Vicon V988D User manual


Vicon Industries Inc. does not warrant that the functions contained in this equipment will
meet your requirements or that the operation will be entirely error free or perform
precisely as described in the documentation. This system has not been designed to be
used in life-critical situations and must not be used for this purpose.
Document Number: 8009-8305-20-00 Product specifications subject to change without
notice. Issued: 6/18 Copyright © 2018 Vicon Industries Inc. All rights reserved.
Vicon Industries Inc.
Tel: [phone])
Fax: [phone]
Toll Free: 800-645-9116
24-Hour Technical Support:
800-34-VICON
QUICK INSTALLATION GUIDE
XX305-20-00
V988D
Network 4K Dome Camera
Quick Guide

WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EX-
POSE THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY
METALLIC OBJECT THROUGH THE VENTILATION GRILLS OR OTHER
OPENNINGS ON THE EQUIPMENT.
CAUTION
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an equilateral triangle, is in-
tended to alert the user to the presence of dangerous voltage within the products
enclosure that may be of sufficient magnitude to constitute a risk of electric shock
to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing) instructions
in the literature accompanying the product.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
2

FCC COMPLIANCE STATEMENT
CE COMPLIANCE STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC INFORMATION: This equipment has been tested and found to
comply with the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the
interference at his own expense.
CAUTION: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil nume
`
rique de la classe A est conforme a
´
la norme NMB-003 du
Canada.
WARNING
This is a Class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
3

IMPORTANT SAFETY INSTRUCTIONS
1. Readtheseinstructions.
2. Keeptheseinstructions.
3. Heedallwarnings.
4. Followallinstructions.
5. Donotusethisapparatusnearwater.
6. Cleanonlywithdrycloth.
7. Donotblockanyventilationopenings.Installinaccordancewiththemanufacturerinstructions.
8. Donotinstallnearanyheatsourcessuchasradiators,heatregisters,stoves,or other  apparatus
(includingamplifiers)thatproduceheat.
9. Donotdefeatthesafetypurposeofthepolarizedorgrounding‐typeplug.Apolarized  plughastwo
bladeswithonewiderthantheother.Agroundingtypeplughastwo blades
 andathirdgroundingprong.
Thewidebladeorthethirdprongareprovidedforyoursafety.
 Iftheprovidedplugdoesnotfitintoyour
outlet,consultanelectricianforreplacementofthe
 obsoleteoutlet.
10. Protectthepowercordfrombeingwalkedonorpinchedparticularlyatplugs,convenience
receptacles,andthepointwheretheyexitfromtheapparatus.
11. Onlyuseattachments/accessoriesspecifiedbythemanufacturer.
12. Useonlywiththecart,stand,tripod,bracket,ortablespecified  bythe
manufacturer,orsoldwiththeapparatus.Whenacartis used.
 Usecautionwhen
movingthecart/apparatuscombinationtoavoid injuryfromtip‐over.
13. Unplugthisapparatusduringlightningstormsorwhenunused for  long
periodsoftime.
14. Referallservicingtoqualifiedservicepersonnel.Servicingisrequired when the apparatus has been
damaged in any way,such as
 power‐supply cordor plugisdamaged, liquid hasbeenspilled orobjects
havefallenintotheapparatus,theapparatushasbeenexposedtorainormoisture,
 doesnotoperate
normally,orhasbeendropped.
15. CAUTION−THESESERVICINGINSTRUCTIONSAREFORUSEBY QUALIFIED
SERVICEPERSONNELONLYTOREDUCETHERISKOFELECTRICSHOCKDO NOT
 PERFORMANYSERVICING
OTHERTHANTHATCONTAINEDINTHEOPERATINGIN‐
 STRUCTIONSUNLESSYOUQREQUALIFIEDTODOSO.
16. Usesatisfyclause2.5ofIEC60950‐1/UL60950‐1orCertified/ListedClass2power  sourceonly.
17. ITEistobeconnectedonlytoPoEnetworkswithoutroutingtotheoutsideplant.
4

1 Introduction
Vicon’s V988D-W311MIR HD IP Dome Camera is designed for performance in demanding security installations.
The camera provides 4K (8 MP) resolution with a 3.6-11 mm motorized varifocal lens. The camera offers IR
illuminators that provide superior images in low-light environments.
The V988D-W311MIR supports H.264/H.265 compression technology, drastically reducing file sizes and
conserving valuable network bandwidth. M-JPEG compression is also provided. The camera can provides quad
streaming for multi-camera displays.
1.1 Components
Thissystemcomeswiththefollowingcomponents;  Network
Camera 1
InstallationGuide 1
TemplateSheet 1
AccessoryKit 1
Note 1. Check your package to make sure that you received the complete system, including all components
listed above.
Note 2. Adapter for 12 VDC is not supplied.
5

