Vicon XX247-10-01 User manual

www.vicon-security.com
XX247-10-01
V-CELL-HD High-Security
Corner-Mount Cameras
Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet your requirements or that the
operation will be entirely error free or perform precisely as described in the documentation. This system has not been designed
to be used in life-critical situations and must not be used for this purpose.
Vicon Industries Inc.
Tel: [phone] Fax: [phone] Toll Free: 800-645-9116
24-Hour Technical Support: 800-34-VICON (800-348-4266) UK: 44/(0) 1489-566300
Document Number: 8009-8247-10-01
Product specications subject to change without notice.
Issued: 814
Copyright © 2014 Vicon Industries Inc. All rights reserved.
User Guide

2
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE. DO NOT INSERTANY METALLIC OBJECT THROUGH THE VENTILATION
GRILLS OR OTHER OPENINGS ON THE EQUIPMENT.
CAUTION
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user
to the presence of uninsulated "dangerous voltage" within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature accompanying the
appliance.
PRECAUTIONS
Safety -------------------------------------- Installation -------------------------------
Should any liquid or solid object fall into the cabinet,
unplug the unit and have it checked by the qualified
personnel before operating it any further.
Unplug the unit from the wall outlet if it is not going to
be used for several days or more. To disconnect the
cord, pull it out by the plug. Never pull the cord itself.
Allow adequate air circulation to prevent internal heat
build-up. Do not place the unit on surfaces (rugs,
blankets, etc.) or near materials(curtains, draperies)
that may block the ventilation holes.
Height and vertical linearity controls located at the rear
panel are for special adjustments by qualified
personnel only.
Do not install the unit in an extremely hot or humid
place or in a place subject to excessive dust,
mechanical vibration.
The unit is not designed to be waterproof.
Exposure to rain or water may damage the unit.
Cleaning ---------------------------------
Clean the unit with a slightly damp soft cloth.
Use a mild household detergent. Never use strong
solvents such as thinner or benzene as they might
damage the finish of the unit.
Retain the original carton and packing materials for
safe transport of this unit in the future.

3
FCC COMPLIANCE STATEMENT
INFORMATION TO THE USER:THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO
COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC
RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL
INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT. THIS
EQUIPMENT GENERATES, USES, AND CAN RADIATE RADIO FREQUENCY ENERGY AND IF NOT
INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL
INTERFERENCE TO RADIO COMMUNICATIONS.
CAUTION:CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY
RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER'S AUTHORITY TO OPERATE THE
EQUIPMENT.
THIS CLASS A DIGITALAPPARATUS COMPLIES WITH CANADIAN ICES-003.
CET APPAREIL NUMÉRIQUE DE LA CLASSE A EST CONFORME À LA NORME NMB-003 DU CANADA.
CE COMPLIANCE STATEMENT
WARNING: This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.

4
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. Apolarized plug has
two blades with one wider than the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury
from tip-over.
13. Unplug this apparatus during lightning storms or when unused for
long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, such as
power-supply cord or plug is damaged, liquid has been moisture,
does not operate normally, or has been dropped.
15. CAUTION – THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALIFIED
SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF ELECTRIC SHOCK DO
NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE
OPERATING INSTRUCTIONS UNLESS YOU QRE QUALIFIED TO DO SO.
16. Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class 2
power source only.
17. ITE is to be connected only to PoE networks without routing to the outside plant.

5
Contents
1. Description ------------------------------------------------------------------6
1.1 Components - ------------------------------------------------------------------------------------------ 6
1.2 Key Features- ------------------------------------------------------------------------------------------ 7
2. Installation ------------------------------------------------------------------- 8
2.1 Overview--------------- ------------------------------------------------------------------------------------8
2.3 Unpacking and Inspection -----------------------------------------------------------------------------11
2.4 Physical Installation -------------------------------------------------------------------------------------11
2.5 Network Connection and IP Assignment ---------------------------------------------------------- 15
3. Operation -------------------------------------------------------------------- 16
3.1 Access from a browser -------------------------------------------------------------------------------- 16
3.2 Access from the internet------------------------------------------------------------------------------ 17
3.3 Setting the admin password over a secure connection------------------------------------------- 17
3.4 Live View Page ----------------------------------------------------------------------------------------- 18
3.5 Network camera Setup -------------------------------------------------------------------------------- 20
3.5.1 Basic Configuration ---------------------------------------------------------------------------- 20
1) Users------------------------------------------------------------------------------------------ 21
2) Network -------------------------------------------------------------------------------------- 22
3) Video & Image ------------------------------------------------------------------------------ 23
4) Audio------------------------------------------------------------------------------------------ 25
5) Date & Time --------------------------------------------------------------------------------- 27
3.5.2 Live View ----------------------------------------------------------------------------------------- 28
3.5.3 Video & Image---------------------------------------------------------------------------------- 29
3.5.4 Audio---------------------------------------------------------------------------------------------- 35
3.5.5 Event---------------------------------------------------------------------------------------------- 36
1) Event-In -------------------------------------------------------------------------------------- 36
2) Event-Out ------------------------------------------------------------------------------------ 42
3) Event Map------------------------------------------------------------------------------------ 49
3.5.6 Device ----------------------------------------------------------------------------------------- 51
3.5.7 System ------------------------------------------------------------------------------------------ 52
1) Information ---------------------------------------------------------------------------------- 52
2) Security--------------------------------------------------------------------------------------- 53
3) Date & Time --------------------------------------------------------------------------------- 58
4) Network -------------------------------------------------------------------------------------- 59
5) Language------------------------------------------------------------------------------------- 69
6) Maintenance --------------------------------------------------------------------------------- 70
7) Support--------------------------------------------------------------------------------------- 71
3.5.8 about ------------------------------------------------------------------------------------------ 74
3.6 Playback--------------------------------------------------------------------------------------------------- 75
3.7 Help-------------------------------------------------------------------------------------------------------- 77
3.8 Resetting to the factory default settings ------------------------------------------------------------- 78
4. Appendix -------------------------------------------------------------------- 79
4.1 Troubleshooting ----------------------------------------------------------------------------------------- 79
4.2 Alarm Connection---------------------------------------------------------------------------------------- 80
4.3 Preventive Maintenance -------------------------------------------------------------------------------- 80
4.4 Product Specification ----------------------------------------------------------------------------------- 81

