Vicon V920B Series User manual

www.vicon-security.com
XX271-00-00
V920B Series
Network Bullet Cameras
Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet your requirements or that the
operation will be entirely error free or perform precisely as described in the documentation. This system has not been designed
to be used in life-critical situations and must not be used for this purpose.
Vicon Industries Inc.
Tel: [phone] Fax: [phone] Toll Free: 800-645-9116
24-Hour Technical Support: 800-34-VICON (800-348-4266) UK: 44/(0) 1489-566300
Document Number: 8009-8271-00-00
Product specications subject to change without notice.
Issued: 1114
Copyright © 2014 Vicon Industries Inc. All rights reserved.
Installation Guide

2
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT INSERTANY METALLIC
OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENINGS ON THE EQUIPMENT.
CAUTION
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user
to the presence of uninsulated "dangerous voltage" within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature accompanying the
appliance.
PRECAUTIONS
Safety -------------------------------------- Installation -------------------------------
Should any liquid or solid object fall into the cabinet,
unplug the unit and have it checked by the qualified
personnel before operating it any further.
Unplug the unit from the wall outlet if it is not going to
be used for several days or more. To disconnect the
cord, pull it out by the plug. Never pull the cord itself.
Allow adequate air circulation to prevent internal heat
build-up. Do not place the unit on surfaces (rugs,
blankets, etc.) or near materials (curtains, draperies)
that may block the ventilation holes.
Height and vertical linearity controls located at the rear
panel are for special adjustments by qualified
personnel only.
Before installation, carefully read the manual to ensure
correct operation and setup, heeding all warnings and
instructions.
Do not install the device near any heat sources such as
radiators, heat registers, stoves, or other equipment
(including amplifiers) that produce heat.
Only use attachments/accessories specified by the
manufacturer.
Do not install the device in a place where it is exposed
to gas or oil.
Cleaning ---------------------------------
Clean the unit with a slightly damp soft cloth.
Use a mild household detergent. Never use strong
solvents such as thinner or benzene as they might
damage the finish of the unit.
Retain the original carton and packing materials for
safe transport of this unit in the future.

3
FCC COMPLIANCE STATEMENT
INFORMATION TO THE USER:THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO
COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC
RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL
INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT. THIS
EQUIPMENT GENERATES, USES, AND CAN RADIATE RADIO FREQUENCY ENERGY AND IF NOT
INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL
INTERFERENCE TO RADIO COMMUNICATIONS.
CAUTION:CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY
RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER'S AUTHORITY TO OPERATE THE
EQUIPMENT.
THIS CLASS A DIGITALAPPARATUS COMPLIES WITH CANADIAN ICES-003.
CET APPAREIL NUMÉRIQUE DE LA CLASSE A EST CONFORME À LA NORME NMB-003 DU CANADA.
CE COMPLIANCE STATEMENT
WARNING: This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.

4
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. Apolarized plug has
two blades with one wider than the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong is provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified
by the manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused
for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has been
dropped.
15. CAUTION – THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALIFIED
SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF ELECTRIC SHOCK DO
NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE
OPERATING INSTRUCTIONS UNLESS YOU ARE QUALIFIED TO DO SO.
16. Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class 2
power source only.
17. ITE is to be connected only to PoE networks without routing to the outside plant.

