Vicon VM615-4 User manual

Installation & Operation Manual
XX108
MODEL VM615-4
HIGH-RESOLUTION COLOR MONITOR
Copyright © 2002 Vicon Industries Inc. All rights reserved.
Product specifications subject to change without notice.
Vicon and its logo are registered trademarks of Vicon Industries Inc.
VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAUGE, NEW YORK 11788
TEL: 631-952-CCTV (2288) FAX: 631-951-CCTV (2288) TOLL FREE: 800-645-9116
24-Hour Technical Support: 800-34-VICON (800-348-4266)
UK: 44/(0) 1489-566300 INFOFAX: 800-287-1207 WEB: www.vicon-cctv.com
Vicon part number 8009-8108-00-00 Rev 302 Section 3
0) VM615-4-cover 4/9/02 1:33 PM Page 2

1) VM615-4 E 4/9/02 1:33 PM Page 1

Graphic Symbol Explanation
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the presence
of uninsulated ‘dangerous voltage’ within the product’s
enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
Warning - To Prevent Fire or Shock Hazard, Do Not
Expose This Monitor To Rain or Moisture.
ii
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
1) VM615-4 E 4/9/02 1:33 PM Page ii

IMPORTANT SAFEGUARDS
Caution
Power source is indicated on the rear of the set. It contains high-voltage parts. If
you remove the cover, it may cause fire or electric shock. Do not remove the
cover by yourself. (Control switches are at the front of the monitor.)
1. Read Instructions : All the safety and operating instructions should be
read before the appliance is operated.
2. Retain Instructions : The safety and operating instructions should be
retained for future reference.
3. Heed Warnings : All warnings on the monitor and in the operating
instructions should be adhered to.
4. Follow Instructions : All operating and use instructions should be
followed.
5. Cleaning : Unplug this monitor from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
Exception. A monitor that is meant for uninterrupted service and that
for some specific reason, such as the possibility of the loss of an
authorization code for a CATV converter, is not intended to be
unplugged by the user for cleaning or any other purpose, may exclude
the reference to unplugging the monitor in the cleaning description
otherwise required in Item 5.
6. Attachments : Do not use attachments not recommended by VICON as
they may cause hazards.
7. Water and Moisture : Do not use this monitor near water, for example,
near a bathtub, wash bowl, kitchen sink, or laundry tub, in a wet
basement, or near a swimming pool and the like.
iii
1) VM615-4 E 4/9/02 1:33 PM Page iii

8. Accessories : Do not place this monitor on an unstable cart, stand,
tripod, bracket, or table. The monitor may fall, causing serious injury to
a child or adult, and serious damage to the appliance. Use only with a
cart, stand, tripod, bracket, or table recommended by VICON, or sold
with the monitor. Any mounting of the monitor should follow VICON’s
instructions, and should use a mounting accessory recommended by
VICON.
9. Ventilation : Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the monitor and to protect
it from overheating, and these openings should never be blocked by
placing the monitor on a bed, sofa, rug, or other similar surface. This
monitor should never be placed near or over a radiator or heat register.
This monitor should not be placed in a built-in installation such as a
bookcase or rack unless proper ventilation is provided or VICON’s
instructions have been adhered to.
10. Power Sources : This monitor should be operated only from the type of
power source indicated on the label. If you are not sure of the type of
power supply to your installation site, consult your VICON dealer or
local power company.
11. Grounding or Polarization : For monitors equipped with a 3-wire
grounding-type plug having a third (grounding) pin, this plug will only
fit into a grounding type power outlet. This is a safety feature. If you are
unable to insert the plug into the outlet, contact your electrician to
replace your obsolete outlet. Do not defeat the safety purpose of the
grounding-type plug.
12. Power : Cord Protection-Power supply cords should be routed so that
they are not likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the monitor.
iv
1) VM615-4 E 4/9/02 1:33 PM Page iv

13. Lightning : For added protection for this monitor during a lightning
storm, or when it is left unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the cable system. This will
prevent damage to the monitor due to lightning and power-line surges.
14. Overloading : Do not overload wall outlets and extension cords as this
can result in a risk of fire of electric shock.
15. Object and Liquid Entry : Never push objects of any kind into this
monitor through openings as they may touch dangerous voltage points
or short-out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the monitor.
16. Servicing : Do not attempt to service this monitor yourself as opening
or removing covers may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.
17. Damage Requiring Service : Unplug this monitor from the wall outlet
and refer servicing to qualified service personnel under the following
conditions.
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the monitor.
c. If the monitor has been exposed to rain or water.
d. If the monitor does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the
operating instructions as an improper adjustment of other controls
may result in damage and will often require extensive work by a
qualified technician to restore the monitor to its normal operation.
e. If the monitor has been dropped or the cabinet has been damaged.
f. When the monitor exhibits a distinct change in performance-this
indicates a need for service.
v
1) VM615-4 E 4/9/02 1:33 PM Page v

