Vetek EBW-2D User manual

USER MANUAL
Hantverksvägen 15
76493 Väddö, Sverige
Tel.[phone] www.vetek.se
[email protected]
1
WIRELESS TENSION LINK
USER MANUAL
MODEL: EBW-2D
Manual_EBW_V1

USER MANUAL
Box 79 Hantverksvägen 15 Tel. [phone] Web www.vetek.se
76040 Väddö, Sverige Fax [phone] Email [e-mail]
2
TABLE OF CONTENTS
SAFE OPERATION GUIDE-------------------------------------------------------------------------------2
CHAPTER 1 FEATURES AND SPECIFICATION------------------------------------------------3
1 Features---------------------------------------------------------------------------------------------------3
2Main technical data-------------------------------------------------------------------------------------3
3Specification----------------------------------------------------------------------------------------------4
4Appearance illustration--------------------------------------------------------------------------------4
5Power supply------------------------------------------------------------------------------------------ -5
CHAPTER 2 INDICATOR DISPLAY----------------------------------------------------------------5
1Transmitter---------------------------------------------------------------------------------------------5
2 Indicator display ------------------------------------------------------------------------------------- 6
CHAPTER 3 OPERATION GUIDE-----------------------------------------------------------------8
1Turn on/off-------------------------------------------------------------------------------------------------8
2 Zero--------------------------------------------------------------------------------------------------------8
3 Tare---------------------------------------------------------------------------------------------------------8
4Hold--------------------------------------------------------------------------------------------------------8
5Accumulation---------------------------------------------------------------------------------------------9
6 Accumulation Search----------------------------------------------------------------------------------9
7Accumulation Clear-------------------------------------------------------------------------------------9
8 Battery Voltage-------------------------------------------------------------------------------------------9
9 Unit--------------------------------------------------------------------------------------------------------10
10 Return----------------------------------------------------------------------------------------------------10
11 Set Point-------------------------------------------------------------------------------------------------10
CHAPTER 4 PARAMETER SETTING & CALIBRATION-------------------------------------12
1Parameter setting-------------------------------------------------------------------------------------12
2 Calibration----------------------------------------------------------------------------------------------15
CHAPTER 5 DISPLAY ILLUSTRATION-----------------------------------------------------------16
CHAPTER 6 TROUBLESHOOTING GUIDE-----------------------------------------------------17
CHAPTER 7 RS232 PROTOCOL-----------------------------------------------------------------18

USER MANUAL
Box 79 Hantverksvägen 15 Tel. [phone] Web www.vetek.se
76040 Väddö, Sverige Fax [phone] Email inf[email protected]
3
SAFE OPERATION GUIDE
：
1. The capacity of tension link have been showed on the overlay, Don’t make
lifts beyond rated capacity of the tension link.
2. Operators should not maneuver a loaded tension link over personnel.
3.The tension link must be routinely checked for operation. Don’t operate
if shackle, sling, cable, etc show any sign of defects or excessive wear.
4. If the tension link is not going to be used for long time, recharging the battery
every three months to preserve the life-span of the battery and recharge it
before operation.
5. The battery charger is included in the tension link package. Please use this
charger, It’s normal that the charger will become warm when the battery is charging.
6. Please note when the digits flash on the display, it means that the battery needs
to be recharged.
7. Check shackle, safety pins, and latches periodically. Contact your dealer
for parts replacement in case defect, deform or wearing is found.

USER MANUAL
Box 79 Hantverksvägen 15 Tel. [phone] Web www.vetek.se
76040 Väddö, Sverige Fax [phone] Email inf[email protected]
4
CHAPTER 1 FEATURES AND SPECIFICATION
1. Features
◆Wireless communication and display
Wireless indicator, 5 digits LCD display with backlight, Many functions on handheld
indicator
280D. Such as tare, zero, peak, filter setting, gravity regulation.calibration is easy
through
wireless indicator. ,
◆Two set point
Two user programmable Set-Point can be used for safety and warning applications or
for limit weighing.
◆User-friendly design:
Cast alloy steel housing for maximum protection; water proof design, gravity
compensation; safety factor up to 4 times capacity; battery operated with low battery
indication; automatic turn off , power-saving function.
2. Main technical data
Accuracy Standard
According to OIML class III
Indicator Display
25mm(1”) 5digits LCD
Water Proof Class
IP66 (Hand control no IP class)
Zero Range
4% F.S.
Tare Range
100% F.S.
Stable Time
≤5 seconds
Overload Indication
100% F.S. + 9e
Max. Safety Load
125% F.S.
Ultimate Load
400% F.S.
Tension link battery Life
Continous using 90 hours after recharged
Tension link battery type
Standard 18650 Lithium battery,
3.7V/3100mAh
Indicator Battery
SC3300mAh NiH Battery. 1.2Vx4
Tension link Charger
DC4.2V/1000mA
Nominal operating Temp.
- 10℃~ + 40℃
Operating Humidity
≤85% RH under 20
℃
Wireless Distance
100M without obstacle
Wireless Frequency
433MHz