5
Contents
1. Description ------------------------------------------------------------------6
1.1 Components - ------------------------------------------------------------------------------------------ 6
1.2 Key Features- ------------------------------------------------------------------------------------------ 7
2. Installation ------------------------------------------------------------------- 8
2.1 Overview----------------------------------------------------------------------------------------------------8
2.2 Connections-----------------------------------------------------------------------------------------------11
2.3 Network Connection and IP Assignment ---------------------------------------------------------- 13
3. Operation -------------------------------------------------------------------- 14
3.1 Access from a browser -------------------------------------------------------------------------------- 14
3.2 Access from the internet------------------------------------------------------------------------------ 15
3.3 Setting the admin password over a secure connection------------------------------------------- 15
3.4 Live View Page ----------------------------------------------------------------------------------------- 15
3.5 Network Camera Setup-------------------------------------------------------------------------------- 18
3.5.1 Basic Configuration ---------------------------------------------------------------------------- 18
1) Users------------------------------------------------------------------------------------------ 19
2) Network -------------------------------------------------------------------------------------- 20
3) Video & Image ------------------------------------------------------------------------------ 21
4) Date & Time --------------------------------------------------------------------------------- 24
3.5.2 Live View, Source------------------------------------------------------------------------------- 25
3.5.3 Video & Image---------------------------------------------------------------------------------- 26
3.5.4 Event---------------------------------------------------------------------------------------------- 32
1) Event-In -------------------------------------------------------------------------------------- 32
2) Event-Out ------------------------------------------------------------------------------------ 37
3) Event Map------------------------------------------------------------------------------------ 44
3.5.5 System ------------------------------------------------------------------------------------------ 45
1) Information ---------------------------------------------------------------------------------- 45
2) Security--------------------------------------------------------------------------------------- 46
3) Date & Time --------------------------------------------------------------------------------- 51
4) Network -------------------------------------------------------------------------------------- 52
5) Language------------------------------------------------------------------------------------- 61
6) Maintenance --------------------------------------------------------------------------------- 62
7) Support--------------------------------------------------------------------------------------- 63
3.6 Playback------------------------------------------------------------------------------------------------- 66
3.7 Help---- -------------------------------------------------------------------------------------------------- 68
3.8 Resetting to the factory default settings------------------------------------------------------------- 69
4. Appendix -------------------------------------------------------------------- 70
4.1 Troubleshooting ----------------------------------------------------------------------------------------- 70
4.2 Preventive Maintenance -------------------------------------------------------------------------------- 71
4.3 Product Specification ----------------------------------------------------------------------------------- 72

6
1. Description
The information in this manual provides quick installation and setup procedures for the Roughneck®
V921B/V922B Series of Bullet Cameras. These units should only be installed by a qualified technician
using approved materials in conformance with federal, state, and local codes. Read these instructions
thoroughly before beginning an installation. Always refer to Vicon’s website to assure you have the
most up-to-date manual, www.vicon-security.com.
The V921B/V922B Series of HD IP cameras is designed for demanding security installations. It offers a
number of fixed network camera versions that deliver crisp clear images to fit any installation need.
The V921B/V922B cameras are fully compatible with all ViconNet® systems; its ONVIF certification
provides an open-platform for integration into other video management systems.
The housing is designed for easy installation. PoE eliminates the need for power cables, providing a
cost-effective method of installation. The V920B features an auto iris lens that adapts to changing
outdoor lighting; the true day/night camera includes a removable IR cut filter. 32 IR LED illuminators
provide lighting up to 82 ft (25 m). The camera is IP67 rated with that withstands rain.
1.1 Components
The system comes with the following components:
Cameraunit InstallationCD InstallationQuick Guide Template Sheet Accessory Kit
Optional OSD Controller
Check your package to make sure that you received the complete system, including all components
shown above.
Note: Adapter for 12 VDC is not supplied and the optional V920D-OSD OSD Controller can be
purchased separately.

