Vicon V682-PTZ User manual

User Guide
V682-PTZ
Outdoor Analog PTZ Dome Camera
XX307-20-00
Vicon Industries Inc. does not warrant that the functions contained in this equipment will
meet your requirements or that the operation will be entirely error free or perform precisely as
described in the documentation. This system has not been designed to be used in
life-critical situations and must not be used for this purpose.
Document Number: 8009-8307-20-00 Product specifications subject to change without notice.
Issued: 6/2021 Copyright © 2021 Vicon Industries Inc. All rights reserved.
Vicon Industries Inc.
Tel: [phone]) Fax: [phone]
Toll Free: 800-645-9116
24-Hour Technical Support: 800-34-VICON
(800-348-4266)
UK: 44/(0) 1489-566300
www.vicon-security.com

2
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO
NOT INSERT ANY METALLIC OBJECTS THROUGH THE
VENTILATION GRILLS OR OTHER OPENINGS ON THE
EQUIPMENT.
CAUTION
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to
the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.

3
FCC COMPLIANCE STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC INFORMATION: This equipment has been tested and found to
comply with the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference
to radio communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
CAUTION: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003
du Canada.
CE COMPLIANCE STATEMENT
WARNING
This is a Class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.

4
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves,
or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding
type plug has two blades and a third grounding prong. The wide blade or the
third prong is provided for your safety. If the provided plug does not fit into
your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plug’s,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when
the apparatus has been damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
15. CAUTION – THESE SERVICING INSTRUCTIONS ARE FOR USE BY
QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF
ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN
THAT CONTAINED IN THE OPERATING INSTRUCTIONS UNLESS YOU
ARE QUALIFIED TO DO SO.
16. Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed
Class 2 power source only.

5
Contents
Chapter 1 — Introduction..................................................................................................6
1.1 Features .............................................................................................................................6
Chapter 2 — Installation and Configuration ....................................................................7
2.1 Package Contents..............................................................................................................7
2.2 Mounting the Camera ........................................................................................................ 8
2.2.1 Wall Mounting ............................................................................................................9
2.2.2 Ceiling Mounting .....................................................................................................10
2.3 Basic Configuration of Dome Camera System .............................................................. 11
2.4 Setting Dome Camera (DIP Switch) ................................................................................ 12
2.5 Setting Dome Camera Address (ID)................................................................................13
2.6 Connections.....................................................................................................................13
2.7 Getting Started.................................................................................................................14
Programming ...................................................................................................................15
3.1 Dome Camera Selection..................................................................................................15
3.2 Accessing the On-Screen Menu Utility........................................................................... 15
3.3 How to Control the On-Screen Menu Utility...................................................................15
3.4 Auto Scan.........................................................................................................................16
3.5 Preset ............................................................................................................................... 18
3.6 Tour................................................................................................................................... 20
3.7 Pattern ..............................................................................................................................21
3.8 Privacy Zone .................................................................................................................... 22
3.9 Camera Menu ...................................................................................................................23
3.10 Dome Communication...................................................................................................26
3.11 Alarm...............................................................................................................................26
3.12 Dome Setup.................................................................................................................... 27
Operation..........................................................................................................................33
Using a ViconNet VMS ..........................................................................................................33
Using a Valerus VMS..............................................................................................................34
Appendix A — Specifications .........................................................................................35
Appendix B – Programmed Presets...............................................................................37
Appendix C — Troubleshooting .....................................................................................38

6
Chapter 1 — Introduction
1.1 Features
• Built-in optical power zoom camera with True Night Shot function.
• 240 preset positions with the individual camera AE setup.
• 8 tours, consisting of presets, patterns, auto scans and other tours, can be programmed with
over 300 functions and preset locations. While moving, each preset scan can be watched in
smooth Vector Scan mode.
• 16 auto scans in the normal, the vector, and the random mode and the endless autopan with
13 speed steps.
• 8 patterns (up to 500 seconds) and 16 privacy zones.
• 4 alarm inputs, 2 alarm outputs (5VTTL).
• Variable speed from 0.1/sec. to 380/sec.
Three variable speeds (SLOW, NORMAL, TURBO).
• Pan/tilt speed is inversely proportional to the zoom ratio with the option.
• Maximum speed is 380/sec. when preset command.
• Auto calibration from 0.1 to 6 (tilt range is 0 to 180).
• Programmable user preferences (alarm, preset, title, etc.).
• 180 digital flip.
• Function Run menu using keyboard. without function key (preset, pattern, tour and scan).
• Built-in RS-485 receiver driver (up to 3999 selectable camera addresses).
• 12 VDC or 24 VAC for camera.
• 24 VAC for heater and fan.

