........................................................................................................................................6
1.6.4 Monitoring management system................................................................................................................6
1.6.5 Alarm system.............................................................................................................................................6
1.6.6 Lightning protection grounding system......................................................................................................6
1.7 Technical Specifications .......................................................................................................................................6
Chapter 2 Product Installation And Commissioning............................................................................................................8
2.1 Installation Preparation.........................................................................................................................................8
2.1.1 Materials....................................................................................................................................................8
2.1.2 Tools and Accessories...............................................................................................................................8
2.1.3 Installation Environment ..........................................................................................................................10
2.1.4 Personnel ................................................................................................................................................11
2.2 Equipment Installation.........................................................................................................................................11
2.2.1 Moving and Handling...............................................................................................................................11
2.2.2 Installing the Cabinet...............................................................................................................................12
2.2.3 ECO fan module......................................................................................................................................15
2.2.4 The wiring of water immersion sensor.....................................................................................................17
2.2.5 Battery module (optional).........................................................................................................................17
2.2.6 GSM MODEM installation (optional)........................................................................................................19
2.2.7 Install Airduct (optional)...........................................................................................................................20
2.2.8 User Cable Connection............................................................................................................................21
2.2.9 Installation Inspection..............................................................................................................................21
2.3 Software and Hardware Commissioning.............................................................................................................22
2.3.1 Commissioning process...........................................................................................................................22
2.3.2 Preparation..............................................................................................................................................22
2.3.3 Inspection................................................................................................................................................22
2.3.4 Startup commissioning ............................................................................................................................23
2.3.5 System commissioning............................................................................................................................24
2.3.6 Smart door lock commissioning...............................................................................................................25

2.3.7 Shutdown.................................................................................................................................................26
Chapter 3 Operation Settings............................................................................................................................................27
3.1 HMI Local Display Interface................................................................................................................................27
3.1.1 Introduction to Local Display....................................................................................................................27
3.1.2 Startup Screen.........................................................................................................................................27
3.1.3 Home.......................................................................................................................................................28
3.1.4 Thermal ...................................................................................................................................................28
3.1.5 Power ......................................................................................................................................................29
3.1.6 ENV.........................................................................................................................................................31
3.1.7 Alarm.......................................................................................................................................................31
3.1.8 Log ..........................................................................................................................................................32
3.1.9 Settings....................................................................................................................................................33
3.2 Remote WEB Intelligent Monitoring Access Interface.........................................................................................36
3.2.1 Login Preparation ....................................................................................................................................36
3.2.2 Logging in the remote monitoring platform ..............................................................................................40
3.2.3 Monitoring Homepage .............................................................................................................................41
3.2.4 Menu items..............................................................................................................................................44
3.3 ECO Settings and Operating Instructions...........................................................................................................70
3.3.1 Setting ECO Mode...................................................................................................................................70
3.3.2 Descriptions of Operating Conditions......................................................................................................70
Chapter 4 Maintenance.....................................................................................................................................................72
4.1 Precautions before Maintenance ........................................................................................................................72
4.2 Maintenance Preparation....................................................................................................................................72
4.2.1 Technical Materials..................................................................................................................................72
4.2.2 Tools........................................................................................................................................................72
4.2.3 Personnel ................................................................................................................................................73
4.3 Equipment Maintenance.....................................................................................................................................73
4.3.1 Maintenance of WEB Monitoring Unit......................................................................................................73
4.3.2 Air Conditioner System Maintenance ......................................................................................................74
4.3.3 UPS power distribution system maintenance ..........................................................................................76
4.4 Alarm reference ..................................................................................................................................................76
4.5 Troubleshooting..................................................................................................................................................77
4.6 Parts Replacement and Recycle.........................................................................................................................78
4.6.1 Replace equipment filter..........................................................................................................................78
4.6.2 Parts replacement and decomposition ....................................................................................................79
Appendix 1 System Wiring Diagram..................................................................................................................................80
Appendix 2 AC schematic diagram ...................................................................................................................................81

