Vicon V9360-1 User manual

www.vicon-security.com
XX271-10-01
V9360-1 Series
Network Hemispheric Camera
Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet your requirements or that the
operation will be entirely error free or perform precisely as described in the documentation. This system has not been designed
to be used in life-critical situations and must not be used for this purpose.
Vicon Industries Inc.
Tel: [phone] Fax: [phone] Toll Free: 800-645-9116
24-Hour Technical Support: 800-34-VICON (800-348-4266) UK: 44/(0) 1489-566300
Document Number: 8009-8271-10-01
Product specications subject to change without notice.
Issued: 116
Copyright © 2016 Vicon Industries Inc. All rights reserved.
User Guide

1
Table of Contents
1. Overview................................................................................................................................2
1.1 Features......................................................................................................................2
1.2 Package Contents .......................................................................................................3
1.3 Dimensions..................................................................................................................5
1.4 Connectors (Indoor Only).............................................................................................7
1.5 All-in-One Cable (Optional)..........................................................................................8
1.6 Function Cables (Outdoor Only) ..................................................................................8
2. Camera Cabling.....................................................................................................................9
2.1 Power Connection .......................................................................................................9
2.2 Ethernet Cable Connection..........................................................................................9
2.3 Waterproof Cable Connector.....................................................................................10
3. System Requirements ........................................................................................................12
4. Access Camera ...................................................................................................................13
5. Setup Video Resolution......................................................................................................17
6. Configuration Files Export / Import ...................................................................................18
7. Tech Support Information ..................................................................................................19
7.1 Delete the Existing Viewer.........................................................................................19
7.2 Setup Internet Security ..............................................................................................20
Appendix: Technical Specifications

2
1. Overview
The Hyper Fisheye IP Camera is a high resolution surveillance solution,
featuring 180° panoramic view (wall mount) or 360° panoramic view (ceiling
mount) without blind spots. The camera supports 6 Megapixels resolution
streaming at 30fps which guarantees smooth video viewing.With the embedded
180° wall and 360° ceiling mounting function plus multiple display modes, the
camera is suitable in locations such as transportations, shopping mall and
warehouse, etc.
Moreover, the dewarped images in panoramic view or other different viewing
modes can be recorded with edge dewarping function. Furthermore, with built-in
IR LED and noise reduction technique, the camera can deliver clear images in
low light conditions.
1.1 Features
Progressive Scan CMOS Sensor
Software Dewarping- 6MP + 720P real-time
Edge Dewarping, Up to 4M Resolution Real-time
Quad Streams Compression-
H.264 Baseline / Main / High Profile + MJPEG
Multiple Dewarp Display Modes-
Digital PTZ / Panorama View / Quad View
Smart Event Function-
Motion Detection / Network Failure Detection / Tampering Alarm / Periodical
Event / Manual Trigger / Audio Detection
Wide Dynamic Range
Smart Text Overlay and Privacy Masks
Day / Night (ICR)
IR LED Module
Built-in MIC & Speaker*
Weatherproof (IP66 International)*
microSD and NAS Recording Support
ONVIF Support
(*) Optional

3
1.2 Package Contents
Please check the package containing the following items listed below.
Indoor
Hyper Fisheye
IP Camera
Self-Tapping Screw
(x3)
Plastic Anchor
(x3)
Security Screw
(x1)
Security Torx Power Terminal
Block (x1)
Quick Guide CD
Function Cable (Optional)
NOTE: The supplied self-tapping screws are for soft substance /
material installation such as wood. For other installation environments
such as cement wall, it is required to pre-drill and use plastic anchors
before fastening the supplied self-tapping screws on the wall.

4
Outdoor
Hyper Fisheye
IP Camera
Self-Tapping Screw
(x3)
Plastic Anchor
(x3)
Security Screw
(x1)
Security Torx
Power Terminal
Block (x1)
Quick Guide CD
NOTE: The supplied self-tapping screws are for soft substance /
material installation such as wood. For other installation environments
such as cement wall, it is required to pre-drill and use plastic anchors
before fastening the supplied self-tapping screws on the wall.

5
1.3 Dimensions
The dimensions of the camera are shown below.
Indoor

6
Outdoor

7
1.4 Connectors (Indoor Only)
Please loosen the security screws and open the cover to reach the connectors.
The diagram below shows the connectors of the camera. Definition for each
connector is given as follows.
No.
Connector
Pin
Definition
Remarks
1
Power
(DC 12V / AC 24V)
1
DC 12V
AC 24V 1
Power connection
2
Reserved
AC 24V 2
2
RJ-45
-
For network and PoE connections
3 Alarm & Audio I/O
1
Alarm Out +
Alarm connection /
Two-way audio
transmission
2
Alarm Out –
3
Alarm In +
4
Alarm In –
5
-
6
Audio Out
7
Audio In
8
GND
4
Built-in
microphone
- Audio In
5
Speaker
-
Audio Out
6 Default Button -
Press the button with a proper tool for at least 20
seconds to restore the system.
7 microSD Card Slot -
Insert the microSD card into the card slot to store
videos and snapshots.
Do not remove the
microSD card when the camera is powered on.
NOTE: It is not recommended to record with the microSD card for 24/7
continuously, as it may not be able to support long term continuous data
read / write. Please contact the manufacturer of the microSD card for
information regarding the reliability and the life expectancy.