7
Chapter 2 — Installation and Configuration
2.1 Package Contents
This system comes with the following components;
* Dome Camera 1
* Instruction Manual (this document) 1
* Accessory Kit & Connectors 1
1) Torx wrench (1)
2) 2-Pin Terminal Block (1)
3) 3-Pin Terminal Block (2)
4) 4-Pin Terminal Block (1)
5) 5-Pin Terminal Block (1)
* Install Adaptor 1
NOTE: Check your package to make sure that you received the complete system, including all
components listed above.
NOTE: Adapter for 12 VDC & 24 VAC is not supplied.

8
2.2 Mounting the Camera
An optional mount kit, either a wall mount or a ceiling mount, is required for installation.
The wall or ceiling mount must be attached to a structural object such as hard wood or concrete
that will support the weight of the mount and dome camera.
The use of a solid backboard is recommended when attaching to gypsum walls.
1. Remove the Protection pad and the tape from attached the dome camera.
2. Attach the mounting base to wall using the supplied M8 tapping screw and plastic bushing.
(For Ceiling installation use the supplied M6 tapping screw and bushing.)
3. To seal tightly, wrap the thread of the pipe end with Teflon tape about 20 times for sealing.
Then use a silicone rubber sealant to seal the area where the wall (ceiling) mount and the pipe
meet.
4. Place a bead of silicone sealant around the wall and ceiling mount mounting flange, press it to
the surface and line up the flange hole with drilled holes.
CAUTION 1: A silicone rubber sealant must be applied to seal the housing to secure
waterproofing.
CAUTION 2: When installing, a mounting bracket must be used.
CAUTION 3: Please reset the camera after 30 ~ 60 minutes when installing it in environments
colder than 14° F (-10°C).
CAUTION 4: Regardless of the installation environment, heater and fan power supply is
recommended.

9
2.2.1 Wall Mounting
The wall mounting plate must be attached to a structural object such as concrete that will support
the weight of the mount and dome camera.
1. Select a suitable mounting location and verify there is sufficient cable to reach the middle of
the wall mount.
2. Mark and drill mounting holes in the surface using the wall mount flange as a template.
3. Pull out cables required from the wall to connect to the dome camera.
4. Secure the wall mount bracket to the wall using plastic anchors and 8x35 screws provided or
hardware appropriate for the mounting surface.
5. Remove the access plate and pull cables out through rectangular access hole of the wall
mount bracket.
6. Attach the 1.5-inch adapter to wall mount bracket and secure it using set screw.
7. Attach the camera’s safety wire to the wall mount bracket and neatly gather cables.
8. Reattach the access plate of the wall mount bracket.
9. Push in and turn the camera clockwise into the adapter, and secure it using set screw of the
adapter.

10
2.2.2 Ceiling Mounting
The ceiling mounting plate must be attached to a structural object such as concrete that will
support the weight of the mount and dome camera.
This figure shows how to twist and lock the housing
with pipe.
1. Select a suitable mounting location
and verify there is sufficient cable to
connect with cables from the
housing.
2. Mark and drill mounting holes on the
surface using the ceiling mount
flange as a template.
3. Pull out the cables from the ceiling
required to connect to the dome
camera.
4. Attach the ceiling mount bracket
using plastic anchors and screws
appropriate for the mounting
surface.
5. Attach 1.5-inch adapter to the pipe
and secure it using set screw of the
adapter.
6. Route camera cables through the
pipe and attach the camera to
adapter and secure using set screw
of the adapter.
7. Attach safety wire to the pipe using
6x35 screws.
8. Connect cables and gather cables
neatly.
9. Lock hexagonal nut of the ceiling
mount bracket to secure camera’s
attached pipe and ceiling mount
bracket.

