Vicon Cruiser SN660V Operating instructions

II
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO
NOT INSERT ANY METALLIC OBJECTS THROUGH THE
VENTILATION GRILLS OR OTHER OPENINGS ON THE
EQUIPMENT.
CAUTION
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to
the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral is
intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.

III
FCC COMPLIANCE STATEMENT
FCC INFORMATION: This equipment has been tested and found
to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the
equipment is o
perated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to
correct the interference at his own expense.
CAUTION: Changes or modifications not expressly approved by
the party responsible for compliance could void the user’s authority
to operate the equipment.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme
NMB-003 du Canada.
CE COMPLIANCE STATEMENT
WARNING
This is a Class A product. In a domestic environment this product
may cause radio interference in which case the user may be
required to take adequate measures.

IV
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other. A
grounding type plug has two blades and a third grounding prong. The
wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from
the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid injury
from tip-over.
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-
supply cord or plug is damaged, liquid has been moisture, does not
operate normally, or has been dropped.
15. CAUTION – THESE SERVICING INSTRUCTIONS ARE FOR USE
BY QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE
RISK OF ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING
OTHER THAN THAT CONTAINED IN THE OPERATING
INSTRUCTIONS UNLESS YOU QRE QUALIFIED TO DO SO.
16. Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or
Certified/Listed Class 2 power source only.

V
Table of Contents
Chapter 1 — Introduction...........................................................................................................1
1.1 Features .............................................................................................................................................1
Chapter 2 — Installation and Configuration.........................................................................2
2.1 Package Contents............................................................................................................................2
2.2 Installation.........................................................................................................................................3
2.3 Basic Configuration of Dome Camera System........................................................................5
2.4 Setting Dome Camera Address (ID)............................................................................................6
2.5 Connections......................................................................................................................................6
2.6 IP Assignment..................................................................................................................................7
2.7 Getting Started .................................................................................................................................8
Chapter 3 — Program and Operation.....................................................................................9
3.1 Dome Camera Selection ................................................................................................................9
3.2 Accessing the On-Screen Menu Utility......................................................................................9
3.3 How to control the On-Screen Menu Utility..............................................................................9
3.4 Auto Scan (Shortcut: P60P)........................................................................................................10
3.5 Preset (Shortcut: P93P)...............................................................................................................12
3.6 Tour (Shortcut: P70P)...................................................................................................................14
3.7 Pattern (Shortcut: P80P)..............................................................................................................15
3.8 Area Title..........................................................................................................................................16
3.9 Privacy Zone...................................................................................................................................17
3.10 Camera Menu................................................................................................................................18
3.11 Dome Setup...................................................................................................................................21
3.12 Dome Communication ...............................................................................................................27
3.13 Function Run................................................................................................................................28
Chapter 4 — Operation by Web Browser ............................................................................29
4.1 Access from a browser................................................................................................................29
4.2 Access from the internet.............................................................................................................30
4.3 Setting the admin password over a secure connection......................................................30
4.4 Live View Page...............................................................................................................................30
4.5 Network Camera Setup................................................................................................................32
4.5.1 Basic Configuration...............................................................................................................33
1) Users..........................................................................................................................33
2) Network......................................................................................................................34
3) Video & Image ...........................................................................................................35
4) Audio..........................................................................................................................37
5) Date & Time ...............................................................................................................38

VI
4.5.2 Video & Image.........................................................................................................................39
1) Basic ..........................................................................................................................39
2) Image..........................................................................................................................39
3) Webcasting................................................................................................................40
4.5.3 Audio .........................................................................................................................................41
4.5.4 Event..........................................................................................................................................41
1) Event-In......................................................................................................................41
2) Event-Out...................................................................................................................45
3) Event Map..................................................................................................................52
4.5.5 System ......................................................................................................................................54
1) Information ................................................................................................................54
2) Security......................................................................................................................54
3) Date & Time ...............................................................................................................57
4) Network......................................................................................................................58
5) Language...................................................................................................................67
6) Maintenance ..............................................................................................................67
7) Support......................................................................................................................68
4.6 PTZ Control.....................................................................................................................................69
4.7 Playback...........................................................................................................................................70
4.8 Help ...................................................................................................................................................72
4.9 Resetting to the factory default settings.................................................................................73
4.10 System Requirement for Web Browser.................................................................................73
Appendix A — Specifications.................................................................................................74
Appendix B — Troubleshooting.............................................................................................77
Shipping Instructions ...............................................................................................................78
Vicon Standard Equipment Warranty...................................................................................79