7
1.2 Key Features
• Brilliant video quality
The network camera offers the highly efficient H.264 video compression, which drastically
reduces bandwidth and storage requirements without compromising image quality. Motion JPEG
is also supported for increased flexibility.
• Dual or triple streams
The network camera can deliver dual or triple video streams simultaneously at full frame rate in
all resolutions up to full HD (1280 x 1080p) using Motion JPEG and H.264 (or MPEG-4). This
means that several video streams can be configured with different compression formats,
resolutions and frame rates for different needs.
• Image setting adjustment
The network camera also enables users to adjust image settings such as contrast, brightness and
saturation to improve images before encoding takes place.
• Wide Dynamic Range (V923B-IR39M only)
The network camera provides WDR (Wide Dynamic Range) that improves video exposure quality
in scenes with high contrast between bright and dark areas in the video, for example a shady
area and a sunny area in the same scene.
• Intelligent video capabilities
The network camera includes intelligent capabilities such as enhanced video motion detection.
The network camera’s external inputs and outputs can be connected to devices such as sensors
and relays, enabling the system to react to alarms and activate lights or open/close doors.
• Easy Focus
Easy Focus will be activated once Day/Night mode is switched and the focus readjusts
automatically.
• Focus & Zoom Control via Network
The network camera enables users to adjust focus and zoom remotely via the network.
• Resolution
V923B-IR39M (3 Megapixel): 2048x1536 @ 20 fps;
V922B-IR39M (2 Megapixel): 1920x1080 @ 30 fps;
V921B-IR39M (1 Megapixel): 1280x720 @ 30 fps;
• Micro-SD Recording support
The network camera supports a micro-SD memory slot for local recording with removable
storage.
• Improved Security
The network camera logs all user access and lists currently connected users. Also, its full frame
rate video can be provided over HTTPS.
• Power over Ethernet
Support for Power over Ethernet (IEEE802.3af) enables the unit, as well as the camera module
that is connected to it, to receive power through the same cable as for data transmission. This
makes for easy installation since no power outlet is needed.
• ONVIF
This is a global interface standard that makes it easier for end users, integrators, consultants,
and manufacturers to take advantage of the possibilities offered by network video technology.
ONVIF enables interoperability between different vendor products, increased flexibility, reduced
cost, and future-proof systems.

8
2. Installation
For the network camera to operate, it is necessary to connect a network cable for data transmission
and power connection from customer-supplied power supply.
2.1 Overview
Camera Dimensions
See the diagrams below for the exact dimension of the network camera dome.
Unit Dimensions: mm
Parts and Description

9
Sunshield Installation
The unit is shipped without the sunshield installed. Use the bolt supplied to secure the sunshield
to the body of the camera.
Base Installation
There are two ways of installing the camera.
1) Installation1 (Cable through the wall with the mount base)
A. Drill the mounting hole locations, using the template sheet (or the bottom of the mount base)
as a guide.
B. Insert the supplied plastic anchors into the holes.
C. Connect power cable and network line.
D. Align the screw holes of the mount base with the plastic anchors.
E. Use the mounting screws (M5x20) provided to secure the camera.
F. To adjust the camera position, loosen the mount screw (M6x16) to move the camera.
Retighten the screw when adjustment is complete.
1. Route cable through the wall to
mounting base. 3. Route cable through the cable
knockout tab in mounting base.
Loosen the mount screw (M6x16 mm)
PTS1, M5x20 Mounting Screws (3x)
Mounting Base
Plastic Anchors (3x)
Template Sheet
Wall

10
2) Installation 2 (Using the cable knockout tab in mount base)
A. Drill the mounting hole locations, using the template sheet (or the bottom of the mount base)
as a guide.
B. Insert the plastic anchors into the hole which has just drilled.
C. Connect connection cable and network lines.
D. Fit the screw holes of the mount base into the plastic anchors.
E. Remove the cable knockout tab for the cable entry.
F. Screw up the mount screws (M5x20).
G.To adjust the camera position, loosen the mount screw (M6x16) to move the camera.
Retighten the screw when adjustment is complete.
Remove the cable knockout tab for
cable entr
y
PTS1, M5x20 Mounting Screws (3x)
Mounting Base
Plastic Anchors (3x)
Template Sheet
Wall