11
2.3 Basic Configuration of Dome Camera System
No.
Type
Description
1
3-PIN
TERMINAL BLOCK
CAMERA POWER
2
3-PIN
TERMINAL BLOCK
HEATER & FAN
(24 VAC)
3
2-PIN
TERMINAL BLOCK
TX+: RS485+ (A)
TX-: RS485- (B)
4
5-PIN
TERMINAL BLOCK
A1: ALARM INPUT 1
A2: ALARM INPUT 2
A3: ALARM INPUT 3
A4: ALARM INPUT 4
GND
5
4-PIN
TERMINAL BLOCK
AO1: ALARM OUTPUT 1
GND
AO2: ALARM OUTPUT 2
GND
6
BNC BLACK
HD OUTPUT
7
BNC YELLOW
CVBS OUTPUT
The dome camera must be installed by qualified service personnel in accordance with all local and
federal electrical and building codes.

12
2.4 Setting Dome Camera (DIP Switch)
NOTE: Open the DIP switch cover and change the setting of DIP switch.
After changing the setting, be sure to close the cover tightly to ensure waterproofing.
S1 S2
You can set video signal with D1 and video type with D2 in S1.
S1-D1
Video Signal
S1-D2
Video Type
OFF
HD-TVI Output
OFF
NTSC
ON
AHD Output
ON
PAL
You can set the PTZ coaxial protocol with D3 and D4 in S1. By default, the unit will auto-detect the
system controlling the unit; the unit is set to Vicon protocol.
S1-D3
S1-D4
HD-TVI Output
AHD Output
OFF
OFF
Hikvision-C
ACP-PTZ
ON
OFF
Pelco-C
Reserved
OFF
ON
Reserved
Reserved
ON
ON
Reserved
Reserved
You can set CVBS output with D1 in S2.
S2-D1
WDR Type
WDR Control
CVBS Output
HD Output
OFF
True WDR
OFF
Enabled
Enabled
ON
Disabled
Enabled
ON
Digital WDR
OFF
Enabled
Enabled
ON
Enabled
Enabled

13
2.5 Setting Dome Camera Address (ID)
To prevent damage, each dome camera must have a unique address (ID).
The factory default setting is 1. When using ViconNet, the dome ID is set in the VMS.
Refer to 3.10 Dome Communication section for detailed information.
2.6 Connections
• Connecting to the RS-485
The dome camera can be controlled remotely by an external device or control system, such as a
control keyboard, using RS-485 half-duplex serial communications signals. It is important to
remember that you cannot mix protocols.
• Connecting HD Output connector
Connect the HD output (BNC) connector to the video input; use an encoder as needed for
the VMS system.
• Connecting CVBS Output connector
Connect the CVBS output (BNC) connector to the video input.
• Connecting Alarms
- A1, A2, A3, A4 (Alarm Input 1, 2, 3, 4)
You can use external devices to signal the dome camera to react on events. Mechanical or
electrical switches can be wired to the A1, A2, A3, A4 (Alarm Input 1, 2, 3, 4) and G (Ground)
connectors.
See Chapter 3 — Program and Operation for configuring alarm input.
- G (Ground)
NOTE: All the connectors marked G or GND are common.
Connect the ground side of the alarm input and/or alarm output to the G (Ground) connector.
- AO1, AO2 (5VTTL Alarm Output 1, 2)
The dome camera can activate external devices such as buzzers or lights. Connect the device
to the AO1, AO2 (Alarm Output 1, 2) and G (Ground) connectors.
See Chapter 3 — Program and Operation for configuring alarm output.
• Connecting the Power of Camera
Connect power of 12 VDC or 24 VAC for the dome camera.
When using a 12 VDC adapter, connect the positive (+) pole to the ‘+’ position and
the negative (-) pole to the ‘-’ position.
Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class 2 power source only.
• Connecting the Power of Heater & Fan
Connect power of 24 VAC for the heater and fan.
Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class 2 power source only.