1
Chapter 1 — Introduction
1.1 Features
•Built-in optical power zoom camera with True Night Shot function
•Dual or Triple video streams simultaneously at full frame rate in all resolutions up to D1
(720X480 in NTSC, 720X576 in PAL) using Motion JPEG and H.264 (or MPEG-4)
•Intelligent capabilities such as enhanced video motion detection
The encoder’s external inputs and outputs can be connected to devices such as sensors and
relays, enabling the system to react to alarms and activate lights or open/close doors.
•ONVIF: This is a global interface standard that makes it easier for end users, integrators,
consultants, and manufacturers to take advantage of the possibilities offered by network video
technology. ONVIF enables interoperability between different vendor products, increased
flexibility, reduced cost, and future-proof systems.
•Supports two-way audio
•Logs all user access, and lists currently connected users. Also, full frame rate video can be
provided over HTTPS.
•Interface Protocol: TCP/IP, UDP, IPv4/v6, HTTP, HTTPS, QoS, FTP, uPnP, RTP, RTSP, RTCP,
DHCP, ARP
•240 Preset positions with the individual camera AE setup
•8 Tours consist of Presets, Patterns, Auto Scans and other Tours can be programmed with
over 300 functions and preset locations. While moving, each Preset scan can be watched in
smooth Vector Scan mode.
•16 Auto Scans with the normal, the vector, and the random mode and the endless auto-pan
(continuous rotation) with 13 speed steps
•8 Patterns (up to 200 second) and 8 Privacy Zones
•16 Area Titles
•1 Alarm input/1 Alarm output
•Variable speed from 0.1°/sec to 380°/sec
Three variable speeds (SLOW, NORMAL, TURBO)
•Pan/Tilt speed is inversely proportional to the zoom ratio.
•Maximum speed is 380°/sec with preset command.
•Auto Calibration from 0.1°to 6°(Tilt range is 0°to 180°)
•Programmable user preferences (alarm, preset, title, etc.)
•180°Digital Flip
•Up to 255 selectable camera addresses
•Multi-language menu display; password confirmation
•Function Run menu using DVR without function key (Pattern, Scan, etc.)
•Built-in RS-485 receiver driver
•24 VAC or 12 VDC for dome
•Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class 2 power source only.

2
Chapter 2 — Installation and Configuration
2.1 Package Contents
The dome camera is designed with a compact, small size, hard dome camera housing.
The housing is constructed of aluminum, steel and plastic. The housing is designed to be
mounted on a wall or a ceiling. The housing meets the Protection Classification IP66 standards
for dust and moisture resistance.
* Dome Camera 1
* Installation Guide/CD 1
* Template Sheet 1
* Mounting Bracket 1
* Safety Lanyard 1
* Accessory Kit 1
1) Mounting screws (PH6 x 35.0) (4)
2) Plastic anchors (4)
3) O-Rings (4)
4) Torx wrench (1)
* Accessory Connector 1
1) 3-Pin Terminal Block (1)
2) 6-Pin Terminal Block (1)

