Vicon VC-600W User manual

VC-600W, VC-600WC
VC-610W, VC-610WC
VC-600WDN, VC-600WDNC
VC-600WIR, VC-600WIRC
COLOR DOME CAMERAS
About this manual
INSTRUCTION MANUAL XX173-00
Before installing and using the camera, please read this
manual carefully. Be sure to keep it handy for later reference.
This installation should be made by a qualified service
person and should conform to all local codes.
TROUBLESHOOTING
Before sending the camera out for repair, check the items
below.
If the problem persists after checking these items, contact
your service center.
■If no image appears
Is the coaxial cable attached securely?
Are the power and voltage normal?
Has the iris of the lens inside the camera been
adjusted correctly (with the level volume) ?
Is there adequate illumination?
■If the image is unclear
Is the lens in focus?
Is the lens dirty?
Dirt or fingerprints on the lens can adversely affect the
images. Gently wipe any dirt or fingerprints off the lens
with a soft cloth or lens cleaning paper and cleaning
fluid (commercially available).
Is the monitor adjusted correctly?
PRECAUTIONS
■Do not open or modify
Do not open the case except during maintenance and
installation, as it may be dangerous and cause damage.
■Do not put objects inside the unit
Make sure that no metal objects or flammable substances get
inside the camera. It could cause fire, short-circuits or damages.
■Be careful when handling the unit
To prevent damage, do not drop the camera or subject
it to strong shock or vibration.
■Install away from electric or magnetic fields
■Protect from humidity and dust
■Protect from high temperature
Be careful when installing close to the ceiling, in a kitchen or boiler
room, as the temperature may rise to high levels.
■Cleaning
Dirt can be removed from the case only by wiping it
with a soft cloth moistened with a soft detergent solution.
■Mounting Surface
The mounting surface material must be strong enough to
support the camera.
CAMERA DIMENSIONS in. (mm)