11
2.2 Connections
Connection Cable
NO Wire Color Description
1 Red: 12 VDC
White: GND Main Power; 2 pin terminal, 12 VDC 2A (24W) with heater, or 12 VDC 320mA (3.8W) without heater
2 Black Ethernet; RJ-45 port compatible with 10/100Mbps having PoE
functionality. Modular jack.
Note: Heater requires 12 VDC. If using PoE, the heater will not operate.
• Connecting to the RJ-45
Connect a standard RJ-45 cable to the network port of the network camera. Generally a
cross-over cable is used for directly connection to PC, while a direct cable is used for connection
to a hub.
Arouter featuring PoE (Power over Ethernet) can be used to supply power to the camera.
Micro SD memory slot
Remove the rear cap of the camera to insert the SD memory card.
• Connecting the Power
Connect the 12 VDC power for the network camera. Connect the positive (+) pole to the ‘+’
position (red) and the negative (-) pole to the ‘-’ position (white) for the DC power.
Be careful not to reverse the polarity when you connect the power cable.
A router featuring PoE (Power over Ethernet) can be used to supply power to the camera.
The heater only operates when using the power source of 12 VDC.
If using PoE, the heater will not operate.
If PoE and 12 VDC are both applied, the camera will be supplied with power from PoE.

12
• Connecting Service Monitor Port
Service monitor port is used for easy OSD setup. To make changes in the OSD menu, use the
optional OSD controller
▶ID & IP assignment
To make changes in the OSD menu, the optional OSD controller (V920D-OSD) can be used to set
Camera Title and IP Address.
1. Connect the OSD Controller to the Service Monitor port of the network camera.
2. Connect Service Monitor and the Video Output port of the OSD Controller.
3. Press the SET button on the controller to access the Main Menu.
4. Change camera ID and IP address as needed. Additionally, the Name (or title) of the camera
can be changed. Use the ↑↓←→ buttons on the controller to change the parameters.
5. Select SAVE or CANCEL to exit the Main Menu.
The Video Output can also be used for easy zoom and focus control when adjusting the lens.
Video Output is restricted to 704x480 (576) resolution.
▶Zoom & Focus Control (Models with motorized lens)
The camera enters Zoom and Focus control mode when the OSD Controller is connected to the
Service Monitor port.
-.ZoomControl: ↑(Zoom In), ↓ (Zoom Out)
-.FocusControl: ← (Focus Near), → (Focus Far)
-. Fine Focus: Press and hold the SET button for at least 2 seconds. The camera readjusts
focus automatically.
Note: The optional V920D-OSD OSD Controller can be purchased separately.

13
2.3 Network Connection and IP assignment
The network camera is designed for use on an Ethernet network and requires an IP address for
access. Most networks today have a DHCP server that automatically assigns IP addresses to
connected devices. By the factory default, your camera is set to obtain the IP address automatically
via DHCP server. If your network does not have a DHCP server the network camera will use
192.168.1.100 as the default IP address.
If DHCP is enabled and the product cannot be accessed, run the “Smart Manager” utility on the CD to
search and allocate an IP address to your products, or reset the product to the factory default settings
and then perform the installation again.
1. Connect the network camera to the network and power up.
2. Start SmartManager utility (Start>All Programs>SmartManager>SmartManager); the main
window displays. After a short while any network devices connected to the network will be
displayed in the list.
3. Select the camera on the list and click right button of the mouse. The pop-up menu below
displays.
4. Select Assign IP. The Assign IP window displays. Enter the required IP address.
Note: For more information, refer to the Smart Manager
User’s Manual.

14
3. Operation
The network camera can be used with Windows® operating system and browsers. The recommended
browsers are Internet Explorer®, Safari®, Firefox®, Opera® and Google® Chrome® with Windows.
Note: To view streaming video in Microsoft® Internet Explorer, set your browser to allow ActiveX
controls.
Note: Some screens may appear different (i.e., color scheme) depending on the firmware version, but
the functionality is the same or similar.
3.1 Access from a Browser
1. Start a browser (i.e., Internet Explorer).
2. Enter the IP address or host name of the network camera in the Location/Address field of the
browser.
3. A starting page displays. Click Live View, Playback or Setup to select corresponding web page.
4. Click Live View for the network camera’s Live View page to appear in the browser.