3
2.2 Installation
The dome camera is for use in surface or pendant mounting applications, and the mounting
surface must be capable of supporting loads of up to 3.5 lb (1.6 kg). (Pendant mounting must use
pendant mount accessory.)
The dome camera’s mounting bracket should be attached to a structural object, such as hard
wood, wall stud or ceiling rafter, that supports the weight of the dome camera.
CAUTION: A silicone rubber sealant must be applied to seal the housing to secure
waterproofing.
2.2.1 Locking Dome Camera – refer to the Figures that follow
A. Make screw holes on the ceiling using the supplied mounting Template Sheet (Figure A).
B. Fix the Mounting Bracket to the ceiling using supplied Anchors (4x) and Mounting Screws (4x)
(Figure B).
C. Hook the Safety Lanyard to the Safety Lanyard Hook of the Mounting Bracket (Figure C).
D. Align the locking tab on the bracket and the locking slot on the base of the dome (Figure D).
E. Turn the dome counterclockwise about 10 degrees to the locked position (Figure E).

4
CAUTION: Before installing mounting bracket to surface, pre-adjust the four mounting
screws "A" on the base of the dome camera to best match the mounting
bracket locked position. Unscrew the locking screw on the side of the dome's
base and fit the tab of the mounting bracket into the locking slot. Screws "A"
should not be too tight or too loose when the dome is in the locked position.
After setting the proper positions of screws "A" remove the mounting bracket
and install it to the proper surface. If it is too difficult to lock the dome in
position after the mounting bracket has been installed readjust the screws "A"
by unscrewing them a small amount and try to install dome camera again.

5
2.3 Basic Configuration of Dome Camera System
No. Wire Color Description
1 Red: 24 VAC or 12 VDC+
White: 24 VAC or 12 VDC- Main Power: 3-Pin terminal
2
Black: GND
Gray: Alarm Input
Yellow: GND
Black&White: Alarm Output
Green: RS485+
Blue: RS485-
Alarm Input/Output, RS485: 6-Pin terminal
3 Black Ethernet: RJ45 Modular Jack
4 BNC Black Video Composite Output: BNC Jack
5 RCA Gray Audio line output: RCA Jack
6 RCA Black Audio line input: RCA Jack
The dome camera must be installed by qualified service personnel in accordance with all local
and federal electrical and building codes.

6
2.4 Setting Dome Camera Address (ID)
To prevent damage, each dome camera must have a unique address (ID).
When installing multiple dome cameras using a multiplexer, it is suggested that the dome camera
address match the multiplexer port number.
The factory default setting is 1.
Refer to ‘3.13 Dome Communication’ section for detailed information.
2.5 Connections
• Connecting to the RJ-45
Connect a standard RJ-45 cable to the network port of the dome camera. Generally a cross-
over cable is used for directly connection to PC, while a direct cable is used for connection to a
hub.
• Connecting Alarms
AI (Alarm Input)
You can use external devices to signal the dome camera to react on events. Mechanical or
electrical switches can be wired to the AI (Alarm Input) and G (Ground) connectors.
Please see “4.5.4 Event > 1) Event-In > ②Alarm In” for configuring alarm input.
G (Ground)
NOTE: All the connectors marked G or GND are common.
Connect the ground side of the alarm input and/or alarm output to the G (Ground) connector.
AO (Alarm Output)
The dome camera can activate external devices such as buzzers or lights. Connect the device
to the AO (Alarm Output) and G (Ground) connectors.
Please see “4.5.4 Event > 2) Event-Out > ④Alarm Out” for configuring alarm output.
• Connecting to the RS485
The dome camera can be controlled remotely by an external device or control system, such as
a control keyboard, using RS485 half-duplex serial communications signals.
• Connecting Video Output connector
Connect the video output (BNC) connector to the monitor or video input.
• Connecting the Power
Connect the power of 24 VAC or 12 VDC 1A for the dome camera.
When using a 12 VDC adapter, connect the positive (+) pole to the “+” position and
the negative (-) pole to the “-” position.
Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class 2 power source only.

7
2.6 IP Assignment
When the dome camera, encoder or decoder is first connected to the network it has no IP
address. So, it is necessary to allocate an IP address to the device with the “SmartManager”
utility on the CD.
1. Connect the dome camera/device to the network and power up.
2. Start SmartManager utility (Start > All programs > SmartManager > SmartManager). The main
window will display, and after a short while any network devices connected to the network will
be displayed in the list.
3. Select the dome camera on the list and click right button of the mouse.
You can see the pop-up menu as below.
4. Select Assign IP Address. The Assign IP window will display. Enter the required IP address.
Note:For more information, refer to the SmartManager User’s Manual.