SmartCabinet2-E Series Computer Room Solution Product User Manual
Chapter 1 Product Overview 1
Chapter 1 Product Overview
The SmartCabinet 2-E series of computer room solution products (referred to as SmartCabinet 2-E products for
short) are the data cabinet solution products produced by Vertiv Tech Co., which are applied to micro data centers,
office areas and other indoor environments. The SmartCabinet 2-E products are used for installation and placement
of 19-inch cabinet-type hardware equipment in line with industry standards (EIA-310-E), including servers, voice,
data, Internet network equipment and including power supply and distribution system, air conditioning system, rack
support system, monitoring management system and fire subrack system (optional). It realizes the safe and efficient
operation of the miniature data center and maintains the normal and stable operation of the important equipment
such as the server inside the cabinet. It achieves standardized design and standardized on-site assembly without the
needs to elevate the floor and install outdoor unit, and the integrated delivery greatly shortens the delivery cycle.
The monitoring management system is based on the powerful data center monitoring and management platform of
Vertiv. It is compatible with the whole series of Vertiv products, and it is “Plug and Play”. It also provides additional
value which is difficult to achieve in separate purchasing such as energy consumption analysis. The new self-learning
ECO mode is adopted. Under the suitable equipment environment, the ECO fan is used to replace the air conditioner
to refrigerate the load. It has low noise and low power consumption, which greatly helps customers to quickly build a
green and healthy data center.
This chapter mainly introduces the model description, application scenario, product characteristics, appearance and
specifications, using environment, system architecture and performance indicators of SmartCabinet 2-E products.
1.1 Model Description
The model description of SmartCabinet 2-E is shown in Figure 1-1.
Figure 1-1 Model Description
1.2 Application Scenario
The SmartCabinet 2-E products mainly target small data center solutions in air-cooled scenarios. They are mainly
used in government, education, health care, transportation, energy, finance, small and medium-sized enterprises and
large company branches, and are mainly sold in China and Asia-Pacific region, and are usually applicable to
government agencies, bank outlets, offices, small data centers, etc.
1.3 Product Characteristics
Dust and noise control, high efficiency and energy saving: Fully closed operation and internal circulation system
to ensure the cleanliness of cabinets and temperature and humidity, prolong the life of IT equipment. The use of high
efficiency special UPS for computer room, combined with precision air conditioner, and sealed cold/hot aisle
technology, improves the efficiency of computer room refrigeration. The built-in fan and silent design make it suitable
for being used in the office area.

SmartCabinet2-E Series Computer Room Solution Product User Manual
2 Chapter 1 Product Overview
Intelligent monitoring: Integrating intelligent control functions such as environmental monitoring, equipment
monitoring, alarm linkage, etc., to provide a centralized monitoring platform for computer room management.
Highly integrated and space-saving: A standard cabinet provides constant operating conditions for all IT
equipment, and only power supply is needed at the user site. The system occupies no more than 1 m2 and is
compact and state-of-art.
Integrated air conditioner: The latest customized integrated TMM air conditioner equipment, which integrates
indoor and outdoor units, eliminates installation and maintenance troubles.
Friendly interface, unattended guarding: Ultra-large 9-inch HMI wide screen display integrates monitoring center
and display center in one, providing the equipment operation/alarm/security information at a glance, which is easy to
achieve all-weather remote monitoring of cabinet-level data center to meet different application scenarios.
Fast Delivery: Once in place, build in one hour, start in one day.
Access control management: Smart locks at cabinet level can be selected to ensure the safety of IT equipment in
cabinet.
Video management: Supporting IPC equipment, realizing video surveillance function of network camera.
ECO mode: The ECO mode can be activated intelligently according to the outside environment of the cabinet. The
whole load of fan equipment can be used for cooling, energy saving and noise reduction, environmental protection
and low carbon.
1.4 Product Specification and Appearance
Figure 1-2 SmartCabinet2-E product appearance （ Glass door on the left, sheet metal door on the right ）
Table 1-1 SmartCabinet2-E product specifications
Parameters
Specifications
Model
Local model
(mechanical lock)
Local model
(smart lock)
Asia Pacific model
(mechanical lock)
Asia Pacific model
(smart lock)
sheet metal door
(mechanical lock)
Dimensions (W×D×H)
600 mm×1200 mm×2150 mm (including ECO module) 770 mm×1330 mm×2500 mm (including Airduct)
Equipment installation
available height
24U(1U＝44.45mm)
IT equipment power
≤3kW
Voltage
L+N+PE, 220Vac/230Vac/240Vac