USER MANUAL
Box 79 Hantverksvägen 15 Tel. [phone] Web www.vetek.se
76040 Väddö, Sverige Fax [phone] Email inf[email protected]
5
3. Specification
MODEL
Max.
capacity
(kg)
Min. weigh
(kg)
Division
(kg)
Total display
counts (n)
EBW-5
5000
40
2
2500
EBW-10
10000
100
5
2000
EBW-20
20000
200
10
2000
EBW-30
30000
200
10
3000
EBW-50
50000
400
20
2500
EBW-100
100000
1000
50
2000
EBW-150
150000
1000
50
3000
EBW-200
200000
2000
100
2000
4. Appearance illustration
MODEL
Cap.
(kg)
A
(mm)
B
(mm)
C
(mm)
D
(mm
)
E
(mm)
F
(mm)
G
(mm
)
2-Φ
(mm)
N.W
.
(k )
EBW-5
5000
190
110
60
137
65
30
70
27
2.6
EBW-10
10000
245
110
70
168
65
36
76
41
4.3
EBW-20
20000
312
110
94
206
65
45
85
54
8.5
EBW-30
30000
370
110
114
246
65
50
90
60
14
EBW-50
50000
460
110
140
309
65
60
100
73
25
EBW-10
100000
580
110
180
389
65
80
120
99
53
EBW-15
150000
690
110
220
456
65
90
130
112
89
EBW-20
200000
800
110
250
534
65
100
140
134
128

USER MANUAL
Box 79 Hantverksvägen 15 Tel. [phone] Web www.vetek.se
76040 Väddö, Sverige Fax [phone] Email inf[email protected]
6
5. Tension link power supply
Battery: Standard 18650 Lithium battery, 3.7V/3100mAh
Adapter: Standard 18650 Lithium battery charger
Current: the tension link average current is about DC 30mA±10%, if battery charged, it
can be used for about 90hours.the battery voltge should be between 3.40-4.20, When the
voltage below
3.40, it means the battery needs to be recharged. User can remove the battery cover to
change
new battery, and charge the old battery with adapter.
Charging method: Take out the18650 Lithium battery, put in the charger for charging, the
charge
lamp on the front panel will become orange when charging, and it will become green when
the
charging finish. Generally, charging time should not less than 4hours, it have charging
protection,
long time charging can’t damage the battery.
CHAPTER 2 INDICATOR DISPLAY
1. Tension link transmitter
1. ON/OFF KEY

USER MANUAL
Box 79 Hantverksvägen 15 Tel. [phone] Web www.vetek.se
76040 Väddö, Sverige Fax [phone] Email inf[email protected]
7
When the key is pressed ON, the red light will flash
2. ANTENNA
The antenna is install with water proof connector.
3. Battery cover
User can removed the battery cover to change battery (lithium battery 18650)
2. Indicator display
1. LCD DISPLAY
25mm(1”) 5digits LCD with backlight
2. Signal on LCD
a. : Wireless signal, it Appear means signal stable, it disappear while signal miss. it
flash means signal weak.
b. : Battery Voltage, : Full, : Low, : Empty
c. PEAK：Current value is Peak Hold value(maximum value).
d. MEM：Appear one time when Parameter or calibration value storage. long time
appearance means current value is Accumulation data.
e. STB: Stable Status.
f. kN: “kilonewton”, N：“Newton”. Tare status “N” will flash.
g. t ：“ton”.
h. lb ：“pound”.
i. kg ：“kilogram ”.
3.Key
a. ,
1. Press Key 1 Second, the indicator turn on.
2. In ON status，Press Key 1 Second，the indicator turn off.
b.
1.In testing status ,there are small digits on screen, press this key to obtain the zero
reading.
2.In Parameter Setting status，it used as scrolling down digit.

