Vicon VC-630 User manual

VC-630 AND VC-630C
COLOR BOX CAMERAS
About this manual
Dimensions : inches (mm)
INSTRUCTION MANUAL XX168-00
Before installing and using the camera, please read this manual
carefully. Be sure to keep it handy for later reference.
TROUBLESHOOTING
Before sending the camera out for repair, check the items
below. If the problem persists after checking these items,
contact your service center.
■If no image appears
Is the coaxial cable attached securely?
Are the power and voltage normal?
Has the iris of the lens inside the camera been
adjusted correctly (with the level volume) ?
Is there adequate illumination?
■If the image is unclear
Is the lens in focus?
Is the lens dirty?
Dirt or fingerprints on the lens can adversely affect the
images. Gently wipe any dirt or fingerprints off the lens
with a soft cloth or lens cleaning paper and cleaning
fluid (commercially available).
Is the monitor adjusted correctly?
WARNING:
TO PREVENT THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
SPECIFICATION
PRECAUTIONS
■Do not open or modify
Do not open the case except during maintenance and
installation, as it may be dangerous and cause damages.
■Do not put objects inside the unit
Make sure that no metal objects or flammable substances
get inside the camera. It could cause fire, short-circuits or
damages.
■Be careful when handling the unit
To prevent damage, do not drop the camera or subject
it to strong shock or vibration.
■Install away from electric or magnetic fields
■Protect from humidity and dust
■Protect from high temperature
Be careful when installing close to the ceiling , in a kitchen
or boiler room, as the temperature may rise to high levels.
■Cleaning
Dirt can be removed from the case only by wiping it
with a soft cloth moistened with a soft detergent solution.
■Mounting Surface
The mounting surface material must be strong enough to
secure the camera.
General NTSC PAL
CCD TYPE 1/3" 410K Pixels Color 1/3" 470K Pixels Color
Total Number of Pixels 811[H] x 508[V] 795[H] x 596[V]
Scanning System 525 Lines 625 Lines
Horizontal Resolution
Sensitivity to Light [30IRE]
Gamma Correction
Shutter Speed 1/60 - 1/100,000[NTSC] 1/50 - 1/100,000[PAL]
S/N Ratio
Synchronization
Video Output
White Balance
ME/AE
FLC
MIRROR
BLC
Operating Voltage
Consumption
Operating Temperature
Air Humidity
Connection via
Dimensions (W x H x D)
480TV Line
0.02fc, 0.2Lux(Scene) With F1.2 Lens
0.45
> 45dB
Internal / External
1.0Vp-p/75 ohm Composite
DIP Switch Select ME/AE (ON/OFF)
DIP Switch Select ON/OFF
BNC / Terminal block
2.2 x 2.0 x 4.7inch (57x51x120mm)
Mechanical Spec 14˚F - 131˚F (-10˚C - +55˚C)
Auto
Up to max. 85%
DC12V(DC11.0V~20.0), AC24V(20.0V~27.0V)
DC12V 1.65[W], AC24V 1.7[W]
DIP Switch Select ON/OFF
DIP Switch Select ON/OFF
Control DIP Switch
Electrical Spec

■CONNECTIONS
■CONNECTION OF LENS SOCKET "A-IRIS
"
■ADJUSTMENT OF BACK FOCU
S
■ ADJUSTMENT OF DC / AI LENS
CONNECTIONS AND CAMERA SETTINGS
Connect the coaxial cable (with pre-wired BNC plug) to the BNC connector (Video) of the camera.
If you are using an automatic iris lens with the camera, the lens has to be connected to the A-Iris socket of the camera. If
you are using a lens with manual or fixed iris, this socket is not used.
The operating voltage is either connected to the designated terminal block (12 V/DC or 24V/AC).
Operation of the camera will be confirmed by the power LED at the rear side of the camera.
Video Driven (AI)
1. +8.5 V DC
2. NC
3. Video signal
4. GND
DC Driven (DC)
1. Control –
2. Control +
3. Drive +
4. GND
To adjust a lens with automatic iris (DC driven or video driven) on the camera, please proceed as follows:
1. Turn the Level potentiometer (position: AI lenses on the lens itself, DC lenses: on the camera) to the max. position H
(turn right). The monitor picture then appears to be too bright.
2. Slowly turn the Level potentiometer back until the monitor picture appears to be perfect and is not too bright. Then
turn the potentiometer back to the right (in direction ”H”) just a little bit.
3. Check the lens performance by using the camera under different and/or changing light conditions.
ZOOM
FOCUS
COVER
1. Open the Front Cover.
2. Adjust the Angle of View and Focus.
3. Fix the position of adjustment lever after
adjusting preferred angle of view and focus.
4. Close the Front Cover.

■FOCUSING THE CAMERA LEN
S
■DESCRIPTION OF 4 PIN DIP SWITCH FUNCTIONS AND REAR PANEL CONNECTION
S
After you have selected the correct picture detail you have to adjust the lens focus.
The focus adjustment needs to be done with the iris fully open, since the camera has the smallest depth of focus in this
position. If the focus adjustment was not done with the iris completely open, the picture would appear to be sharp
during the day but slowly getting out of focus as the light disappears.
To fully open the lens, use a ND filter in front of the lens, provided you are using a lens with automatic iris.
Adjust the focus while the iris is fully open using the lens focus ring. Make sure the most important picture details are
in optimum focus (use a service monitor).
If it is not possible to bring the picture into focus, please adjust the back focus of the camera as described above.
If you intend to use I.R. illumination at a later stage, you must use an I.R. pass filter together with the ND filter during focus
adjustment to ensure that only I.R. light will get through to the camera chip and the focus adjustment is done according to this
spectrum, only.
Attention: I.R. light can only be used in combination with mono cameras, not color cameras!
1
2
3
4
5
6
7
1AE/ME
2FLIKER
3 MIRROR
4BLC
● Confirming the iris setting 1
●Adjusting level volume 5
CAUTION : Set to ON when DC LENS is installed. If the entire image is too dark or bright, or the backlight compensation is
ON The default setting when DC auto-iris lens is installed not correct even after 4 is set to "ON", you need to adjust the level volume.
(Low) Closes the lens iris, making the entire image darker
● Correcting Flicker 2
(High) Opens the lens iris, making the entire image brighter
Correct screen flickering athat occurs when positioned under
fluorescent lights that use a 50 Hz power supply frequency. ●Function 6
ON Under 50 Hz fluorescent lights
OFF Normal setting Terminal block for Power
● Setting Mirror Mode 3
ON Mirror Function is working (reverses image) ●Function 7
OFF Mirror Function is not working BNC Jack (Video)
● Compensating for backlight 4
ON When back light is too bright
OFF Normal setting

Brussels Office
Planet II - Unit E
Leuvensesteenweg 542
B-1930 Zaventem
Belgium
[phone]
Fax: [phone]
Far East Office
Unit 5, 17/F, Metropole Square
2 On Yiu Street, Shatin
New Territories,
Hong Kong
(852) 2145-7118
Fax: [phone]
Internet Address: www.vicon-cctv.com
Vicon Industries Inc.
Corporate Headquarters
89 Arkay Drive
Hauppauge, New York 11788
USA
631-952-CCTV (2288) 800-645-9116
Fax: 631-951-CCTV (2288)
European Headquarters
Brunel Way
Fareham, PO15 5TX
United Kingdom
[phone]
Fax: [phone]
Vicon Part number 8009-8168-00-00 Rev705