Vicon Roughneck V920D Series User manual

www.vicon-security.com
XX258-00-07
Roughneck V920D Series
Network Camera Domes
Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet your requirements or that the
operation will be entirely error free or perform precisely as described in the documentation. This system has not been designed
to be used in life-critical situations and must not be used for this purpose.
Vicon Industries Inc.
Tel: [phone] Fax: [phone] Toll Free: 800-645-9116
24-Hour Technical Support: 800-34-VICON (800-348-4266) UK: 44/(0) 1489-566300
Document Number: 8009-8258-00-07
Product specications subject to change without notice.
Issued: 314
Copyright © 2014 Vicon Industries Inc. All rights reserved.
Installation Guide

WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT INSERTANY METALLIC
OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENINGS ON THE EQUIPMENT.
CAUTION
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user
to the presence of uninsulated "dangerous voltage" within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature accompanying the
appliance.
PRECAUTIONS
Safety -------------------------------------- Installation -------------------------------
Should any liquid or solid object fall into the cabinet,
unplug the unit and have it checked by the qualified
personnel before operating it any further.
Unplug the unit from the wall outlet if it is not going to
be used for several days or more. To disconnect the
cord, pull it out by the plug. Never pull the cord itself.
Allow adequate air circulation to prevent internal heat
build-up. Do not place the unit on surfaces (rugs,
blankets, etc.) or near materials (curtains, draperies)
that may block the ventilation holes.
Height and vertical linearity controls located at the rear
panel are for special adjustments by qualified
personnel only.
Before installation, carefully read the manual to ensure
correct operation and setup, heeding all warnings and
instructions.
Do not install the device near any heat sources such as
radiators, heat registers, stoves, or other equipment
(including amplifiers) that produce heat.
Only use attachments/accessories
specified by the
manufacturer.
Do not install the device in a place where it is exposed
to gas or oil.
Cleaning ---------------------------------
Clean the unit with a slightly damp soft cloth.
Use a mild household detergent. Never use strong
solvents such as thinner or benzene as they might
damage the finish of the unit.
Retain the original carton and packing materials for
safe transport of this unit in the future.
2

FCC COMPLIANCE STATEMENT
INFORMATION TO THE USER:THIS EQUIPMENT HAS BEEN TESTED AND
FOUND TO
COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC
RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL
INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT. THIS
EQU
IPMENT GENERATES, USES, AND CAN RADIATE RADIO FREQUENCY ENERGY AND IF NOT
INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL
INTERFERENCE TO RADIO COMMUNICATIONS.
CAUTION:CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY T
HE PARTY
RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER'S AUTHORITY TO OPERATE THE
EQUIPMENT.
THIS CLASS A DIGITALAPPARATUS COMPLIES WITH CANADIAN ICES-003.
CET APPAREIL NUMÉRIQUE DE LA CLASSE A EST CONFORME À LA NORME NMB-003 DU CANADA.
CE COMPLIANCE STATEMENT
WARNING: This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
3

IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has
two blades with one wider than the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong is provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified
by the manufacturer, or sold with the apparatus. When a cart is
used, use caution when moving the cart/apparatus combination
to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused
for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
15. CAUTION – THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALIFIED
SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF ELECTRIC SHOCK DO
NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE
OPERATING INSTRUCTIONS UNLESS YOU ARE QUALIFIED TO DO SO.
16. Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class 2
power source only.
17. ITE is to be connected only to PoE networks without routing to the outside plant.
4