8
1.5 All-in-One Cable (Optional)
No.
Connector
Pin
Definition
Remarks
1 Alarm & Audio I/O -
Please refer to the Alarm & Audio I/O in
the table under Connectors.
2 Audio I/O
Pink
Audio In
Two-way audio
transmission
Green
Audio Out
3 Alarm I/O
(4-Pin Terminal Block)
1
Alarm In –
Alarm connection
2
Alarm In +
3
Alarm Out –
4
Alarm Out +
1.6 Function Cables (Outdoor Only)
No.
Connector
Pin
Definition
Remarks
1 Audio I/O
Pink
Audio In
Two-way audio
transmission
Green
Audio Out
2 Power (DC 12V / AC 24V)
(2-Pin Terminal Block)
Black
AC 24 V –
Power connection
DC 12V –
Red
AC 24V +
DC 12V +
3 Alarm I/O
(4-Pin Terminal Block)
1
Alarm In –
Alarm connection
2
Alarm In +
3
Alarm Out –
4
Alarm Out +
4
GND
-
GND
Ground connection
5
RJ-45
-
For network and PoE connections

9
2. Camera Cabling
Please follow the instructions below to complete the cable connections.
2.1 Power Connection
For power connection, please refer to section Connectors (Indoor Only) for the
indoor models, and see section Function Cables (Outdoor Only)for the outdoor
models. Alternatively, users can power the camera by PoE if a Power Sourcing
Equipment (PSE) switch is available. Refer to the section below for Ethernet
cable connection.
NOTE: If PoE is used, make sure PSE is in use in the network.
2.2 Ethernet Cable Connection
To have best transmission quality, cable length shall not exceed 100 meters.
Connect one end of the Ethernet cable to the RJ-45 connector of the camera,
and plug the other end of the cable to the network switch or PC.
NOTE: In some cases, Ethernet crossover cable might be needed when
connecting the camera directly to the PC.
Check the status of the link indicator and the activity indicator LEDs. If the LEDs
are unlit, please check the LAN connection.
Green Link Light indicates good network connection.
Orange Activity Light flashes for network activity indication.

10
2.3 Waterproof Cable Connector
Follow the instruction below to waterproof the connectors of different types of
cables. The supported cables are shown as below.
All-in-One Cable
of the Indoor Models
All-in-One Cable
of the Outdoor Models
IP66 RJ-45 Cable
(Outdoor Models Only)
All-in-One Cable of the Indoor Models / Outdoor Models
Follow the steps below to waterproof the connectors of theAll-in-One cable.
Step 1:
Connect the required devices to the All-in-One
cable and coat the joints with silicone gel. There
should be no gap between the connectors and
the cables. For the alarm I/O connector and the
power connector (outdoor models only)
, make
sure the side with
wires attached is also sealed
with silicone gel.
Indoor Models
Outdoor Models
For All-in-
One cable of the outdoor models,
attach the ground cable to the ground and wrap
the wires with silicone gel. Make sure the wires
are not exposed to the air.
Step 2:
Seal the end of the rubber coating of the
All-in-One
cable as indicated in the figure on
the right. Please use enough silicone gel to fill
in the hose and wrap around each wire;
otherwise, waterproof function cannot be
guaranteed.

11
IP66 RJ-45 Cable (Outdoor Models Only)
For IP66 RJ-45 cable, please use an RJ-45 IP66 plug for connection to prevent
water damage. Follow the steps below for cable connection.
Step 1:
Take out the supplied connector from the RJ-45
IP66 plug. Loosen the thread-
lock sealing nut
on the plug. Then thread the Ethernet cable
through the thread-
lock sealing nut and the
plug. If the Ethernet cable is already attached to
a connector, please remove it first.
Step 2:
Carefully remove a section of rubber coating
from the end of the Ethernet cable to reveal the
wires. Inset the wires to the correct pins of the
connector. Plug the Ethernet cable to the
connector of IP66 RJ-45 cable.
Step 3:
Fasten the RJ-
45 IP66 plug to the connector of
the IP66 RJ-
45 cable. Lastly, tighten the
thread-lock sealing nut to the plug.