8
2.7 Getting Started
Once installed apply power to the dome camera. The dome camera will start a configuration
sequence.
OSD Position
The dome can move the OSD position in the OSD position setup.
(AREA TITLE) (AF AE)
(FUNC TITLE )
(CTRL KEY TO MOVE)
SAVE AND EXIT(ESC TO CANCEL)
(DOME ID…)
(ANGLE…)
OSD Position Setup
ABC AF AE
001
EMPTY DATA
DOMEID:001
W→360.0 090.0
INFORMATION
DISPLAY
CAMERA TITLE
CAMERA ID
VIEW DIRECTION
PAN & TILT ANGLE
STATUS of
FOCUS and AE
AREA TITLE
FUNCTION TITLE

9
Chapter 3 — Program and Operation
Note: The use of certain keypads may limit the functionality of the unit, for example the number
of available presets or patterns.
3.1 Dome Camera Selection
Before you program or operate a dome camera, you must select the dome camera by pressing
No. + CAM keys.
Example:Pressing 1, 0+ CAM keys sequentially will select dome camera 10. The selected
dome camera ID will be displayed on the LCD monitor of the keyboard controller.
3.2 Accessing the On-Screen Menu Utility
You can call up the On-screen menu utility (OSD) on your monitor by pressing the P95P key on
the keyboard controller; the following on-screen menu utility will appear:
Note: Throughout this manual, P**P (where ** is the Preset number) means pressing the Preset
key, entering the Preset number and then pressing the Preset key again.
DOME MENU
AUTO SCAN
PRESET
TOUR
PATTERN
AREA TITLE
PRIVACY ZONE
CAMERA
DOME SETUP
DOME COMMUNICATION
FUNCTION RUN
EXIT(ESC TO EXIT)
3.3 How to control the On-Screen Menu Utility
Function Button
Call the On-screen menu utility. P95P
Navigate through the menu items. Joystick up or down
Go into the sub-menu items. Joystick left or right or Open IRIS
Change value.
Enter the editing title mode.
Joystick left or right or
ZOOM In , ZOOM Out
Change value of angle. Open IRIS + Joystick
Enter the changing angle mode. Open IRIS
Exit the changing angle mode. Close IRIS
Escape (EXIT) P96P

10
3.4 Auto Scan(Shortcut: P60P)
The Auto Scan supports up to 17 programmed angles at user-programmable speeds.
Follow these steps to program Auto Scan:
AUTO SCAN SETUP
NUMBER : 01
TITLE : A01
MODE : NORMAL
SPEED : 5 STEP
START ANGLE : ----- -----
END ANGLE : ----- -----
SCAN DIR : CCW
SWAP : OFF
DWELL : 03 SEC
SAVE AND EXIT(ESC TO CANCEL)
NUMBER: 01 ~ 08, 10 ~ 17, 09: AUTO-PAN mode
TITLE: Up to 12 characters.
MODE: NORMAL, VECTOR, RANDOM (AUTO-PAN mode: NORMAL, RANDOM only).
NORMAL: Move from start point to end point, panning only.
VECTOR: Move from start point to end point including tilt and zoom simultaneously and
linearly.
RANDOM: Move randomly between the start point and the end point.
SPEED: 1 ~ 13 step, the lower number means the slower speed.
SCAN DIR: Set the Scan direction, CCW (counter-clockwise), CW (clockwise).
SWAP: Swap the start point for the end point.
DWELL: Set the dwell time at the both end, 01 ~ 99 seconds.
1. Press the P60P key to enter the Auto Scan menu directly. Or press the P95P key to display
the main menu on the monitor. Scroll to Auto Scan and push the Joystick to the right.
2. Select “NUMBER” and set the desired number by pushing the Joystick to the left or right.
3. Select “TITLE” and ZOOM In to enter the title edit mode.
4. ZOOM In or ZOOM Out to change the alphanumeric characters and move Joystick left or
right to the next position. Or move down to the character table and press the Open IRIS key at
the desired character; the cursor position then moves to the next position automatically. Push
the Joystick to the left or right at the “ALL DELETE” field to delete all characters. Push the
Joystick to the left or right at the “EXIT” field to finish title edit menu.
TITLE EDIT MENU
A01
*
A B C D E F G H I J
K L M N O P Q R S T
U V W X Y Z 0 1 2 3
4 5 6 7 8 9 ( )
ALL DELETE
EXIT(ESC TO EXIT)
5. Select “MODE” and “SPEED”.