15
3.2. Access from the Internet
Once connected, the network camera is accessible on your local network (LAN). To access the
network camera from the Internet you must configure your broadband router to allow incoming data
traffic to the network camera. To do this, enable the NAT-traversal feature, which will attempt to
automatically configure the router to allow access to the network camera. This is enabled from Setup
> System > Network > NAT.
For more information, refer to section “3.5.5 System>Network>NAT” of this manual.
3.3 Setting the Admin Password over a Secure Connection
T
o
g
ain access to the camera, the password for
t
he default administrator user must be set. This
is done in the “Admin Password” dialo
g
, which is
displayed when the network camera is accessed
f
or setup the first time. Enter your admin name
and password, set by the administrator.
Note: The default administrator username is
“
ADMIN” and password is “1234”. If the
password is lost, the network camera must be
reset to the factory default settings. See section
“
3.8 Resettin
g
to the Factory Default Settin
g
s” for
more details.
To prevent network eavesdropping when setting the admin password, it can be done via an encrypted
HTTPS connection, which requires an HTTPS certificate (see note below).
To set the password via a standard HTTP connection, enter it directly in the first dialog shown below.
To set the password via an encrypted HTTPS connection, see “3.5.5 System > Security > HTTPS”.
Note: HTTPS (Hypertext Transfer Protocol over SSL) is a protocol used to encrypt the traffic between
web browsers and servers. The HTTPS certificate controls the encrypted exchange of information.
3.4 Live View Page
T
he Live View page provides several
screen modes (camera model
dependant): 2048x1536, 1920x1080,
1280x1024, 1280x720, 704x480 (576),
640x480, 352x240 (288), and 320x240.
Select the most suitable mode in
accordance with your PC specifications
and monitorin
g
purposes.

16
1) General controls
LiveViewPage Search&PlaybackPage SetupPage HelpPage
The video drop-down list allows the selection of a customized or pre-
programmed video stream on the Live View page. Stream profiles are configured under Setup >
Basic Configuration > Video & Image. For more information, see section “3.5.1 Basic
Configuration > Video & Image” of this manual.
Theresolutiondrop-down list allows the selection of the most suitable
video resolutions to be displayed on Live View page.
Theprotocoldrop-downlistallowstheselectionofthecombinationof
protocols and methods to use depending on your viewing requirements and on the properties of
the network.
2) Control toolbar
The live viewer toolbar is available on the web browser page only. It displays the following
buttons:
The Stop button stops the video stream being played. Pressing the key again toggles the
start and stop. The Start button connects to the network camera or start playing a
video stream.
The Pause button temporarily stops (pauses) the video stream being played.
The Snapshot button takes a takes a picture (snapshot) of the current image. The location
where the image is saved can be specified.
The Digital Zoom button activates a zoom-in or zoom-out function for the video image on
the live screen.
The Full Screen button causes the video image to fill the entire screen area. No other
windows will be visible. Press the 'Esc' button on the computer keyboard to cancel full
screen view.
The Manual Trigger button activates a pop-up window to manually start or stop the event.
The Remote Focus button enables users to adjust focus and zoom remotely via network
(motorized lens models only).
The Fine Focus (one push focus) button readjusts focus automatically to set the focus to
the optimum position (motorized lens models only).

