Vibrant Health & Wellness super vibe 2000 User manual

SUPER VIBE 2000 USER MANUAL
GET FIT & STAY
HEALTHY IN
JUST 10 MINUTES
A DAY!

2© Vibrant Health & Wellness, Inc.
Table of Contents
Introduction...............................................................3
Safety Precautions ...................................................4
Assembly Instructions............................................6
Operating Instructions...........................................7
Getting Started ...................................................... 10
User Guidelines...................................................... 11
Maintenance........................................................... 13
Troubleshooting.................................................... 14
Warranty/Guarantee ............................................ 15
Toll Free [phone]

3
FULL BODY VIBRATION | SUPER VIBE 2000 USER MANUAL
Congratulations on the purchase of your new Vibrant Health & Wellness Full Body
Vibration (also known as Whole Body Vibration) exercise machine. Our Full Body
Vibration (FBV) machines provide maximum health and tness benets comparable
to strenuous resistance exercises such as weight lifting, Pilates, and yoga–but with
less time, eort, and stress on the body. Increased strength, reduced body fat, and
lean muscle mass are some of the reasons we suggest you should use your FBV
machine to make a positive improvement in your tness regimen!
FBV is one of the safest, most eective, and easiest exercise machines presently
available. Its applications range from top-of-the-line tness conditioning to total
body wellness and rejuvenation. In just 10 to 20 minutes a day, three to ve times a
week, a new level of health and wellness and sports performance may be obtained.
Please read through our manual carefully to learn how to properly use your
FBV machine to achieve maximum benets. You may also visit our website at
www.fullbodyvibration.com to receive ongoing support and access other useful
information. Regular updates will be added as they become available.
How does vibration technology work?
In traditional power and strength training, the load on the muscles is determined
by the amount of weight being lifted. When using the vibration machine, a specic
frequency and amplitude of vibration is chosen and the movement of the platform
loads the muscles. This stimulates a reex contraction within the muscle, which in
turn leads to a high level of muscle activation and exertion. The superior muscle
activation that is caused by the vibration machine, as compared to conventional
training, means that less time is required to work muscle groups completely. The
benets may be wider ranging than those achieved by ordinary exercise.
How can Full Body Vibration benet you?
There are numerous scientic research studies on the eects of vibration exercise.
Some of the ndings are published in leading medical research journals, including the
US National Library of Medicine www.pubmed.gov. Research studies also may be found
at www.fullbodyvibration.com. The FDA has not evaluated these studies.
Introduction

4© Vibrant Health & Wellness, Inc.
Safety Precautions
CAUTION: For an extensive list of precluding ailments, please refer to the section on the
following pages entitled "Who should use safety precautions?" If you experience any
physical discomfort or abnormalities while using the FBV machine, stop immediately and
consult a physician.
KEEP OUT OF REACH OF CHILDREN: This machine is not intended to be used by or near
children. It is the user’s responsibility to keep children, pets, and incapacitated persons
away from the machine when it is in use or left unattended.
Danger: Do not allow hair or loose-tting clothing near the base (vibration platform) of
the machine during operation to prevent any possible entanglement with moving parts.
Take extra CAUTION to avoid ngers, hands, feet, or toes from getting caught in the
openings around the vibration platform.
Do not operate if the unit has a damaged cord or plug, the unit has been dropped or
damaged, exposed to liquids or moisture, or is malfunctioning in any way. If your machine
has any physical malfunctions, contact Vibrant Health & Wellness for repairs and/or
warranty issues.
The machine must be grounded or there is a danger of electrical shock. It is equipped
with a cord with a grounding conductor and a grounded plug. The electrical outlet it is
plugged into must be properly installed and grounded in accordance with all local codes
and regulations. IF THERE IS ANY DOUBT, CONSULT AN ELECTRICIAN.
Do not operate on the same circuit as any other appliance. If the cord or plug is damaged,
DO NOT attempt to replace or repair it yourself. This must be done by an authorized
service center or electrician. Never attempt to modify the cord or plug. Do not use any
parts that are not recommended by the manufacturer.
Do not use within 30 minutes after meals. Remember to drink plenty of water before and
after exercising.