11
6. Select “START ANGLE”. Press the Open IRIS key; the “CTRL” displays. Move to the desired
position and the zoom position. Press the Close IRIS key; the “CTRL” disappears. To adjust
at the 0.1 degree interval, ZOOM In/Out Joystick at the pan field and the tilt field. To adjust at
the one zoom interval, ZOOM In/Out Joystick at the zoom field.
7. Select “END ANGLE”. Press the Open IRIS key; the “CTRL” displays. Move to the desired
position and the zoom position. Press the Close IRIS key; the “CTRL” disappears. To adjust
at the 0.1 degree interval, ZOOM In/Out Joystick at the pan field and the tilt field. To adjust at
the one zoom interval, ZOOM In/Out Joystick at the zoom field.
8. Set “SCAN DIR” to CCW or CW.
9. Select “SWAP”; set to ON to exchange the start angle and the end angle.
10. Set “DWELL TIME”.
11. Select “SAVE AND EXIT” and push the Joystick to the right or press the Open IRIS key.
Press the Close IRIS key to exit the program without saving.
To set the position using the Preset position:
a. Before entering the Auto Scan menu, select a Preset position as a starting point for Auto Scan.
Example:P2P keys and do steps 1 to 5. In step 6, just press the Open IRIS key at the start
angle position; the current position will be displayed as a start position.
b. Press Close IRIS to Save and Exit from the menu.
Press the P60P key on the angle field to display with the small OSD. Then the screen will display
as below.
AUTO SCAN AREA SETUP
(CTRL KEY)
NUMBER01
START : ----- -----
END : ----- -----
EXIT(ESC TO EXIT)
The setting procedure is the same as above.
NOTE: 09: AUTO-PAN mode (endless panning/continuous rotation)

12
3.5 Preset (Shortcut: P93P)
If you need to view specific places routinely, you should program Presets. A Preset is a
programmed video scene with automatic pan, tilt, zoom, focus, and AE settings. Once
programmed, pressing the Preset key, preset number and then preset key again calls up that
Preset automatically. In addition, Presets may be assigned the “home” position for the dome
camera. As many as 240 Presets, whose positions are saved in the dome’s firmware, may be
programmed.
There are three pages of Preset menu. Each page has 80 Presets. Pages can be scrolled by
pushing the Joystick to the left or right on the first or last No. of Preset.
PRESET SETUP
NUMBER : 001
TITLE : ---
CAMERA SET
DWELL : -- SEC
12345678901234567890
00 █**-----------------
02 --------------------
04 --------------------
06 --------------------
NEXT PAGE
SAVE AND EXIT(ESC TO CANCEL)
-: blank Preset position
*: position has the Preset
█: current cursor position
Follow steps below to store the Preset positions:
1. Press the P93P key to enter the Preset menu directly. Or press the P95P key to display the
main menu on the monitor. Scroll to Preset and push the Joystick to the right.
2. Select the blank Preset position to be stored by pushing the Joystick up, down, right, or left.
3. After selecting a blank position, press the Open IRIS key. Use the Joystick to control the
direction of the camera and lens.
4. After aiming the camera (view direction and lens control), press the Close IRIS key. The
cursor will be on the “TITLE”; after saving data, twist the Joystick or press the ZOOM in or
ZOOM Out key to edit the Preset title. Follow the procedure in Auto Scan, above, to edit titles.
5. Select “CAMERA SET” and push the Joystick to the left or right. The Preset camera setup
displays.
PRESET CAMERA SETUP
FOCUS : AUTO
AE SETUP
SAVE AND EXIT(ESC TO CANCEL)
Set FOCUS: AUTO, MANUAL, ONE PUSH