SPECIFICATION VC-600WDN/C SPECIFICATION VC-600WIR/C
SPECIFICATION VC-610W/CSPECIFICATION VC-600W/C
GENERAL Spec NTSC PAL
HQ Interline Transfer CCD 1/3" 410K Pixels Color 1/3" 470K Pixels Color
Total Number of Pixels 811(H) x 508(V) 795(H) x 596(V)
Scanning System 525 Lines 625 Lines
Horizontal Resolution
Sensitivity to Light [30IRE]
Gamma Correction
Shutter Speed 1/60 - 1/100,000[NTSC] 1/50 - 1/100,000[PAL]
S/N Ratio
Synchronization
Video Output
Control DIP Switch
BLC DIP Switch Select ON/OFF
ME/AE DIP Switch Select ME/AE (ON/OFF)
ATW/AWB DIP Switch Select ATW/AWB (ON/OFF)
AGC DIP Switch Select ON/OFF
Electrical Spec
Operating Voltage 12VDC(11-20V), 24VAC(20-27V)
Power Consumption 12VDC - 2.5[W], 24VAC - 2.0[W]
Mechanical Spec
Opertion Temp 14°F ~ 131°F (-10°C ~ +55°C)
Air Humidity Up to max.90%
Lens Mount 3.3~12mm
Connections via BNC(VIDEO), 2P WIRE(POWER)
0.45
0.3Lux(Scene) With F1.2 Lens
550TV Lines
10Vp-p/75ohm Composite
Internal / External (Line Lock)
> 48dB [AGC off]
GENERAL Spec NTSC PAL
HQ Interline Transfer CCD 1/3" 410K Pixels Color 1/3" 470K Pixels Color
Total Number of Pixels 811(H) x 508(V) 795(H) x 596(V)
Scanning System 525 Lines 625 Lines
Horizontal Resolution
Sensitivity to Light [30IRE]
Gamma Correction
Shutter Speed 1/60 - 1/100,000[NTSC] 1/50 - 1/100,000[PAL]
S/N Ratio
Synchronization
Video Output
Control DIP Switch
BLC DIP Switch Select ON/OFF
ME/AE DIP Switch Select ME/AE (ON/OFF)
ATW/AWB DIP Switch Select ATW/AWB (ON/OFF)
AGC DIP Switch Select ON/OFF
Electrical Spec
Operating Voltage 12VDC(11-20V), 24VAC(20-27V)
Power Consumption 12VDC - 2.5[W], 24VAC - 2.0[W]
Mechanical Spec
Opertion Temp 14°F ~ 131°F (-10°C ~ +55°C)
Air Humidity Up to max.90%
Lens Mount 3.3~12mm
Connections via BNC(VIDEO), 2P WIRE(POWER)
0.45
(BW) 0.04Lux(Scene) With F1.2 Lens
550TV Lines
10Vp-p/75ohm Composite
Internal / External (Line Lock)
> 48dB [AGC off]
GENERAL Spec NTSC PAL
CCD Type 1/3" 410K Pixels Color 1/3" 470K Pixels Color
Total Number of Pixels 811(H) x 508(V) 795(H) x 596(V)
Scanning System 525 Lines 625 Lines
Horizontal Resolution
Sensitivity to Light [30IRE]
Gamma Correction
Shutter Speed 1/60 - 1/100,000[NTSC] 1/50 - 1/100,000[PAL]
S/N Ratio
Synchronization
Video Output
White Balance
WDR
Control DIP Switch
ME/AE DIP Switch Select ME/AE (ON/OFF)
ATW/AWB DIP Switch Select ATW/AWB (ON/OFF)
WDR ON/OFF DIP Switch Select WDR (ON/OFF)
AGC MAX ON DIP Switch Select ON/OFF
Electrical Spec
Operating Voltage 12VDC(10-20V), 24VAC(20-27V)
Power Consumption 12VDC - 3.0[W], 24VAC - 2.5[W]
Mechanical Spec
Opertion Temp 14°F ~ 131°F (-10°C ~ +55°C)
Air Humidity Up to max.90%
Lens Mount 3.3~12mm
Connections via BNC(VIDEO), 2P WIRE(POWER)
Auto
ON or OFF (DIP S/W)
0.45
0.06fc, 0.6Lux(Scene) With F1.2 Lens
550TV Lines
10Vp-p/75ohm Composite
Internal / External (Line Lock)
> 45dB [AGC off]
GENERAL Spec NTSC PAL
CCD Type 1/3" 410K Pixels Color 1/3" 470K Pixels Color
Total Number of Pixels 811(H) x 508(V) 795(H) x 596(V)
Scanning System 525 Lines 625 Lines
Horizontal Resolution
Sensitivity to Light [30IRE]
Gamma Correction
Shutter Speed 1/60 - 1/100,000[NTSC] 1/50 - 1/100,000[PAL]
S/N Ratio
Synchronization
Video Output
Control DIP Switch
BLC DIP Switch Select ON/OFF
ME/AE DIP Switch Select ME/AE (ON/OFF)
ATW/AWB DIP Switch Select ATW/AWB (ON/OFF)
AGC DIP Switch Select ON/OFF
Electrical Spec
Operating Voltage 12VDC(11-20V), 24VAC(20-27V)
Power Consumption MAX LED OFF (12VDC - 2.5[W], 24VAC - 1.92[W])
MAX LED ON (12VDC - 4.44[W], 24VAC - 4.7[W])
Mechanical Spec
Opertion Temp 14°F ~ 131°F (-10°C ~ +55°C)
Air Humidity Up to max.90%
Lens Mount Fixed board lens (M12 mount)
Connections via BNC(VIDEO), 2P WIRE(POWER)
0.45
(B/W, No LED) 0.04Lux(Scene) With F1.2 Lens
550TV Lines
10Vp-p/75ohm Composite
Internal / External (Line Lock)
> 48dB [AGC off]