17
3) Video Streams
The network camera provides several image and video stream formats. Your requirements and
the properties of your network will determine the type you use.
The Live View page of the network camera provides access to H.264, MPEG-4 and Motion JPEG
video streams and to the list of available video streams. Other applications and clients can also
access these video streams/images directly, without going via the Live View page.
4) Focus and Zoom Control (Motorized Lens models only)
₩You can control Zoom and Focus from the Live View screen. Press the button on the left top in
the Live View screen to activate the Zoom and Focus control panel.
•Adjusting Zoom:
Click “<” button to zoom out and click “>” button to zoom in. The focus is moved slightly after
adjusting zoom; adjust the focus again, as necessary.
•Adjusting Focus:
Click “>” button for far focus and click “<” button to near focus.
•Fine Focus:
Click “Fine Focus” to fine tune and readjust focus automatically.
Note: Click the button in the Live View screen to set the focus to the optimum position.

18
3.5 Network Camera Setup
This section describes how to configure the network camera, and is intended for product
Administrators, who have unrestricted access to all the Setup tools, and Operators, who have access
to the settings for Basic, Live View, Video & Image, Event, and System Configuration.
The network camera is configured by clicking Setup in the top right-hand corner of the Live View page.
Click on this page to access the online help that explains the setup tools
When accessing the network camera for the first time,
the “Admin Password” dialog appears. Enter your admin
name and password, set by the administrator.
Note: If the password is lost, the network camera must
be reset to the factory default settings.
See “3.8 Resetting to the Factory Default Settings”.
The default administrator username is “ADMIN” and
password is “1234”.
3.5.1 Basic Configuration
The device information is displayed on this Basic Configuration page.

19
1) Users
User access control is enabled by default. An administrator can create additional users and passwords.
It is also possible to allow anonymous viewer login, which means that anybody may access the Live
View page, as described below:
The User List displays the authorized users and user groups (levels):
User Group Authority
Guest Provides the lowest level of access, which only allows access to the
Live View page.
Operator An operator can view the Live View page, create and modify events, and adjust certain other settings. Operators have no access
to System Options.
Administrator An administrator has unrestricted access to the Setup tools and can
determine the registration of all other users.
An administrator can Add, Modify or Remove users in the list by clicking the appropriate button. Click
Save to save the settings or Reset to cancel.
Enable anonymous viewer login: Check the box to use the webcasting features. Refer to
“3.5.3 Video & Image” for more details.
Enable WS-Security: Do not check this box to connect and monitor the network camera
through Vicon’s viewing software using drivers older than 935.
Note: WS-Security is an open format for signing and encryption of message parts, for supplying
credentials in the form of security tokens, and for security passing those tokens in a message.

20
2) Network
The network camera supports both IP version 4 and IP version 6. Both versions may be enabled
simultaneously, and at least one version must always be enabled. When using IPv4, the IP address for
the network camera can be set automatically via DHCP, or a static IP address can be set manually. If
IPv6 is enabled, the network camera receives an IP address according to the configuration in the
network router. There is also the option of using the Internet Dynamic DNS Service. For more
information on setting the network, refer to Setup> System>Security>Network.
• Obtain IP address via DHCP - Dynamic Host Configuration Protocol (DHCP) is a protocol
that lets network administrators centrally manage and automate the assignment of IP
addresses on a network. DHCP is enabled by default. Although a DHCP server is mostly
used to set an IP address dynamically, it is also possible to use it to set a static, known IP
address for a particular MAC address. Check the radio button to use this method.
• Use the following IP address - To use a static IP address for the network camera,
check the radio button and then make the following settings:
- IP address: Specify a unique IP address for the network camera.
- Subnet mask: Specify the mask for the subnet where the network camera is located.
- Default router: Specify the IP address of the default router (gateway) used for
connecting devices attached to different networks and network segments.
When the settings are complete, click Save, or click Reset to revert to previously saved settings.
Notes:
1. DHCP should only be enabled if using dynamic IP address notification, or if your DHCP server can
update a DNS server, which then allows access to the network camera by name (host name). If
DHCP is enabled and the unit cannot be accessed, it may have to be reset to the factory default
settings and then perform the installation again.
2. The ARP/Ping service is automatically disabled two minutes after the unit is started, or as soon as
an IP address is set.
3. Pinging the unit is still possible when this service is disabled.