13
Select “AE SETUP” and push the Joystick to the left or right. The AE setup displays.
Refer to the AE SETUP in the camera setup.
6. Set “DWELL TIME”. (03 ~ 99 seconds)
7. To select the next page of Presets, scroll the page by pushing the Joystick to the left on the
first and last columns of the menu.
8. Repeat step 2 through 7 for each additional Preset position.
9. Select “SAVE AND EXIT” and push the Joystick to the right or press the Open IRIS key.
Press the Close IRIS key to exit the program without saving.
The position, which is marked with the *, already has the Preset view assigned. Press the P93P
key on the *to review the stored Preset. The camera will show the stored Preset scene.
PRESET AREA SETUP
(CTRL KEY)
NUMBER 001
PAN TILT
000.0 000.0
EXIT(ESC TO EXIT)
Press the Open IRIS key; the “CTRL” displays. Move to the desired position and the zoom
position. Press the Close IRIS key; the “CTRL” disappears. Select “EXIT” and push the
Joystick to the right.

14
3.6 Tour (Shortcut: P70P)
There are 8 programmable Tours. Each Tour consists of up to 42 Preset positions, Patterns,
Scans or other Tours (second-level). Using second-level Tours, there can be over 300 functions
in a single tour.
TOUR SETUP
NUMBER : 01
TITLE : T01
SCAN TYPE : NORMAL
SPEED : 5 STEP
DWELL : -- SEC
003 A04 --- --- --- --- ---
--- --- --- --- --- --- ---
--- --- P01 --- --- --- ---
--- T02 --- --- --- --- ---
--- --- --- --- --- --- ---
--- --- --- --- --- --- ---
SAVE AND EXIT(ESC TO CANCEL)
--- : blank position
SCAN TYPE : NORMAL, VECTOR
DWELL : 03 ~ 99 SEC
003 : Preset (1 ~ 240)
A04 : Auto Scan (1 ~ 8, 10 ~ 17)
P01 : Pattern (1 ~ 8)
T02 : Tour (1 ~ 8)
Follow the steps below to program the Tours:
1. Press the P95P key to display the main menu on the monitor. Scroll to Tour and push the
Joystick to the right to enter the Tour menu. Or just press the P70P key on the keyboard.
2. Select “NUMBER” and set the desired number by pushing the Joystick to the left or right.
3. Choose a blank position to be programmed by pushing the Joystick up, down, right, or left.
4. To add a stored Preset, twist the Joystick; the stored Preset number displays.
5. To place functions other than preset, use the Joystick to move the cursor to a stored preset
position. Pressing the Open IRIS key will change the preset number to another function
(Auto Scan, Pattern, Tour or Preset) with the first programmed number. To change the
number, twist the Joystick or press the ZOOM in or ZOOM Out key.
6. You can also overwrite the programmed number and remove a stored number from the Tour.
Press the Open IRIS key on the stored number; a blank position mark (---) will be displayed.
7. Repeat step 2 through 6 for each desired position. Each title will be displayed on top of the line.
8. To edit the “TITLE”, follow the procedure of the Auto Scan, above, to edit titles.
9. Select “SAVE AND EXIT” and push the Joystick to the right or press the Open IRIS key.
Press the Close IRIS key to exit the program without saving.
You can expand the Tour sequence by calling other programmed Tours.
NOTE: The speed applies in Vector mode only.
NOTE: In Tour mode, in conjunction with Preset and Auto Scan, you can make the camera travel
from a Preset position to another Preset position at a specific speed.