18. Replacement Parts : When replacement parts are required, be sure the
service technician has used replacement parts specified by VICON or
have the same characteristics as the original parts.
Unauthorized substitutions may result in fire, electric shock or other
hazards.
19. Safety Check : Upon completion of any service or repairs to this
monitor, ask the service technician to preform safety checks to
determine that the monitor is in proper operating condition.
FCC & ICES Information
Warning
This equipment has been tested and found to comply the limits for a class A
digital device, pursuant to part 15 of the FCC Rules and ICES-003 of
Industry Canada. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial
environment. This equipment generate, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct
the interference at his own expense.
User-Installer Caution
Your authority to operate this FCC verified equipment could be voided if
you make changes or modifications not expressly approved by the party
responsible for compliance to part 15 of the FCC Rules.
vi
1) VM615-4 E 4/9/02 1:33 PM Page vi

General
Scope
The information in this instruction manual covers the installation and
operation of the VM615-4 Color Monitor.
These units should be installed using approved materials and wiring
practices in accordance with the National Electrical Code and applicable
local wiring ordinances.
Introduction
The VM615-4 Color Monitor, having a resolution of more than 650 lines at
center, produces high quality pictures on a 15” (measured diagonally) screen.
Designed primarily for industrial applications this monitor accepts standard
NTSC/PAL color input signals.
Operating controls (BRIGHT, CONTRAST, COLOR, TINT, SHARP,
VOLUME) are located on the front panel. A power switch is also located on
the front panel.
A regulated power supply maintains excellent performance during
fluctuations in line voltage.
The VM615-4 Color Monitor is housed in a metallic dark-gray color cabinet.
vii
1) VM615-4 E 4/9/02 1:33 PM Page vii

1) VM615-4 E 4/9/02 1:33 PM Page viii

Before operating the unit, please read this manual thoroughly,
and retain it for future reference.
1) VM615-4 E 4/9/02 1:33 PM Page e-1

e-2
Contents
IMPORTANT SAFEGUARDS .............................................. iii
General ................................................................................... vii
Specifications ........................................................................ e-3
Front Panel Components and Controls ................................. e-4
Rear Panel Components and Controls .................................. e-6
Connections .......................................................................... e-7
Maintenance .......................................................................... e-8
1) VM615-4 E 4/9/02 1:33 PM Page e-2

Specifications
System NTSC/PAL
CRT 15” diagonal, 0.28 mm Dot Pitch.
90 ° deflection
Horizontal Resolution more than 650 lines
Input Signal Video A/B : Composite 1 Vp-p
Video C : S-VHS
Subcarrier 3.579545 MHz ± 400 Hz (room temperature)
Frequency Sync. Range 4.433618 MHz ± 400 Hz (room temperature)
Horizontal 15.75 kHz ± 500 Hz
Frequency Stability 15.625 kHz ± 500 Hz
Vertical 60 Hz ± 5 Hz
Frequency Stability 50 Hz ± 5 Hz
High Voltage 25 kV ± 1.5 kV
Convergence less than 0.3 mm (at the center of display area)
Power Consumption 85 Watts (maximum)
Operating Humidity 0 to 90% (non condensing)
Condition
Operating Temperature 32 °F to 104 °F (0 to 40 °C)
Range
Power Control range or main section 90 V~260 V or
“indicated on the rear of the Monitor cover case”
Dimensions (WxDxH)
14.4 x 13.5 x 15.4 inches / 365 x 342 x 391 mm (without packing)
Weight Approx. 31 lbs / 14 kg (with packing)
Audio 1.0 Watts
e-3
1) VM615-4 E 4/9/02 1:33 PM Page e-3

Front Panel Components and Controls
POWER Switch
Power on switch. If you press this button, the monitor is turned on and the
LED of selected input signal is lit.
VIDEO Input Selection Switch
It selects video and audio input signal. To change input signal, press this
button.
VOLUME, DATA Control Switch
VOLUME key has two functions :
• Volume Controls: To raise or lower volume, press one of these keys,
▲ to raise, ▼to low.
• Data Controls: If you press CONTRAST, BRIGHT, COLOR, TINT
or SHARP and then VOLUME keys, you can change
the value those characteristics.
e-4
SHARP TINT COLOR BRIGHT CONTRAST VOLUME
DATA
A
B
C
VIDEO POWER
POWER
VIDEO
VOLUME
DATA
1) VM615-4 E 4/9/02 1:33 PM Page e-4