SmartCabinet2-E Series Computer Room Solution Product User Manual
Chapter 1 Product Overview 3
Parameters
Specifications
Sealed mode
Cold and hot aisles are fully sealed
Color
EG7021
Air conditioner cooling capacity
0.9~3.5W
Weight
<420kg
Noise
Overall<75dB, ECO mode only ≤50dB
1.5 Using Environment
1.5.1 Operating Environment
SmartCabinet 2-E products should be installed away from heat sources and sparks, avoid direct sunlight, and there
should be no corrosive gases and organic solvents in the room. The operating conditions are shown in Table 1-2.
Table 1-2 SmartCabinet2-E Operating Environment Requirements
Installation location
The installation site needs to be level;
The height of using space should not be less than 2400mm (If the Airduct is include , The height of using
space should not be less than 2700mm);
Using scenarios
In the computer room and office area, the front door is more than 1.2m away from the wall or obstacles
and the rear door is more than 1.0m away from the wall or obstacles.
Ambient
temperature
0˚C to 40˚C
Ambient humidity
≤80%RH (Notices *)
Altitude
< 2000m, air conditioners need to be derated for higher than 1000m
Rated operating
voltage
L+N+PE, 220Vac/230Vac/240Vac; 50/60Hz
Applicable form of
power grid
TN-S
Overvoltage level
II
Class of pollution
II
Notices *
When the whole unit runs in high temperature and humidity environment, condensation water may appear
outside the front glass door and the display panel, which is a normal phenomenon and does not affect the
use.
1.5.2 Storage Environment
The storage environment of SmartCabinet 2-E products is shown in Table 1-3.
Table 1-3 Storage Environment for SmartCabinet 2-E Products
Item
Requirement
Storage environment
Indoor, clean (no dust, etc.)
Ambient humidity
≤95%, (40˚C) RH
Ambient temperature
-25˚C to +55˚C
1.5.3 Space
When installing SmartCabinet 2-E, enough space should be reserved to facilitate the installation and maintenance of
cabinets. The required space for opening the front and rear doors of the cabinet is shown in Figure 1-3.

SmartCabinet2-E Series Computer Room Solution Product User Manual
4 Chapter 1 Product Overview
1. Front door of cabinet 2. Rear door of cabinet
Figure 1-3 SmartCabinet2-E Product Maintenance Space
The space using requirements of SmartCabinet 2-E model product are shown in Figure 1-4.
Figure 1-4 SmartCabinet2-E product using space
1.5.4 Load Bearing Capacity
The SmartCabinet 2-E product is heavier after the user equipment is installed in it, so the load-bearing capacity of the
computer room must be considered before installation. The SmartCabinet 2-E weighs about 350 kg. During
installation, it is necessary to evaluate the floor load-bearing according to the total weight of the equipment installed
by the users. If you can't determine, please consult the Vertiv office or the service center nearby.
1.6 System Architecture
1.6.1 Cabinet Structural Components
The cabinet adopts integrated sealed cold and hot aisle cabinet, which is used to install 19-inch hardware equipment
in line with industry standard (EIA-310-E), including server, voice, data, Internet network equipment and other
equipment. The whole rack system is fully sealed to keep the system clean, dust-free, energy-saving and noise
reduction (system noise ≤ 50dB with ECO mode).
1.6.2 Power Supply and Distribution System
The SmartCabinet 2-E product integrates ITA2 6kVA UPS, PMU and intelligent switch PDU components, provides
AC220V and DC12V/24V output, and provides a safe and reliable power supply system for the whole system and IT
load.
The SmartCabinet 2-E product integrates the latest ITA2 6kVA UPS, provides distribution support for IT load, air
conditioner equipment, ECO module, monitoring system and illumination system.