Contents
1. Description ------------------------------------------------------------------6
1.1 Components-- ------------------------------------------------------------------------------------------- 6
1.2 Key Features - ------------------------------------------------------------------------------------------- 7
2. Installation ------------------------------------------------------------------- 8
2.1 Overview----------------------------------------------------------------------------------------------------8
2.2 Connection------------------------------------------------------------------------------------------------16
2.3 Network Connection and IP Assignment ----------------------------------------------------------- 18
3. Operation -------------------------------------------------------------------- 20
3.1 Access from a browser --------------------------------------------------------------------------------- 20
3.2 Access from the internet------------------------------------------------------------------------------- 21
3.3 Setting the admin password over a secure connection ------------------------------------------- 21
3.4 Live View Page------------------------------------------------------------------------------------------- 21
3.5 Network Camera Setup--------------------------------------------------------------------------------- 24
3.5.1 Basic Configuration------------------------------------------------------------------------------ 24
1) Users------------------------------------------------------------------------------------------- 25
2) Network --------------------------------------------------------------------------------------- 26
3) Video & Image ------------------------------------------------------------------------------- 27
4) Audio-------------------------------------------------------------------------------------------29
5) Date & Time ---------------------------------------------------------------------------------- 31
3.5.2 Live View, Source-------------------------------------------------------------------------------- 32
3.5.3 Video & Image----------------------------------------------------------------------------------- 33
3.5.4 Audio-----------------------------------------------------------------------------------------------39
3.5.5 Event ----------------------------------------------------------------------------------------------- 40
1) Event-In --------------------------------------------------------------------------------------- 41
2) Event-Out ------------------------------------------------------------------------------------- 46
3) Event Map------------------------------------------------------------------------------------- 53
3.5.6 System ------------------------------------------------------------------------------------------- 55
1) Information ----------------------------------------------------------------------------------- 55
2) Security---------------------------------------------------------------------------------------- 56
3) Date & Time ---------------------------------------------------------------------------------- 59
4) Network --------------------------------------------------------------------------------------- 60
5) Language-------------------------------------------------------------------------------------- 70
6) Maintenance ---------------------------------------------------------------------------------- 71
7) Support ---------------------------------------------------------------------------------------- 72
3.6 Playback -------------------------------------------------------------------------------------------------- 73
3.7 Help---- --------------------------------------------------------------------------------------------------- 75
3.8 Resetting to the factory default settings-------------------------------------------------------------- 76
4. Appendix -------------------------------------------------------------------- 77
4.1 Troubleshooting------------------------------------------------------------------------------------------- 77
4.2 Alarm Connection----------------------------------------------------------------------------------------- 78
4.3 Preventive Maintenance --------------------------------------------------------------------------------- 79
4.4 Product Specification------------------------------------------------------------------------------------- 79
5

1. Description
The information in this manual provides quick installation and setup procedures for the Roughneck®
V920D Series of Camera Domes. These units should only be installed by a qualified technician using
approved materials in conformance with federal, state, and local codes. Read these instructions
thoroughly before beginning an installation. Always refer to Vicon’s website to assure you have the
most up-to-date manual, www.vicon-security.com.
The V920D Series of HD IP Camera Domes is designed for demanding security installations. It offers a
number of fixed network camera versions that deliver crisp clear images to fit any installation need;
models with IR illuminators are available. The V920D cameras are fully compatible with all ViconNet®
systems; its ONVIF certification provides an open-platform for integration into other video
management systems.
The housing is designed for easy installation. PoE eliminates the need for power cables, providing a
cost-effective method of installation. The V920D features an autoiris lens that adapts to changing
outdoor lighting; the true day/night camera includes a removable IR cut filter. The camera dome is
IP66 rated with a vandal-proof casing that withstands rain, dust and vandalism. It provides 3-axis
adjustment. The alarm input and alarm output can be used to connect various third party devices,
such as door sensors and alarm bells.
1.1 Components
The system comes with the following components:
Camera unit Installation CD Installation Guide Template Sheet Accessory Kit
Optional OSD Controller
Check your package to make sure that you received the complete system, including all components
shown above.
Note: The optional V920D-OSD OSD Controller and V920D-AUDIO audio cable assembly can be
purchased separately.
6

1.2 Key Features
• Brilliant video quality
The network camera offers the highly efficient H.264 video compression, which drastically
reduces bandwidth and storage requirements without compromising image quality. Motion JPEG
is also supported for increased flexibility.
• Dual or triple streams
The network camera can deliver dual or triple video streams simultaneously at full frame rate in
all resolutions up to Full-HD (1920 x 1080p) using Motion JPEG and H.264 (or MPEG-4). This
means that several video streams can be configured with different compression formats,
resolutions and frame rates for different needs.
• Image setting adjustment
The network camera also enables users to adjust image settings such as contrast, brightness and
saturation to improve images before encoding takes place.
• Intelligent video capabilities
The network camera includes intelligent capabilities such as enhanced video motion detection.
The network camera’s external inputs and outputs can be connected to devices such as sensors
and relays, enabling the system to react to alarms and activate lights or open/close doors.
• Easy Focus (motorized versions only)
Easy Focus will be activated once Day/Night mode is switched and the focus readjusts
automatically.
• Focus & Zoom Control via Network
The network camera also enables users to adjust focus and zoom remotely via the network.
• Resolution
V922D series (2 Megapixel): 1920x1080 @ 30 fps;
V921D series (1 Megapixel): 1280x720 @ 30 fps;
V920D series (standard resolution, 0.3 Megapixel): 704x480 @ 30 fps.
• Micro-SD Recording support
The network camera also supports a micro-SD memory slot for local recording with removable
storage.
• Improved Security
The network camera logs all user access and lists currently connected users. Also, its full frame
rate video can be provided over HTTPS.
• Power over Ethernet
Support for Power over Ethernet (IEEE802.3af) enables the unit, as well as the camera module
that is connected to it, to receive power through the same cable as for data transmission. This
makes for easy installation since no power outlet is needed.
• ONVIF
This is a global interface standard that makes it easier for end users, integrators, consultants,
and manufacturers to take advantage of the possibilities offered by network video technology.
ONVIF enables interoperability between different vendor products, increased flexibility, reduced
cost, and future-proof systems.
7