5
FULL BODY VIBRATION | SUPER VIBE 2000 USER MANUAL
Safety Precautions (continued)
Never allow more than one person on the vibration platform at any time. Doing otherwise
may cause personal injury or damage to the machine.
It is recommended when standing on the vibration platform to wear closed-toe shoes.
(Exercise shoes such as gym shoes or sneakers are preferred.)
Avoid all contact with water (including wet hands) while using the machine to eliminate any
risk of electrical shock. Do not use outdoors or expose the unit to atmospheric conditions
such as direct sunlight, rain, fog, mist, or hail.
Turn o power to the machine after each use by turning o the main power switch on the
base unit located above the electrical cord.
Never leave the machine unattended when it is plugged into an electrical outlet.
When not in use, unplug the power cord from the electrical outlet. To unplug the power
cord, turn the power switch to the o (O) position and then remove the power cord from the
electrical outlet.
Disclaimer: Full Body Vibration is not intended to diagnose, treat, or cure any disease.
Who should use safety precautions? Most adults from the physically t to the sedentary can
use FBV. While the following list of medical conditions is not complete and FBV is extremely
smooth and gentle, we strongly advise that you consult with your physician before using
FBV if any of the listed conditions apply to you. This does not mean that if you are
suering from any of the conditions on the list that you cannot use FBV. Vibration
therapy has been studied and used by professional entities around the world, in a number
of cases, it is highly recommended to integrate vibration training in a treatment plan under
the medical advice of a doctor, specialist, or physiotherapist. These conditions include, but
are not necessarily limited to pregnancy, pulmonary embolism, acute hernia, discopathy,
spondylosis, acute thrombosis, severe diabetes, known neurological conditions, migraines,
epilepsy, pre-existing deep vein thrombosis, cardiovascular disease, recent infections,
pacemaker and implantable cardioverter debrillators, those undergoing cancer treatments
(chemotherapy/radiation) or who have tumors, known retinal conditions, recently placed
IUDs, metal pins or plates, are recently recovering from an operation or surgery such as a hip
or knee replacement, have recent operative wounds, or have poor somatosensory receptor
sensitivity on the plantar surfaces of their feet. If you are experiencing other symptoms, brief
or long-term conditions, or are on medication, consult your physician prior to engaging in
FBV use.

6© Vibrant Health & Wellness, Inc.
Unpack the Super Vibe 2000 and verify that all contents are present and undamaged.
Contents include Exercise Chart, User Manual, Pair of Handles with 4 Screws and Washers,
3-Piece Pipe Set, Center Bolt and Knob, (2) T-Bolts, Allen Wrench, Power Cord, Remote
Control, Yoga Mat, and Base Unit with 5 Feet and Locking Wing Nuts.
ALWAYS DISPOSE OF PACKAGING CAREFULLY AND KEEP OUT OF REACH OF CHILDREN.
PLASTIC BAGS AND FOAM PIECES MAY POSE SUFFOCATION OR CHOKING HAZARDS.
Feet and Locking Wing Nut Assembly:
1. Adjust each foot, if necessary, to ensure that all ve feet
make rm contact with the oor surface. Note: The locking
wing nut must be securely fastened against the frame
to ensure the tightness of each foot. (Loose feet or wing
nut adjustments may cause malfunction or noise during
operation.)
Handle Assembly:
1. Attach the 3-piece pipe set by loosely connecting the
center pipe to the center base bracket by using the
center bolt and knob supplied. (See diagram 1.)
2. After the center bolt is loosely fastened through the
center pipe and the center base bracket, attach the two
outer pipes to the base brackets one at a time by loosely
fastening the t-bolts through each side. (See diagram 2.)
IMPORTANT: When attaching the two outer pipes onto
the base brackets, loosely fasten the t-bolts through the
pipe and the base bracket a few turns until both outer
pipes are aligned and loosely attached. When all three
pipes are loosely attached to the base brackets, hand
tighten all bolts to rmly secure the 3-piece pipe set onto
the base unit.
3. Insert the handle pipes into the 3-piece pipe set by using
the screws and washers provided (2 screws and washers
for each pipe; see diagram 3).
Assembly Instructions
3
2
1
Center Bolt and Knob T-Bolts
Machine Foot with Locking Wing Nut

7
FULL BODY VIBRATION | SUPER VIBE 2000 USER MANUAL
Operating Instructions
Control Screen Display and Button Description:
Button Description
User-Dened Program
Time Up
Time Down
Start/Stop
Mode Selection
Left: Oscillation Speed Up
Right: Spiral Speed Up
Left: Oscillation Speed Down
Right: Spiral Speed Down
Starting the machine in Manual Mode:
This feature is suggested for beginners and for people who want to control the speeds
manually. The Manual Mode function is activated by pressing the START/STOP button
located on the remote control or on the base control panel of the machine. This is a default
setting each time you start the machine with the START/STOP button.
When the machine rst turns on in Manual Mode: Both motors will start at their lowest
speeds (01/01) and the timer will automatically begin a 10-minute countdown.
To operate only one motor: You must turn o the motor that you do not want to operate
by pressing the - button. Press the + button to turn on the motor that you want to increase.
By pressing/holding the + or – button while pointing the remote at the control screen, the
speeds will increase or decrease. You may operate the motors independently or together at
the same or dierent speeds.