12
3. System Requirements
To perform the IP camera via web browser, please ensure the PC is in good
network connection, and meet system requirements as described below.
Items System Requirement
Personal Computer
Minimum :
1. Intel®Core™ i5-2430M @ 2.4 GHz
2. 4 GB RAM
Recommended:
1. Intel®Core™ i7-870 @ 2.93 GHz
2. 8 GB RAM
Operating System Windows VISTA / Windows XP / Windows 7
Web Browser Microsoft Internet Explorer 6.0 or later
Firefox
Chrome
Safari
Network Card 10Base-T (10 Mbps), 100Base-TX (100 Mbps) or
1000Base-T (1000 Mbps) operation
Viewer ActiveX control plug-in for Microsoft IE

13
4. Access Camera
For initial access to the IP camera, users can search the camera through the
installer program: DeviceSearch.exe, which can be found in “DeviceSearch”
folder in the supplied CD.
Accessing the Camera by Device Search Software
Step 1: Double click on the program Device Search.exe.
Step 2: After its window appears, click on the <Device Search> button on the
top. All the finding IP devices will be listed in the page.
Step 3: Find the camera in the list by its IP address and click on it. The default
IP address of the camera is: 192.168.0.250.
Step 4: The default IP address of the camera may not be in the same LAN as
the IP address of the PC. If so, the IP address of the camera needs to
be changed. Right click on the camera and click <Network Setup>.
Meanwhile, record the MAC address of the camera, for future
identification.
Step 5: The <Network Setup> page will come out. Select <DHCP> and click
<Apply> down the page. The camera will be assigned with a new IP
address.
Step 6: Click <OK> on the Note of setting change. Wait for one minute to
re-search the camera.
Step 7: Click on the <Device Search> button to re-search all the devices. Find
the camera in the list by its MAC address. Then double click or right
click and select <Browse> to access the camera directly via a web
browser.

14
Step 8: A prompt window requesting for default username and password will
appear. Enter the default username and password shown below to
login to the camera.
Login ID
Password
Admin
1234
NOTE: ID and password are case sensitive.
NOTE: It is strongly advised that administrator’s password be
altered for the security concerns. Refer to the Hyper IP
Camera Menu Tree in the supplied CD for further details.
Installing Viewer Software Online
For initial access to the camera, a client program, Viewer, will be automatically
installed to the PC when connecting to the camera.
If the web browser doesn’t allow Viewer installation, please check the Internet
security settings or ActiveX controls and plug-ins settings (refer to section Setup
Internet Security) to continue the process.
The Information Bar (just below the URL bar) may come out and ask for
permission to install the ActiveX Control for displaying video in browser. Right
click on the Information Bar and select <Install ActiveX Control…> to allow the
installation.
The download procedure of Viewer software is specified as follows.
Step 1: In the Viewer installation window, click on <Next> to start
installation.
Step 2: The status bar will show the installation progress. After the installation
is completed, click on <Finish> to exit the installation process.
Step 3: Click on <Finish> to close the Viewer installation page.

15
Once the Viewer is successfully installed, the Home page of the IP camera will
be shown as the figure below.
Ceiling Mount Installed Camera

16
Wall Mount Installed Camera
NOTE:For more details about the function buttons on the Home page,
please refer to the Hyper IP Camera Menu Tree in the supplied CD.

17
5. Setup Video Resolution
Users can setup video resolution on Video Format page of the user-friendly
browser-based configuration interface.
Video Format can be found under this path: Streaming> Video Format.
The default video resolution of 5M and 6M models are shown as below. The
default resolution varies with different Fisheye Correction types, Front End
Correction (Edge Dewarping) and Back End Correction (Software Dewarping).
6M Front End
H.264- 2080 x 2048 (20 fps) + H.264- 1920 x 1080 (20 fps)
6M Back End
H.264- 1920 x 1080 (60/50 fps) + H.264- 720 x 480 (60/50 fps)
NOTE:For more details about the combinations of video resolution,
please refer to the Hyper IP Camera Menu Tree in the supplied CD.

18
6. Configuration Files Export / Import
To export / import configuration files, users can access the Maintenance page
on the user-friendly browser-based configuration interface.
The Maintenance setting can be found under this path: System> Maintenance.
Users can export configuration files to a specified location and retrieve data by
uploading an existing configuration file to the camera.
Export
Users can save the system settings by exporting the configuration file (.bin) to a
specified location for future use. Click on the <Export> button, and the popup
File Download window will come out. Click on <Save> and specify a desired
location for saving the configuration file.
Upload
To upload a configuration file to the camera, click on <Browse> to select the
configuration file, and then click on the <Upload> button for uploading.

19
7. Tech Support Information
This chapter will introduce how to delete previously-installed Viewer in the PC
and how to setup the Internet security.
7.1 Delete the Existing Viewer
For users who have installed the Viewer in the PC previously, please remove
the existing Viewer from the PC before accessing to the IP camera.
Deleting the Viewer
In the Windows <Start Menu>, activate <Control Panel>, and then double click
on <Add or Remove Programs>. In the <Currently installed programs> list,
select <Viewer> and click on the button <Remove> to uninstall the existing
Viewer.
Deleting Temporary Internet Files
To improve browser performance, it is suggested to clean up all the files in the
<Temporary Internet Files>. The procedure is as follows.
Step 1: In the web browser, clicks on the <Tools> tab on the menu bar and
select <Internet Options>.
Step 2: Click on the <Delete> button under <Browsing History> section. In the
appeared window, tick the box beside the <Temporary Internet files>.
Step 3: Click on <Delete> to start deleting the files.