2. Installation
For the network camera to operate, it is necessary to connect a network cable for data transmission
and power connection from customer-supplied power adapter. Depending on operation methods, it is
possible to also connect an alarm cable.
2.1 Overview
Parts and Description (Models equipped without IR LEDs)
8

Parts and Description (Models equipped with IR LEDs)
9

Unpacking and Inspection
All Vicon equipment is tested and inspected before leaving the factory. It is the carrier responsibility to
deliver the equipment in the same condition as it left the factory.
Inspection for Visible Damage
Immediately inspect the cartons upon delivery. Make a note of any visible damage on all copies of the
carrier’s freight bill.
Make sure the carrier’s agent (the person making the delivery) signs the note on all copies of the bill.
If the agent does not have claim forms, contract the carrier’s office.
Inspection for Concealed Damage
As soon as possible after delivery, unpack the unit and inspect it for concealed damage. Do not
discard the carton or packing materials. If the unit is damaged, contact the carrier immediately and
request forms for filing a damage claim. Make arrangements for a representative of the carrier to
inspect the damaged equipment.
If the equipment must be returned for repair, follow the Shipping Instructions at the end of this
manual.
Roughneck V920D-IP Dome Components
The Roughneck V920D-IP units consist of a base (which includes the camera mounting bracket with
the camera/lens assembly) and a cover with a smoked dome. Refer to Figure 1.
Base/Camera Mounting Bracket
The base of the unit is constructed of die-cast aluminum. The base is mounted directly to the wall or
ceiling. Two cable access holes are provided. A safety cord is provided to connect the cover to the
base. The camera mounting bracket is attached to the base; the camera is factory-installed. The
camera/lens position can be manually adjusted. A heater is factory-installed for units installed in
environments that require it.
Cover/Dome
The cover of the unit is constructed of die-cast aluminum. It has a 4.3 in. (110 mm) diameter dome
constructed of clear polycarbonate plastic. A mask with a slotted opening is included to help conceal
the camera. The cover is secured to the base with four tamperproof captive screws; a special tool is
supplied to loosen the screws. A safety cord is provided to anchor the cover/dome to the base. Refer
to the Maintenance section of this manual for instructions on the care and handling of the dome.
Contents of Package
The content of the package includes the camera in housing, this manual, drilling guide label and
accessory kit for installation.
The contents of the package include:
•Camera in housing
•Instruction manual
•Accessory kit
•Drilling guide label
10

Torx screws
M5x10 (4x)
Accessory Kit
There is an accessory kit included with the Roughneck V920D-IP. The table below lists the contents.
Description Quantity
Torx wrench (to remove tamperproof screws) 1
Pipe sealant tape (to seal pipe fitting to housing)
1
Screws, anchors and rubber washers (for some
appropriate installations)
4 of each
Vent plug (for outdoor installations) 1
Terminal blocks, 3-pin (24 VAC power); 4-pin (alarm
output); 2-pin (RS-485; UTP option)
1, 1, 2
Cable access plug (black; for rear hole)
1
Cable access plug and tool (threaded; for side hole)
1 of each
Grommet (for routing cable; rear access)
1
Mounting the Unit
Select a location for the installation of the V920D-IP camera. Be sure the area around the selected
location is clear of obstacles (such as steel beams, headers, pipes, electrical wiring, etc.) which would
interfere with the mounting of the camera and that the location can support the weight of the unit
[the V920D-IP unit weighs 2.5 lb (1.1 kg)]. Video and power cables must be routed to the installation
location.
The V920D-IP mounts directly to a ceiling or wall. The base has four mounting holes; two cable
access holes are provided. As a mounting alternative, the mounting holes align with a standard 4 x 4
electrical box for mounting; an adapter plate is available that creates an aesthetically pleasing
appearance (model V910/V600W-PLATE). Refer to Mounting Hole Figure that follows. To mount the
V920D-IP, follow the steps below.
Caution: Do not attach these units to drywall surfaces and do not install mounting screws into the
end grain of wood.
1. Loosen the four (4) Torx screws securing the cover; leave the screws intact. The cover is
attached to the base by the safety cord upon delivery. Allow the cover to hang.
11