8© Vibrant Health & Wellness, Inc.
Operating Instructions (continued)
Operating Programs:
To select any of the desired programs, press the MODE button. The control screen will
display P1. By continuing to press the MODE button, the control screen will display P2,
P3, U1, U2, U3, and Manual. P1, P2, and P3 are automatic programs. U1, U2, and U3 are
User-Dened Programs (See Programs below). After selecting a desired program, press the
START/STOP button. The machine will start and operate on the selected program.
Automatic Programs:
There are three preset programs: P1, P2, and P3. These programs are optional and based
on desired choice. Each program has its own preset variation of speeds and duration times
that uctuate during the 10-minute default operating time.
User-Dened Programs:
There are three user-Dened Programs: U1, U2, and U3, which allow you to design and
customize personal programs of your choice. Each program allows you to enter up to
12 variations of speeds and duration times of each spiral and oscillation feature. Once
a designed cycle has completed, the machine will automatically advance to the next
programmed variation within the selected User-Dened Program. These cycles will
continue for 10 minutes (the maximum time the machine will run in automatic or User-
Dened Program mode). Once designed and programmed, the machine stores your
personal preferences permanently until you choose to change them.
REMOTE CONTROL USER INSTRUCTIONS:
Display Light: The light ickers when you press any button
on the remote control.
Note: When operating the remote control, the sensor on the
front (nose) of the remote control must be pointed at the control
screen on the base unit when pressing the buttons.
Start: Press the START/STOP button to start the machine.
Speed Adjustment Button (Manual Mode only):
•Press left + button to increase the oscillation speed.
•Press left – button to decrease the oscillation speed.
•Press right + button to increase the spiral speed.
•Press right – button to decrease the spiral speed.
Note: By pressing/holding the + or – button while pointing the remote
control at the control screen, the speeds will increase or decrease.
Stop: Press the START/STOP button to stop the machine.
Time Adjustment Button (Manual Mode only): Press TIME+/TIME– button to adjust the
desired time. (Not for automatic programs.) The default time setting is 10 minutes.
ed
)
o
l
remot
e
s
e.
/
TIME– button to ad
ju
st the
ting is 10 minutes.
e
Remote Control

9
FULL BODY VIBRATION | SUPER VIBE 2000 USER MANUAL
Following are instructions for adding and changing the User-Dened Programs.
Programming instructions for U1, U2, and U3 are identical. Before starting the machine,
press the MODE button until U1 appears on the display. Next press the USER-DEFINED
PROGRAM button on the base of the machine and U1 will begin ashing. A bar will
appear above both the and . You may now begin programming the rst cycle of
U1. Press the left button to set the oscillation speed. The speed selected will be shown
on the left of the screen display. Press the right button to set the spiral speed. The
speed will be shown on the right of the screen. Speeds selected may range from 0 to 60
(selecting 0 means the corresponding motor will not run during that cycle of the program).
Press the TIME UP or TIME DOWN button to set the running time for the cycle. The time
selected will appear on the display, e.g., 20 seconds will appear as Time 20. Press the USER-
DEFINED PROGRAM button on the base of the machine. This records the programming
information you have selected in cycle 1 and advances to cycle 2 within the U1 program.
You may continue to program up to 12 cycles using the procedure described above, or you
may skip subsequent cycles by pressing the USER-DEFINED PROGRAM button on the
base of the machine until U1 stops ashing.
To change an ENTIRE program, locate the User-Dened Program that you desire by
pressing the MODE
p
p
p
p
button until it appears, and then repeat the instructions in the
previous paragraph. Remember, if you have programmed 12 cycles within a program, you
must change each one individually. To CHANGE ONLY SELECTED CYCLES within a program,
press the USER-DEFINED PROGRAM button on the base of the machine until your
program cycle appears and then make your changes as described above. Press the USER-
DEFINED PROGRAM button again to record your changes.
Note:
a. The programming of U2 and U3 is the same process as the programming of U1.
b. The program will repeat automatically until the total system time is nished, and
then it will stop.
c. You can press the START/STOP button to stop the machine at any time. The
system will return to the Manual Mode. You can press the MODE button to
choose the program at this time and press the START/STOP button to run it.
d. During operation, you can press the START/STOP button at any time to stop it.
e. During the running of U1, U2, and U3, only the START/STOP button is active.
Operating Instructions (continued)