■LENS ADJUSTMEN
T
VC-600W, VC-610W, VC-600WDN VC-600WIR
■CONNECTION
■VC-600W, VC-600WC
CAMERA SETTINGS
LENS ADJUSTMENT AND CONNECTION
1. Adjust the panning (360˚) and tilt (51˚) position.
2. Set the zoom position by using Zoom Lever Screw.
3. Set the focus by using Focus Lever Screw.
4. Loosen set screws to adjust roll
(turns camera position top/bottom).
12VDC
Red (+)
Black (-)
24VAC
CAUTION
Check for polarity when using a 12VDC power supply.
1. Adjust the panning (360˚) and tilt (60˚) position.
2. Set the zoom position by using Zoom Lever Screw.
3. Set the focus by using Focus Lever Screw.
4. Loosen set screws to adjust roll
(turns camera position top/bottom).
PAN - 360˚
TILT - 60˚
Zoom
Focus
Set Screw
(2x)
°
TILT - 51˚
PAN - 360˚
NO. FUNCTION
1BLCOFFON
2 AE/ME AE ME
3 ATW/AWB AWB ATW
4 AGC MAX OFF ON
DIP S/W
●Compensating for backlight 1
ON When backlight is too bright
OFF Normal setting
CAUTION : It will be correctly set by adjusting level volume 5.
●Confirming the iris setting 2
ON When DC autoiris lens installed
OFF when fixed iris lens is installed
●White balance setting 3
Use this under light source below 2500K and over
9500K of Natrium(Sodium) low color temperature light
Use this under light source between 2500K and
9500K of fluorescent lamp, incandescent light.
ATW (ON)
AWB (OFF)

■VC-610W, VC-610WC
■VC-600WDN/C, VC-600WIR/C
●Confiming the wide dynamic range setting 3
WDR(ON) WDR is working
WDR(OFF) WDR is not working
●Setting gain control (AGC) 4
For adjusting the sensitivity of the camera.
Use this setting for shooting in dark environments.
ON Normal Setting
OFF Set this when there is excessive noise
●Setting gain control (AGC) 4
For adjusting the sensitivity of the camera.
Use this setting for shooting in dark environments.
ON Normal Setting
OFF Set this when there is excessive noise.
●Adjusting level volume 5
If the entire image is too dark or bright, or the backlight
compensation is not correct, you need to adjust the level volume.
CCW (LOW) Closes the lens iris, making the entire image darker
CW (HIGH) Opens the lens iris, making the entire image brighter.
①
Portable
Monitor
②
③④
⑤
⑥
DC VARIFOCAL
⑦
●Confirming the iris setting 1
DC IRIS (ON) When DC autoiris lens installed
EE (OFF) when fixed iris lens is installed
●Whitel balance setting 2
Use this under light source below 2500K and
over 9500K of Natrium light
Use this under light source between 2500K and
9500K of fluorescent lamp, incandescent light.
ATW (ON)
AWB (OFF)
ON
OFF
12 34