2. Using the drilling guide as a template, mark the location of the four mounting holes [0.203 in.
(5.2 mm) diameter]. See Figure that follows.
Mounting Hole Pattern
3. There are two (2) cable access holes provided. Drill a hole in the wall or ceiling and route video
and power cables to the selected location and through one of the cable access holes. A 1/2-inch
connection (customer-supplied connector) is provided on the side of the base. A conduit or
electrical connector (screw-type) can be used in this threaded hole. The rear port is sized to
accept a 1/2-in. (customer-provided) connector. If it is desirable to use the rear cable access hole,
route the conduit through the hole; the supplied grommet can be used instead of the conduit.
Apply the provided sealant tape around the threads of the conduit pipe. See Figure above for hole
locations.
4. If using the rear cable access hole, insert the vent plug provided in the side cable access hole. If
the side cable access hole is used, insert a Street Tee (customer provided) into the cable access
hole. Route the conduit through the top hole and insert the vent plug provided into the bottom
hole. Refer to Figure that follows for installation options. Sealant tape is provided for the plug and
Street Tee. Insert the black plug provided into the rear cable access hole if the side access hole is
being used; if the rear cable access hole is being used, insert the provided plug into the side cable
access hole and tighten with tool provided.
Note: Failure to thoroughly coat threads will result in moisture entering the housing and eventual
failure of the unit.
Note: For outdoor installations, Vicon recommends that the vent plug should only be used if
fogging conditions exist. Additionally, if the side cable access hole is used, the base must be
mounted so the hole is pointed directly downward.
12

Installation Options
5. Fasten the base to the wall or ceiling with the appropriate hardware for the mounting surface, lag
bolts and sleeve for cement surfaces or machine screws for other surfaces.M6x35 tapping screws
are supplied for use, if suitable. A rubber washer is provided for each mounting hole for
environmental sealing. If the rear cable access is used, be sure that holes are aligned correctly so
the cable is routed to allow a flush installation of the base. As a mounting alternative, align the
mounting holes with a 4 x 4 electrical box and fasten the base to the box with machine screws.
13

Seal around the
housing base
tightly using the
silicone.
Note: To assure a watertight seal, apply silicone sealant around the area where the base meets the
wall or ceiling. Vicon recommends Dow Corning® 737 neutral cure sealant or equivalent.
6. The camera/lens assembly can be adjusted to the desired position. Do not move the
camera/lens assembly by holding onto the lens. For pan and tilt adjustment, move the
camera mechanism in the desired direction. For roll adjustment (turns camera position
top/bottom), turn the gimbal in the desired direction. The varifocal lens can be manually adjusted
for focus (near/far) and zoom (telephoto/wide). Set the zoom position by using Zoom Lever Screw;
set the focus by using Focus Lever Screw. Refer to Lens Adjustment. When making adjustments,
be sure that the lens does not hit the dome and that the camera/lens is positioned for proper
orientation of video display.
Adjusting the 3-Axis Gimbal
The gimbal mechanism yields maximum rotation and placement as shown below.
• Z-Axis: Rotation 355°
• Y-Axis: Tilting 70°
• X-Axis: Panning 355°
Models without IR LEDs Models equipped with IR LEDs
14

Camera Dimensions
See the diagrams below for the exact dimension of the network camera dome.
Dimensions Unit: mm
15

2.2 Connections
Connection Description
No.
Connector Name
Description
1
Micro-SD Slot
Micro-SD memory slot
2
Service Monitor
Port
Service Monitor (set to NTSC by default ; change video format from
Source menu) & OSD Controller Communication Port, Mono Jack
3
Audio In & Out
Port Audio Input and Output, Mono Jack.
V920D-AUDIO cable assembly is available as an option.
4
Alarm In & Out
Port
Alarm Input and Output, 3 pin terminal
Pin 1: Alarm In
Pin 2: GND
Pin 3: Alarm Out
5 Main Power
Main Power, 2 pin terminal,
12 VDC: 470 mA (5.4 W), 24 VAC: 520 mA (6.5 W) IR on, without
heater, or
12 VDC: 900 mA (10 W), 24 VAC: 900 mA (11.8 W) with IR and
heater
Pin 1: 12 VDC/24 VAC, Pin2: GND/24 VAC
6 RJ-45 Port
Ethernet, RJ-45 port compatible with 10/100 Mbps having PoE
functionality
Micro SD memory slot on the Board
Card Slot for Micro SD memory: Socket “J15”
• Connecting to the RJ-45
Connect a standard RJ-45 cable to the network port of the network camera. Generally a
crossover cable is used for direct connection to a PC, while a direct cable is used for connection
to a hub.
A router featuring PoE (Power over Ethernet) can also be used to supply power to the camera.
• Connecting Alarms
AI (Alarm In):
External devices can be used to signal the network camera to react upon events. Mechanical or
electrical switches can be wired to the AI (Alarm In) and G (Ground) connectors.
G (Ground):
Set to NTSC
by default
16

