Vestil D-FORK User manual

1
Vestil Manufacturing Corporation
2999 North Wayne St., Angola, IN 46703
Ph: 260-665-7586 • Fax: [phone]
E-mail: [email protected]
www.vestil.com
SAFETY PRECAUTIONS
Readowner'smanualcompletelybeforeoperatingunit!
• Never exceed the maximum loading capacity of the
hoisting hook written on the warning label and capacity
label (p.2).
• Secure the hoisting hook using the screw clamp and
attach the safety chain to the mast of the fork truck
before use.
• Make sure the safety latch of the hook is secured
before lifting.
• Never load more than one load at a time.
• When elevation is not required, always transport the
load in the lower position.
• Consult factory if adding or performing any modifica-
tions to the original equipment.
• Use only replacement parts supplied or approved by
themanufacturer.
• Make sure all operator safety labels are in place (p.2).
Make sure the capacity label is clean and visible (p.2).
RECEIVING INSTRUCTIONS
Every unit is thoroughly tested and inspected prior
to shipment. However, it is possible that the unit may incur
damageduringtransit.Ifdamageis noticed when unloading,
make a note of it on the BILL OF LADING. Remove all
packing and strapping material, then inspect the unit again
fordamage.IF DAMAGE IS EVIDENT, FILEACLAIM WITH
THE CARRIER IMMEDIATELY!
HOISTING HOOKS
MODEL D-FORK
OWNER'S
MANUAL
Revised0107 08-126-101
A company dedicated to solving ergonomic and material
handling problems since 1955 .
HOISTING HOOKS
D-FORK SERIES
Fork Truck Attachments
Contents
Safety Precautions ....................................... 1
Receiving Instructions .................................. 1
Warranty....................................................... 1
Exploded Parts Drawing ............................... 2
Parts List....................................................... 2
Warning Label Identification ......................... 2
WARRANTY
This product is warranted for 90 DAYS from date of
purchaseto be free of manufacturingdefects in material and
workmanship. The manufacturer's obligation hereunder is
limitedtorepairingsuchproductsduringthewarrantyperiod,
provided the product is sent prepaid back to the factory.
This warranty does not cover normal wear of parts
or damage resulting from any of the following: negligent use
or misuse of the product, use or application contrary to
installation instructions, or disassembly, repair or alteration
by any person prior to authorization from a factory
representative.

2
HOISTING HOOKS • D-FORK SERIES
WARNING LABEL IDENTIFICATION
MAKE SURE ALL WARNING LABELS ARE IN PLACE!
* Product safety signs or labels should be
periodically inspected and cleaned by the
product users as necessary to maintain
good legibility for safe viewing distance.
ANSI 535.4 (10.21)
Contact manufacturer for replacement labels.
CAPACITY
LABEL
1
ITEM NO.
1
2
3
4
DESCRIPTION
X-Handle, Locking Screw
Strap and Hook
Shackle (4,000 lbs. cap.)
Shackle (10,000 lbs. cap.)
Clevis Hook (4,000 lbs. cap.)
Clevis Hook (10,000 lbs. cap.)
ENGINEERNO.
08-025-008
08-145-028
08-145-018
08-145-006
08-145-001
08-145-005
QTY.
2
1
1
1
1
1
PART NO.
DFK-THDL
DFK-STRAP
DFK-SHKL4
DFK-SHKL10
DFK-CLHOOK4
DFK-CLHOOK10
VESTIL MANUFACTURING COMPANY. ANGOLA, IN [phone]
MODEL, MODELO, MODÈLE
CAUTION PRECAUCION PRUDENCE
!!!
CONSULT FORKTRUCK OWNERS MANUAL FOR CAPACITY OFYOUR FORKTRUCK.
SAFETY CHAIN MUST BE FASTENED SECURELYTO FORKLIFT. TIP FORKS BACK
TO HELP KEEP ATTACHMENT FROM SLIDING OFF. FORK END MUST BE HIGHER
THANTHE BASE. DO NOT EXCEED RATED CAPACITY AS SHOWN BELOW.
CONSULTE EL MANUAL DEL PROPIETARIO DE LA TRANSPALETA PARA LA
CAPACIDAD DE SU TRANSPALETA. LA CADENA DE SEGURIDAD DEBE DE ESTAR
BIEN FIJADA A LA TRANSPALETA. INCLINE LAS HORQUILLAS HACIA ATRÁS
PARA EVITAR QUE EL FIJAMENTO SE DESLICE. EL EXTREMO DE LA HORQUILLA
DEBE DE ESTAR MÁS ELEVADO QUE LA BASE, NO EXCEDA LA CAPACIDAD QUE
SE MUESTRA ABAJO.
CONSULTER LE MANUEL DU PROPRIÉTAIRE POUR CHARIOT ÉLEVATEUR POUR
LA CAPACITÉ DEVOTRE CHARIOT ÉLEVATEUR. LA CHAÎNE DE
SÛRETÉ DOIT ÊTRE BIEN ATTACHÉE AU CHARIOT ÉLEVATEUR. RABATTRE LES
FOURCHES EN ARRIÈRE POUR ÉVITER UN GLISSEMENT DE LA
FIXATION. L’EXTRÉMITÉ DES FOURCHES DOIT ÊTRE PLUS ÉLEVÉE QUE
LA BASE. NE PAS EXCÉDER LA CAPACITÉ INDIQUÉE CI-DESSOUS.
CAPACITY OF THIS ATTACHMENT
CAPACIDAD DEL FIJAMENTO
CAPACITÉ DE CETTE FIXATION
lbs.
kgs.
1
237
1
2
3
4