14
2.7 Getting Started
Note: This manual pertains to working with Vicon protocol on a ViconNet/Valerus VMS or Vicon
keypad.
After dome camera is installed, installed apply power to the dome camera. The dome camera will
start a configuration sequence.
Below is a typical layout of the OSD screen after the OSD has been configured and enabled.
OSD Position
001 AF AE
EMPTY DATA
ALARM:1
DOMEID:0001
360.0 090.0
ViconNet screen
Valerus Configuration screen
ZOOM +/-
CONTROLS
INFORMATION
DISPLAY
CAMERA TITLE & ID
PAN & TILT ANGLE
FUNCTION TITLE
STATUS of
FOCUS and AE
ALARM DISPLAY
PTZ/PRESET
CONTROLS
PTZ/PRESET
CONTROLS
UP/DOWN AND
LEFT/RIGHT
CONTROLS
ZOOM +/-
CONTROLS
UP/DOWN AND
LEFT/RIGHT
CONTROLS:
Use Mouse Cursor

15
Chapter 3 — Program and Operation
Programming
The programming instructions below are based on Vicon protocol. The dome can be controlled by
a Vicon keypad or by a Vicon VMS system, ViconNet or Valerus. When using the camera with
ViconNet, the camera ID is assigned within the ViconNet programming system. Only a user with
administrator privileges can perform these functions.
3.1 Dome Camera Selection
Select the camera from the VMS list or, if a keyboard is being used to program and operate the
dome camera, select the dome camera by pressing CAM + No. + CAM keys. The selected dome
camera will be displayed on the monitor.
3.2 Accessing the On-Screen Menu Utility
You can call up the On-screen menu utility on your monitor by selecting Preset 94 from
ViconNet/Valerus or enter Preset 94 from the keyboard (in Valerus you must be in the
Configuration/Resources/Video Channel); the following On-screen main menu will appear:
DOME MENU
AUTO SCAN
PRESET
TOUR
PATTERN
PRIVACY ZONE
CAMERA
DOME COMMUNICATION
ALARM
DOME SETUP
EXIT(ESC TO EXIT)
3.3 How to Control the On-Screen Menu Utility
The menu system can be navigated using controls on the VMS screen or on the keypad. The
cursor can be moved up/down or right/left using the arrow keys on the ViconNet screen, the cursor
on the Valerus screen or moving the joystick in that direction. The zoom +/- on ViconNet/Valerus or
twisting the joystick are used to change values within the menu selection. Various preset functions
are also predefined to perform certain functions. Note that an ! displays at the currently selected
function.
Function
Button
Call the On-screen menu utility.
Preset 94
Navigate through the menu items.
Up/Down
Go into the sub-menu items.
Right/Left
Change value.
Right/Left; Zoom +/-
Control Key Mode (required in some
menus)
Preset 95
ESC key
Preset 96