Connect the ground side of the alarm input and/or alarm output to the G (Ground) connector.
Alarm Out:
The network camera can activate external devices such as buzzers or lights. Connect the device
to the AO (Alarm Out) and G (Ground) connectors.
Connecting Audio
Use the optional V920D-AUDIO cable assembly for ease of audio connections. The cables are labeled for
Audio In and Audio Out. Refer to diagram below.
Audio Out: Connect wire 1 and ground to speakers.
Audio In: Connect wire 2 and ground to microphone.
• Connecting the Power
Connect the power of 12 VDC or 24 VAC for the network camera. Connect the positive (+) pole to
the ‘+’ position and the negative (-) pole to the ‘-’ position for the DC power.
Be careful not to reverse the polarity when connecting the power cable.
A router featuring PoE (Power over Ethernet) can also be used to supply power to the
camera.
The heater can be powered by a 24VAC, 12VDC, PoE power source.
For the power specifications, refer to the Appendix, Product Specification.
If PoE and 12 VDC are both applied, the camera will be supplied with power from PoE.
Heater
The heater comes preinstalled in the camera dome.
Power Supply
12 VDC
Power Consumption
3.5 Watt
Heater On
at 59°F (15°C)
Heater Off
at 77°F (25°C)
• Connecting Service Monitor Port
The Service Monitor output port (J7) is located on the board of the dome camera and is used for
easy OSD setup.
17

▶ID & IP assignment
To make changes in the OSD menu, the optional OSD controller (V920-OSD) can be used to set
Camera Title and IP Address.
1. Connect the OSD Controller to the Service Monitor port of the network camera.
2. Connect Service Monitor and the Video Output port of the OSD Controller.
3. Press the SET button on the controller to access the Main Menu.
4. Change camera ID and IP address as needed. Additionally, the Name (or title) of the camera
can be changed. Use the ↑↓←→ buttons on the controller to change the parameters.
5. Select SAVE or CANCEL to exit the Main Menu.
The Video Output can also be used for easy zoom and focus control when adjusting the lens.
Video Output is restricted to 704x480 (576) resolution.
▶Zoom & Focus Control (Models with motorized lens only)
The camera enters Zoom and Focus control mode when the OSD Controller is connected to the
Service Monitor port.
-. Zoom Control: ↑(Zoom In), ↓(Zoom Out)
-. Focus Control: ← (Focus Near), → (Focus Far)
-. Fine Focus: Press and hold the SET button for at least 2 seconds. The camera readjusts
focus automatically.
Note: The optional V920D-OSD OSD Controller can be purchased separately.
2.3 Network Connection and IP assignment
The network camera is designed for use on an Ethernet network and requires an IP address for
access. Most networks today have a DHCP server that automatically assigns IP addresses to
connected devices. By the factory default, your camera is set to obtain the IP address automatically
via DHCP server. If your network does not have a DHCP server the network camera will use
192.168.1.100 as the default IP address.
If DHCP is enabled and the product cannot be accessed, run the “Smart Manager” utility on the CD to
search and allocate an IP address to your products, or reset the product to the factory default settings
and then perform the installation again.
1. Connect the network camera to the network and power up.
18

2. Start SmartManager utility (Start>All Programs>SmartManager>SmartManager); the main
window displays. After a short while any network devices connected to the network will be
displayed in the list.
3. Select the camera on the list and click right button of the mouse. The pop-up menu below
displays.
4. Select Assign IP. The Assign IP window displays. Enter the required IP address.
Note: For more information, refer to the Smart
Manger User’s Manual.
19

3. Operation
The network camera can be used with Windows® operating system and browsers. The recommended
browsers are Internet Explorer®, Safari®, Firefox®, Opera® and Google® Chrome® with Windows.
Note: To view streaming video in Microsoft® Internet Explorer, set your browser to allow ActiveX
controls.
Note: Some screens may appear different (i.e., color scheme) depending on the firmware version, but
the functionality is the same or similar.
3.1 Access from a browser
1. Start a browser (i.e., Internet Explorer).
2. Enter the IP address or host name of the network camera in the Location/Address field of the
browser.
3. A starting page displays. Click Live View, Playback or Setup to select corresponding web page.
4. Click Live View for the network camera’s Live View page to appear in the browser.
20