10 © Vibrant Health & Wellness, Inc.
Getting Started
How you decide to use your vibration exercise machine depends on your own personal
preference. You can simply nd a single position that is most comfortable for you, or
you can perform a variety of positions for selected periods of time–the decision is up to
you. We suggest starting SLOWLY (See User Guidelines) until you become more adapted.
You may use both motors together or use one motor by itself. When using two motors
together, they do not have to be on the same speeds. (See Operating Instructions.)
Floor Surface to Use the Vibration Machine
Carpet or Hard Floor: Your machine may be used on carpet or hard oor surfaces. The
machine does not produce heat and is safe for all oor surfaces. It is important that all
machine feet are rmly touching the oor. On hard oors, we recommended using a non-
slip, thin carpet or mat beneath the machine to ensure rm contact.
User Tips
In order to maximize the desired results from your new FBV machine, a few tips are
suggested.
When standing on the machine platform (prior to starting the machine), position your
feet straight and evenly apart (about shoulder width), keeping toes pointed forward and
keeping a slight bend in your knees.
Do not use the vibration machine in any one position for more than 10 minutes during any
one session.
It is VERY important that the center of the platform is centered between your feet at all
times. Positioning your feet away from the center of the platform will increase amplitude.
Positioning your feet closer toward the center of the platform will decrease amplitude.
FBV exercise depends on both the frequency and intensity of the vibrations. The higher
the amplitude, the more the muscles contract in order to appropriately adjust to the
mechanical movement of the platform. This increase in amplitude can lead to a more
powerful eect in some circumstances. FBV exercise may stimulate up to 100 percent of
the body’s muscle bers.

11
FULL BODY VIBRATION | SUPER VIBE 2000 USER MANUAL
User Guidelines
User Weight Capacity: 265 lbs.
How often can I use the vibration machine? Based on your physical condition and
individual preference, you may use the machine every day and multiple times throughout
the day. Do not use the vibration machine in any one position for more than 10 minutes
during any one session.
How do I know which speed setting is right for me? We highly suggest that each user
nd gentle speeds and time frames that are safe and comfortable for his or her body.
Low Oscillating Speeds: (01–15) Low speeds within this range are suggested for beginning
exercisers, new FBV users, and those who are frail, debilitated, overweight, or not in good
physical condition.
We suggest that those beginning an exercise program and new users start by using
slow speeds for short periods of time until the body and muscles adapt to the oscillation
movement. Low speeds are suggested for weight loss, body fat reduction, and for those
with poor balance.
Medium Oscillating Speeds: (16–30) Medium speeds are suggested for intermediate
exercisers and those who are in good physical condition. These speeds may be for people
who have become comfortably adapted to low speeds. Medium speeds are suggested
for muscle tone, core strength, and those with poor circulation. Medium speeds are not
recommended for weight loss or body fat reduction.
High Oscillating Speeds: (31–60) High speeds are suggested for advanced exercisers
who are physically t or want high-impact sports training. High speeds may have
benets equivalent to the medium speeds and may be used by those who have become
comfortably adapted to low and medium speeds and want to increase the intensity of their
sessions. High speeds are not recommended for weight loss and body fat reduction.
Spiral Vibration Speeds: (01–60) Spiral Vibration, also called“The Massage CirCulizer,”is
extremely smooth and gentle. This circular/orbital movement oers ultimate comfort
by creating body stimulation without causing the body to sway or jostle. This spiral
movement is considered to be the most gentle and smoothest feature in the vibration
industry. This spiral feature is suggested for those with poor circulation, low energy, or
those who suer from pain and who may not want to use oscillation. Each user can select a
smooth, gentle speed that feels comfortable to his or her body.