INSTALLATION - VC-600W/C, VC-610W/C, VC-600WDN/C
1 Use the supplied hexagon wrench to remove the four
fixing screws (B) of dome cover (A).
2 Make screw holes and a cable hole in the supplied
cushioning sheet (D) that attaches to the back of the
camera unit (C) .
3 Attach the cushioning sheet (single-sided tape) to the
back of the camera unit.
4 Align the camera unit with the surface of the ceiling,
make marks on the ceiling in the places where the
screw holes are to be drilled, and then drill the four holes.
5 Cut a hole (diameter: 2.9 in / 73mm) in the ceiling for
routing the cables.
6 Pass the power cable (E) and video cable (F) from the
camera unit through the cable hole in the ceiling.
7 Align the four screw holes in the camera unit (C) with
the screw holes in the ceiling, and then secure the
camera in place by tightening the four or more screws
(G) throught the washers.
8 Carry out the settings and adjustments for the camera.
9 If the dome liner (H) is secured in place, loosen the
screw (I). Adjust the dome liner (H) so that the dome
camera's lens is visible from the camera window,
and then use a philips screwdriver to fix the dome cover.
10 Secure the dome cover (A) by tightening the screws (B).
A
B
C
D
EF
G
H
I
①DIP Switch Functions
(1) Compensating for backlight (2) Confirming the iris setting
ON When backlight is too bright AE (OFF) When fixed iris lens is installed
OFF Normal setting ME (ON) When DC autoiris lens is installed
CAUTION : It will be correctly set by adjusting DC lens control. CAUTION : The iris setting is preadjusted as the best condition for
use at time of factory shipment, so it isn't necessary to change settings
(3) Confirming the white balance (4) Setting gain control (AGC)
For adjusting the sensitivity of the camera. Use this setting for shooting
in dark environments.
ON Normal setting
OFF Set this when there is excessive noise
②Second Video OUT Connector (Option) ⑤Adjusting Level Volume
If installer is setting with portable monitor, this connector is If the entire image is too dark or bright, or the backlight
used. compensation is not correct even after ①is set to "ON",
③IR LED Connector (Option)
you need to adjust the level volume.
If extra IR LED board is attached, this connector is used.
CCW (Low) Closes the lens iris, making the entire image darker
④Setting Monitor Synchronization
CW (High) Opens the lens iris, making the entire image brighter
(24VAC adaptor users)
⑥DC Varifocal Connector
Vertical sync disturbance may occur when a selector is used to This should be used with ⑤DC IRIS LENS.
switch between multiple cameras connected to one monitor. ⑦Power Connector
To prevent vertical sync disturbance, adjust ④.Connect with AC/DC power, board attached inside.
CAUTION
* When using the 12VDC adaptor, sync setting is set to internal sync.
ATW(ON) Use this under light source below 2500K and over 9500K of
natrium.
AWB(OFF) Use this under light source between 2500K and 9500K of
fluorescent lamps, incandescent light

INSTALLATION - VC-600WIR/C
1 Use the supplied hexagon wrench to remove the four fixing screws (B) of dome cover (A).
2 Make screw holes and a cable hole in the supplied cushioning sheet (D) that attaches to the back of the
camera unit (C) .
3 Attach the cushioning sheet (single-sided tape)(D) to the back of the camera unit.(C).
4 Align the camera unit with the surface of the ceiling, make marks on the ceiling in the places where the
screw holes are to be drilled, and then drill the four holes.
5 Cut a hole (diameter: 2.9 in. / 73mm) in the ceiling for routing the cables.
6 Pass the power cable (E) and video cable (F) from the camera unit through the cable hole in the ceiling.
7 Align the four screw holes in the camera unit (C) with the screw holes in the ceiling, and then secure the
camera in place by tightening the four or more screws (G) throught the washers.
8 Carry out the settings and adjustments for the camera.
9 If the dome liner (H) is secured in place, loosen the screw (I). Adjust the dome liner (H) so that the dome camera's
lens is visible from the camera window, and then use a philips screwdriver to fix the dome cover.
10 Secure the dome cover (A) by tightening the screws (B).
C
IH
A
B
D
E
G
F

Brussels Office
Planet II - Unit E
Leuvensesteenweg 542
B-1930 Zaventem
Belgium
[phone]
Fax: [phone]
Far East Office
Unit 5, 17/F, Metropole Square
2 On Yiu Street, Shatin
New Territories,
Hong Kong
(852) 2145-7118
Fax: [phone]
Internet Address: www.vicon-cctv.com
Vicon Industries Inc.
Corporate Headquarters
89 Arkay Drive
Hauppauge, New York 11788
USA
631-952-CCTV (2288) 800-645-9116
Fax: 631-951-CCTV (2288)
European Headquarters
Brunel Way
Fareham, PO15 5TX
United Kingdom
+ 44(0) 1489 566300
Fax: + 44(0) 1489 566322
VICON PART NO. 8009-8173-00-00, rev 106