USER MANUAL
Box 79 Hantverksvägen 15 Tel. [phone] Web www.vetek.se
76040 Väddö, Sverige Fax [phone] Email inf[email protected]
8
c.
1.When there is tare weight such as container, after the reading stable, press this key, it will
display “0”, and “N” indicator Flash.
2. Put the goods into container, the tension link will display goods net weight.
3. If move goods and container, the tension link will display minus value of tare weight.
4. In Parameter Setting status, it used as digits movement.
d.
Used as function shift, or be combined with other keys.
◆Press key once, it display “P0000”, press key , it can
be input password to access parameter setting or calibration status.(refer to
P12 CHAPTER 4)
◆Press key twice, it display “unit”, Press key access unit Setting
status. Press key to select unit (kg,lb,N,kN,t,), After setting finish, press
key to confirm setting and back to test mode.
◆Press key 3 times, it display “SACCU”,Press key to read
accumulate data, it will display “no.xxx” and “Hxxxx”,”Lxxxx”, “no.xxx” means
accumulate numbers, “Hxxxx”,”Lxxxx” means accumulate data, if there is no
accumulate data ,it will display “noACC”, press key back to test mode.
◆Press key 4 times, it display “SEttr”, Press key access pre-tare
value setting. Press key to adjust digit, press key to move digit,
press key again back to test mode. after Pre-tare value setting, the “N”
will flash on LCD.(NOTE: All pre-tare value will set by unit kg)
◆Press key 5 times, it display “dISrU”, Press key will display
tension link voltage, press key back to test mode.
◆Press key 6 times, it display “dISLU”, Press Key will display indicator’s
voltage, press key back to test mode.
◆Press key 7 times, it display “dIS 0”, Press Key will display tension link’s
AD Value.After 2 seconds,it auto back to test mode.
◆Press key 8 times, it display “dISOL”, Press Key will display
“OL=xx” it means tension link’s overload numbers,Press Key back to
test mode.
e. Used as function selection, normally combined with Key.
f.
When load is changing, press this key will catch and display the maximum reading of
the load.
Press this key again, reading will return to normal.( in setting mode it can move digit to
left).

USER MANUAL
Box 79 Hantverksvägen 15 Tel. [phone] Web www.vetek.se
76040 Väddö, Sverige Fax [phone] Email inf[email protected]
9
g.
It is LCD backlight switch. Press once, LCD backlight ON, press again, LCD
backlight OFF.
h.
It is accumulation key,In weighing status press this key will accumulate data(the value
must
be stable and more than 20e)
I.
Press key one time, it will display “CLr 1” Press key to clear single
accumulation value, Press key 2 times, it will display “CLr 2” Press key to
clear all
Accumulation value, Press key 3 times, it will display “CLr 3” Press key to
clear
over load records,
CHAPTER 3 OPERATION GUIDE
Note
：
〖
〗
means the display content
1 TURN ON/OFF
◆Turn on tension link
Press ON/OFF key ,the key light will flash.
◆Turn on indicator( Turn on tension link at first)
OPERATIO
DISPLAY
ILLUSTRATION
〖
88888〗
Display twice, self test
〖
Ert 〗
Display twice
，
abbreviation of Everight
〖
u 2.03〗
Display current software version
〖
5000〗
Display maximum capacity
〖
U=4.80〗
Display current indicator battery voltage
〖
–––––〗
Waiting stable
〖0〗or
〖noSIG〗
If display 0, means the indicator can communicate with the
tension link, if display noSIG, means no si
gnal from tension
link
◆Turn off tension link
Press ON/OFF key when power ON status, ,the key light will not flash
◆Turn off indicator
1 Manual Power OFF Press Key 1 Second
2 Auto Power OFF
The indicator will turn off automatically
after
2 ZERO

USER MANUAL
Box 79 Hantverksvägen 15 Tel. [phone] Web www.vetek.se
76040 Väddö, Sverige Fax [phone] Email inf[email protected]
10
OPERATION
DISPLAY
When tension link turn on, generally tension link
displays〖0〗,if display small digits when no load,
press this key.
Press 〖
0
〗
3 TARE
◆TARE DIRECTLY
OPERATION
DISPLAY
After turn on, hanging tare weight such as sling,
cable at first, press this key, “TARE” light on,
then the tension link will display net weight of
the goods.
1
Press
〖
0
〗
4 PEAK HOLD
OPERATION
ILLUSTRATION
Press
Hold the maximum weight reading when load
changing
Press again
Return to normal weighing status
USER MANUAL 8
ERT10.022 SSE
5.ACCUMULATION
OPERATION
DISPLAY
ILLUSTRATION
Press
〖
No***
〗
Current accumulation time
〖
H****
〗
Front four digits of total value
〖
L****
〗
Rear four digits of total value
After display above contents twice, the tension link will return automatically. maximum
Accumulation times is 999.
6.ACCUMULATION SEARCH
OPERATION
DISPLAY
ILLUSTRATION
Press
key 3 times 〖
SACCU〗
Press
〖
No***
〗
Current accumulation time
〖
*****
〗
Current weight reading
〖
H****
〗
Front four digits of total value
〖
L****
〗
Rear four digits of total value
Press
key again
Return
Press key can check different times weight and accumulation.
7. ACCUMULATION CLEAR