12 © Vibrant Health & Wellness, Inc.
You may decide to use the machine every day, but that depends upon your tness condition
and personal choice.
Below are some illustrations of positions that may target dierent muscle groups of the
body.
User Guidelines (continued)

13
FULL BODY VIBRATION | SUPER VIBE 2000 USER MANUAL
Maintenance
A periodic check of your vibration machine will help keep your machine in good operating
condition and may also help prevent potential problems in the future. The following is
recommended:
•Always unplug the power cord from the electrical outlet before cleaning, performing
any kind of maintenance, and when the machine is not in use.
•Tighten all screws every few months.
•Adjust the feet if the machine is not level.
•Do not use harsh chemical cleaners, solvents, or any ammable liquids to clean the
machine.
•Wipe the platform and support handles with a clean cloth after each use to prevent
perspiration from entering the machine.
•After each use, turn o the power switch located on the base unit and unplug the
power cord from the electrical outlet.
Do not store the machine under these conditions:
•Near heat or open ame
•Under direct sunlight
•In a humid environment
If the machine is not in use for long periods of time, cover it with a clean soft cloth.
Also, do not twist the cord as this may cause the machine to malfunction.
Features & Specications
Vibration Type: Oscillation & Spiral/Orbital
Motor Power: 200 W & 200 W DC
Oscillation Amplitude: 0–8 mm
Oscillation Frequency: 5–15 Hz
Spiral Amplitude: 0–2 mm
Spiral Frequency: 15–40 Hz
Control Panel: LCD Screen on Base with Separate Remote Control
Speed Range: 0–60
User Weight Capacity: 265 lbs
Unit Weight: 67 lbs
Unit Size: L 22 in. x W 21.6 in. x H 42.5 in.
Input Voltage: AC 110–120 V/60 Hz
Certication: CE, ISO, ROS, Issued by SGS

14 © Vibrant Health & Wellness, Inc.
Troubleshooting
1. Problem: Machine makes rattling noise.
Solution:
A. Check for loose feet and/or loose locking wing nuts on the feet and tighten.
B. Check handle screws and all exterior screws and tighten.
2. Problem: Machine runs intermittently or doesn’t respond to control operation.
Solution:
(Turn o the power switch located by the power cord and unplug the power
cord for 10 seconds. Plug the cord back in, turn the power switch back on,
and start the machine.
3. Problem: Remote Control doesn’t respond.
Solution:
A. The remote control front nose must be pointed at the control panel on the
machine. (Point at the center of the control panel screen.)
B. Press any button on the remote control and see if the red light ickers. (If so,
the remote control is working.)
C. If the red light on the remote control ickers and there is no response,
"reboot" the machine (see # 2 above).
D. If the red light on the remote control doesn't icker when pressing any
button, spin the batteries to ensure better contact or replace the batteries.
4. Problem: Machine does not turn on (no power to switch or control screen).
Solution:
A. Check the power cord and make sure it is securely pushed all the way into
the plug receptacle of the machine.
B. Check the wall plug to make sure the power is working through the wall
socket. (Plug in a small lamp to test.)
C. Check the power switch and ensure that the switch is in the ON ( I ) position.
D. Check the fuse inside the fuse holder located at the bottom of the plug
receptacle on the base unit.
Note: The plug must be removed from the plug receptacle of the machine to
extract the fuse holder and the fuse.
DO NOT open the machine cover, disassemble, or unscrew any components from the
base unit without instructions from the company.
For ALL service needs, contact customer service at [phone].

15
FULL BODY VIBRATION | SUPER VIBE 2000 USER MANUAL
Warranty/Guarantee
1 Year FULL Warranty with 5-Year Motor
Vibrant Health & Wellness warrants its vibration machines to be free of any defects in
materials and workmanship. If the vibration machine exhibits any defects while being operated
correctly and within the guidelines provided during the period of one (1) year from the date
the machine was received, Vibrant Health & Wellness will either repair or replace the defective
part or the machine. Motors are under warranty for a period of ve (5) years from the date the
machine was received.
This warranty does not cover the following:
•Damage, accidental or otherwise, to the vibration machine not caused by direct defects
from factory workmanship or materials.
•Damage due to abuse, mishandling, alteration, misuse, or failure to follow suggested use
and maintenance.
•Damage caused by parts or service not authorized or performed by an authorized agent
of Vibrant Health & Wellness.
Please do not send your Vibrant Health & Wellness Full Body Vibration machine back without
return authorization. Please contact us at 1-855-All Vibe [phone] to arrange handling
and warranty logistics.
You are responsible for arranging and paying the charges to ship the machine back to Vibrant
Health & Wellness, and we will repair or replace the machine and send it back to you at our cost.
Under any circumstance, our liability shall not exceed the retail cost of the vibration machine.
Please save your original shipping box(es) and inserts as they have been specically designed
to handle the product and minimize the risk of damage during shipping.

www.fullbodyvibration.com
Toll Free 855-All-Vibe [phone]