CONTRAST Switch
This control adjusts the contrast of the screen image. Press CONTRAST
switch and then VOLUME (DATA) switch to control the contrast.
(Default is 60.)
BRIGHT Switch
This control adjusts the brightness of the screen image. Press BRIGHT
switch and then VOLUME (DATA) switch to control the brightness.
(Default is 50.)
COLOR Switch
This control adjusts the color intensity of the screen image. Press COLOR
switch and then VOLUME (DATA) switch to control the color intensity.
(Default is 50.)
TINT Switch
With this switch, you can control the color to be close to natural color.
For the best result, control screen image with this switch so that skin color is
natural. Press TINT switch then VOLUME (DATA) switch to control the
color. (Default is 50.)
SHARP Switch
This control adjusts the sharpness of the screen image. Press SHARP switch
and then VOLUME (DATA) switch to control the sharpness. (Default is 50.)
e-5
COLOR
TINT
SHARP
CONTRAST
BRIGHT
1) VM615-4 E 4/9/02 1:33 PM Page e-5

Rear Panel Components and Controls
VIDEO LINE
Input/output terminals for video signal.
Video A and Video B are composite input/output terminals.
Video C is S-VHS input/output terminals.
AUDIO LINE
Input/output terminals for audio signal.
A, B, and C must be selected with Video A, Video B, Video C respectively.
e-6
IN
Video A
OUT IN
Video B
OUT IN
Video C
OUT
VIDEO LINE AUDIO LINE
A
B
C
IN OUT
1) VM615-4 E 4/9/02 1:33 PM Page e-6

Connections
e-7
IN
Video A
OUT IN
Video B
OUT IN
Video C
OUT
VIDEO LINE AUDIO LINE
A
B
C
IN OUT
Rear panel of MONITOR
CCD Camera
S-VHS CCD Camera
S-VHS VCR
VCR
1) VM615-4 E 4/9/02 1:33 PM Page e-7

Maintenance
If the quality of the picture on the VM615-4 Color Monitor is poor and
cannot be improved, inspect all system connections and cable runs.
Repairs should be performed by a qualified technician with adequate test
equipment and facilities.
e-8
1) VM615-4 E 4/9/02 1:33 PM Page e-8

Avant d’utiliser cet appareil, lisez ce manuel entièrement,
et gardez-le pour la référence de futur.
2) VM615 -4 F 4/9/02 1:33 PM Page f-1

Explication des symboles graphiques
La flèche en forme d’éclair, représentée dans un triangle
équilatéral signale la présence d’une haute tension électrique
dangereuse á l’intérieur de l’appareil.
Le point d’exclamation, représenté, dans un triangle
équilatéral, vous signale des instructions importantes
concernant le produit.
Avertissement - Pour Prevenir Le Risque D’incendie Ou De
Decharges Electriques, Evitez Tout Contact
Du Moniteur Avec L’eau Ou L’humidite.
f-2
PRÉCAUTION : POUR REDUIRE LE RISQUE D’ÉLECTROCUTION, NE SORTEZ
PAS LE COUVERCLE (OU PARTIE ARRIÈRE). IL N’YA A PAS
DE PIÈCES À L’UTILISATION DE L’USAGER. APPELEZ LES
SERVICES DU PERSONNEL DE SERVICE QUALIFIÉ.
RISQUE D’ÉLECTROCUTION,
N’OUVREZ PAS
PRÉCAUTION
Cet appareil numérique de la classe A est conforme à la norme
NMB-003 du Canada.
2) VM615 -4 F 4/9/02 1:33 PM Page f-2

INFORMATION DE SÉCURITÉ
Attention
Ce moniteur fonctionne sur l’alimentation électrique indiqueée sur la plaque á
l’arrière du coffret. Il contient des piéces sous haute tension. Si vous retirez le
couvercle, if y a des risques d’incendie ou d’électrocution. Ne retirez pas le
couvercle vous-même(Les boutons de commande sont situés à l’avant du
moniteur.)
1. Connaissances requises : Avant d’utiliser le moniteur, il est
recommandé de lire les consignes de sécurité et les instructions
d’utilisation.
2. Conservation du mode d’emploi : Les consignes de sécurité et les
instructions d’utilisation doivent être conservées en lieu sûr pour
consultation ultérieure.
3. Avertissement : Vous devez tenir compte des avertissements apacés sur
le moniteur et dans le mode d’emploi.
4. Instructions d’utilisation : Vous devez vous conformer aux instrictions
d’utilisation fournies.
5. Nettoyage : Débranchez le moniteur de la prise secteur avant de le
nettoyer. N’employez pas de nettoyant liquide ou en aérosol, mais un
simple chiffon humide.
Exception. L’obligation de débrancher le moniteru avant nettoyage,
précisée à l’alinéa 5, peut être ignorée dans le cas d’un moniteur conÿu
pour une utillsation constante, qui ne doit pas être éteint pour une raison
spécifique, telle que pour éviter la perte d’un code d’autorisation
d’accès à un convertisseur CATV.
f-3
2) VM615 -4 F 4/9/02 1:33 PM Page f-3