16
3.4 Auto Scan
The Auto Scan supports up to 17 programmed sector angles at user-programmable speeds. Only 8
of these can be called up; the remaining can be set and used as steps in a tour if needed. Use
UP/DOWN to navigate through the menu selections; use either the UP/DOWN or +/- to change the
value of the selection.
AUTO SCAN SETUP
NUMBER : 01
TITLE : A01
MODE : NORMAL
SPEED : 5 STEP
START ANGLE : ----- ----- --
END ANGLE : ----- ----- --
SCAN DIR : CCW
SWAP : OFF
DWELL : 03 SEC
FOCUS : AUTO
SAVE AND EXIT(ESC TO CANCEL)
NUMBER 01 ~ 08, 10 ~ 17, 09: AUTO-PAN mode (endless panning).
TITLE Up to 6 characters.
MODE NORMAL, VECTOR, RANDOM (AUTO-PAN mode: NORMAL, RANDOM only).
NORMAL Move from start point to end point in panning only.
VECTOR Move from start point to end point including tilt and zoom simultaneously and
linearly.
RANDOM Move randomly between the start point and the end point.
SPEED 1 ~ 13 step, the lower number means the slower speed.
SCAN DIR Set the Scan direction, CCW (Counterclockwise), CW (Clockwise).
SWAP Swap the start point for the end point.
DWELL Set the dwell time at the both end, 01 ~ 99 seconds.
FOCUS AUTO, MANUAL
Follow these steps to program Auto Scan:
1. Enter PRESET 94 to display the main menu on the monitor. Use UP/DOWN to select Auto Scan
and RIGHT/LEFT to open the Auto Scan menu.
2. Select “NUMBER” and set the desired number by pressing the RIGHT/LEFT or +/-.
3. Select “TITLE” and press the RIGHT/LEFT or +/- to enter the title edit mode.
4. There is a 3-character default title. Use the +/- to change the alphanumeric characters and
RIGHT/LEFT to navigate to the next position in the title. As an alternative, move down to the
character table using UP/DOWN. This menu requires the CTRL key, which is preset 95, to set
the title. Use RIGHT/LEFT to navigate to the desired character and select preset 95 to set; the
cursor position moves to the next position automatically. Use RIGHT/LEFT at the “ALL DELETE”
field to delete all characters. Use RIGHT/LEFT at the “EXIT” field to save and exit title edit menu.
Use the ESC preset 96 to exit without saving.

17
TITLE EDIT MENU
(CTRL KEY)
A01
$
A B C D E F G H I J
K L M N O P Q R S T
U V W X Y Z 0 1 2 3
4 5 6 7 8 9 ( )
ALL DELETE
EXIT(ESC TO EXIT)
5. Select “MODE” and “SPEED”.
6. Select “START ANGLE”. This menu requires the CTRL key, which is preset 95. Use the
RIGHT/LEFT to move to the field you want to change; use +/- to change the value. The unit will
move to that position. Use the RIGHT/LEFT to move to the next field and change that value with
+/-. When the position is set, select Preset 95 to set it.
7. Select “END ANGLE”. This menu requires the CTRL key, which is preset 95. Use the
RIGHT/LEFT to move to the field you want to change; use +/- to change the value. The unit will
move to that position. Use the RIGHT/LEFT to move to the next field and change that value with
+/-. When the position is set, select Preset 95 to set it.
8. Set “SCAN DIR” to CCW or CW using RIGHT/LEFT.
9. Select “SWAP”; set to ON, using RIGHT/LEFT, to exchange the start angle and the end angle.
10. Set “DWELL time”. Use RIGHT/LEFT to change value.
11. Set “FOCUS” using RIGHT/LEFT to change selection.
12. Select “SAVE AND EXIT” and use RIGHT/LEFT to save and exit menu. Use the ESC, preset
96, to exit without saving.

18
3.5 Preset
If you need to view specific places routinely, you should program Presets. A Preset is a
programmed video scene with automatic pan, tilt, zoom, focus, and AE settings. In addition,
Presets may be assigned the “Home” position for the dome camera. Up to 59 presets (1-59),
whose positions are saved in the dome camera’s firmware, may be programmed and called up.
The other preset numbers have pre-programmed functions. See those presets listed at the end of
this document.
There are eight pages of Preset menu. Each page has 30 Presets. Pages can be scrolled using
the RIGHT/LEFT on the first or last No. of Preset.
PRESET SETUP
NUMBER : 001
TITLE : ------
CAMERA SET
DWELL : -- SEC
1 2 3 4 5 6 7 8 9 0
- $ - - - - - - - -
- - - - - - - - - -
- - - - - - - - - -
NEXT PAGE
SAVE AND EXIT(ESC TO CANCEL)
Key to symbols:
-Blank Preset position.
$Position has the Preset.
!Current cursor position.
Before presets can be configured, they have to be set in Run/Operation mode. Exit programming
mode and store the preset positions. Return to Programming mode.
Follow steps below to store the Preset positions:
1. Enter PRESET 94 to display the main menu on the monitor. Use UP/DOWN to select Preset
and RIGHT/LEFT to open the Preset Setup menu.
2. Select the Preset position to be configured using RIGHT/LEFT.
3. Select “TITLE” to edit the preset title. Follow the procedure of the Auto Scan above to edit titles.
5. Select “CAMERA SET” and use RIGHT/LEFT to display the Preset Camera Setup menu.
PRESET CAMERA SETUP
FOCUS : AUTO
MOTION : OFF
MOTION SETUP
AE SETUP
SAVE AND EXIT(ESC TO CANCEL)
Set FOCUS AUTO, MANUAL, ONE PUSH.
Set MOTION OFF, ON.
Use RIGHT/LEFT or +/- to select the settings for Focus and Motion.