2 Installation
For the operation of the network c amera, it is necessary to connect a network cable for data
transmission, power connection from power adapter. Depending on operation
methods, it is possible to
connect an alarm cable additionally. For its fixation on different
locations, please consult with an installer.
2.1 Overview
• Dimension
Dimensions Unit: mm
• Extension Cable
No. Item Description
1 RJ-45
Ethernet, RJ-45 port compatible
with 10/100Mbps PoE Modular Jack
2 DC Jack Main Power, DC Jack, 12 VDC
3
AI: Alarm In
Alarm input and output, 3-pin terminal
G: GND
AO: Alarm Out
4
MIC: Audio In
Audio line input, 2-pin terminal
G: GND
5
SPK: Audio Out
Audio line output, 2-pin terminal
G: GND
6

• Installing & Adjusting Camera
Carefully remove the contents from the box.
1) Loosen the four torx screws located on the front of the housing, leaving the screws intact in the
front portion.
2) Using the template sheet, make mounting holes and cable hole in the location (ceiling or wall) where
this dome camera is being installed.
Do not continue to turn the camera in same direction.
The cable connector can be detached.
7

2.2 Connection
• Micro SD memory slot on the bottom board
Remove the cap at bottom of the camera to insert the SD memory card.
• Connecting to the RJ-45
Connect a standard RJ-45 cable to the network port of the network camera. Generally a cross-over cable is
used for directly connection to PC, while a direct cable is used for
connection to a hub. You can also use a
router featuring PoE (Power over Ethernet) to
supply power to the camera.
• Connecting Alarms
AI (Alarm In): You can use external devices to signal the network camera to react on events. Mechanical or
electrical switches can be wired to the AI (Alarm In) and G
(Ground) connectors.
G (Ground): Connect the ground side of the alarm input and/or alarm output to the G
(Ground) connector.
AO (Alarm Out): The network camera can activate external devices such as buzzers
or lights. Connect the
device to the AO (Alarm Out) and G (Ground) connectors.
• Connecting the Power
Connect the power of 12VDC for the network camera. Connect the positive (+) pole to the ‘+’ position and the
negative (-) pole to the ‘-’ position for the DC power.
– Be careful not to reverse the polarity when connecting the power cable.
– A router featuring PoE (Power over Ethernet) can also be used to supply power to the camera.
– For the power specifications, refer to the appendix, product specification intheUsermanual.
– If PoE and 12 VDC are both applied, the camera will be supplied with power from PoE.
• Connecting Audio
Connect speaker to audio line output and external Mic to audio input line.
8

2.3 Resetting to the factory default settings
To reset the network camera to the original factory settings, go to the Setup > System > Maintenance web
page (described in “System
> Maintenance” of User Manual) or use the Reset button on the network
camera inside the bottom cap.
• Using the Reset button:
Follow the instructions below to reset the network camera to the factory default settings using the Reset
button.
1) Switch off the network camera by disconnecting the power adapter.
2) Open the top cap.
3) Press and hold the Reset button with a straightened paperclip while reconnecting the power.
4) Keep the Reset button pressed at least 5 (or more) seconds.
5) Release the Reset button.
6) The network camera resets to factory defaults and restarts after completing the factory reset.
7) Close the bottom cap tightly to ensure waterproof.
CAUTION: When performing a Factory Reset, you will lose any settings that have been
saved. (Default
IP 192.168.30.220)
9

2.4 Network Connection & IP Assignment
ThenetworkcameraisdesignedforuseonanEthernetnetworkandrequiresanIPaddressforaccess.Most
networkstodayhaveaDHCPserverthatautomaticallyassignsIPaddressestoconnecteddevices.Bythe
factorydefault,yourcameraissettoobtaintheIPaddressautomaticallyviaDHCPserver.Ifyournetwork
doesnothaveaDHCPserverthenetworkcamerawilluse192.168.1.100asthedefaultIPaddress.
IfDHCPisenabledandtheproductcannotbeaccessed,runthe“SmartManager”utilitytosearchand
allocateanIPaddresstoyourproducts,orresettheproducttothefactorydefaultsettingsandthenperform
theinstallationagain.TheutilitycanbefoundontheViconwebsitewww.vicon‐security.com,onthe
SoftwareDownloadspageforViconcameras.
1) Connect the network camera/device to the network and power up.
2) Start SmartManager utility (Start > All programs > SmartManager > SmartManager). ); the main window
displays. After a short while any network devices connected to the network will be displayed in the list.
3) Select the camera on the list and click right button of the mouse. The pop-up menu below displays.
4) Select Assign IP Address. The Assign IP window displays. Enter the required IP address.
NOTE: For more information, refer to the SmartManager User Manual.
10