19
Select “MOTION SETUP” and use RIGHT/LEFT to display the MOTION Setup menu.
MOTION SETUP
SENSITIVITY : 10
POSITION : ALL
DELAY : 00 SEC
OUTPUT : OFF
HOLD TIME : 03 SEC
EXIT(ESC TO EXIT)
Set SENSITIVITY 00 ~ 20.
Set POSITION ALL, CENTER.
Set DELAY 00 ~ 05 seconds.
Set OUTPUT OFF, OUT1, OUT2.
Set HOLD TIME 03 ~ 99 seconds.
Use RIGHT/LEFT or +/- to select the settings for Motion.
Select “AE SETUP” and use RIGHT/LEFT to display the AE setup menu. Then the AE setup
displays. Refer to the AE SETUP in the camera setup.
6. Set “DWELL time”. (03 ~ 99 seconds) using the RIGHT/LEFT or +/- to select the value.
7. To select the next page of Presets, scroll the page by pressing the RIGHT/LEFT on the first or
last columns of the menu.
8. Repeat step 2 through 7 for each additional Preset position.
9. Select “SAVE AND EXIT” and use RIGHT/LEFT to save these settings and exit. Use the ESC,
preset 96, to exit without saving.

20
3.6 Tour
There are 8 programmable Tours. Each Tour consists of up to 40 preset positions, patterns, scans
or other tours (second-level). Using second-level tours, it can be expanded to over 300 functions in
a single tour.
TOUR SETUP
NUMBER : 01
TITLE : T01
SCAN TYPE : NORMAL
SPEED : -- STEP
TOUR FUNCTION
SAVE AND EXIT(ESC TO CANCEL)
TOUR FUNCTION SETUP
(CTRL KEY)
DWELL : -- SEC
003 A04 --- --- ---
--- --- --- --- ---
--- --- P01 --- ---
--- T02 --- --- ---
--- --- --- --- ---
--- --- --- --- ---
--- --- --- --- ---
--- --- --- --- ---
EXIT(ESC TO EXIT)
--- Blank position.
SCAN TYPE NORMAL, VECTOR.
SPEED 01 ~ 13; available for VECTOR only.
DWELL 03 ~ 99 seconds.
003 Preset (1 ~ 59).
A04 Auto Scan (1 ~ 8, 10 ~ 17).
P01 Pattern (1 ~ 8).
T02 Tour (1 ~ 8).
Note that presets, auto scans and patterns must be set up before they can be used in a tour.
Follow the steps below to program the Tours:
1. Enter PRESET 94 to display the main menu on the monitor. Use UP/DOWN to select Tour and
RIGHT/LEFT to open the Tour Setup menu.
2. Select “NUMBER” and set the desired number by using the RIGHT/LEFT.
3. To edit the “TITLE” follow the procedure of the Auto Scan (above) to edit titles.
4. Select “SCAN TYPE” and use RIGHT/LEFT to select NORMAL or VECTOR.
5. Select “SPEED” and use RIGHT/LEFT to select the number of steps, up to 13. SPEED is only
available in VECTOR mode.
6. Select “TOUR FUNCTION” and use RIGHT/LEFT to display the TOUR FUNCTION SETUP
menu. This menu requires using the CTRL key, preset 95.
7. Select “DWELL” to enter the time the dome will stay in that position before moving to the next
position.
8. Use the +/- to enter the preset, auto scan, pattern or tour in that position; use the RIGHT/LEFT
to move to the next position.