6
1. Description
The information in this manual provides quick installation and setup procedures for the V-CELL-HD of
High-Security Corner-Mounted Cameras. These units should only be installed by a qualified technician
using approved materials in conformance with federal, state, and local codes. Read these instructions
thoroughly before beginning an installation. Refer to the complete manual for detailed information.
Always refer to Vicon’s website to assure you have the most up-to-date manual, http://www.vicon-
security.com.
The Roughneck® V-CELL-HD high-security camera is an integrated housing, camera, lens and IR
illuminators system specifically designed for use in custodial suites and prison cells. It is available in
an IP version that is fully compatible with all ViconNet® systems; its ONVIF certification provides an
open-platform for integration into other video management systems.
The housing is designed to fit into a corner; once installed, the base plate should be permanently
sealed to the wall so that the housing is ligature proof. The housing consists of a two part stainless
steel assembly, a fixed base plate and a removable front plate, that allows ease of installation and
servicing. The front plate is secured with security screws and has two polycarbonate windows to
protect the camera and IR illuminators. The alarm input and alarm output can be used to connect
various third party devices, such as door sensors and alarm bells.
1.1 Components
The system comes with the following components:
Cameraunit InstallationGuide InstallationCD AccessoryKit
OptionalOSDController
Check your package to make sure that you received the complete system, including all components
shown above.
Note: The optional OSD Controller can be purchased separately.

7
1.2 Key Features
• Brilliant video quality
The network camera offers the highly efficient H.264 video compression, which drastically
reduces bandwidth and storage requirements without compromising image quality. Motion JPEG
is also supported for increased flexibility.
• Triple streams
The network camera can deliver triple video streams simultaneously at full frame rate in all
resolutions up to Full HD (1920x1080) using Motion JPEG and H.264 (or MPEG-4). This means
that several video streams can be configured with different compression formats, resolutions and
frame rates for different needs.
• Image setting adjustment
The network camera also enables users to adjust image settings such as contrast, brightness and
saturation to improve images before encoding takes place.
• Intelligent video capabilities
The network camera includes intelligent capabilities such as enhanced video motion detection.
The camera’s external inputs and outputs can be connected to devices such as sensors and relays,
enabling the system to react to alarms and activate lights or open/close doors.
• Micro-SD recording support
The network camera also supports a micro-SD memory slot for local recording with removable
storage.
• Improved security
The network camera logs all user access, and lists currently connected users. Also, its full frame
rate video can be provided over HTTPS.
• IR illumination
36 IR LED illuminators (940nm with low visibility) light up to 66 ft (20m); intensity; adjustable.
• Audio In/Out
1 Mic/1 Speaker (G.711)
• Power over Ethernet
Support for Power over Ethernet (IEEE802.3af) enables the unit, as well as the camera module
that is connected to it, to receive power through the same cable as for data transmission. This
makes for easy installation since no power outlet is needed.
• ONVIF
This is a global interface standard that makes it easier for end users, integrators, consultants,
and manufacturers to take advantage of the possibilities offered by network video technology.
ONVIF enables interoperability between different vendor products, increased flexibility, reduced
cost, and future-proof systems.

8
2. Installation
For the network camera to operate, it is necessary to connect a network cable for data transmission
and power connection from customer-supplied power supply.
2.1 Overview
Parts and Description
①Main Power 24VAC/12VDC (↑(+) pole /↓(-) pole)
②RJ45(PoE) Port
③Micro-SD Card Slot
④Alarm & Audio In/Out Port
⑤Status LED
Upon boot-up, green and red are both on for a short time and then only green will be on.
If red is lit, this indicates a failure (no picture); if flashing green and no red,
this indicates a good picture is displaying.
⑥Service Monitor Port

9
Quick Installation
Below is an overview for installing the V-CELL-HD camera. When using
1) Installation (without Rear Cover)
1. Use camera mounting frame as template to mark mounting holes on mounting surface. (Fig.1)
2. Drill holes for mounting base and a minimum 3/4 in. hole for routing wines. (Fig.1)
3. Mount camera mounting frame using appropriate hardware for mounting surface. (Fig.2)
4. Route wires through hole in wall and out through base plate. (Fig.2).
5. Terminate wires to camera board.
6. Mount front plate to base plate. (Fig.2)

10
2) Installation (using Rear Cover)
1. Use rear cover as template to mark mounting and cable access holes.
2. Drill mounting and cable access holes in mounting surface.
3. Insert cable clamp into access hole, route cables through clamp and mount cover using
appropriate hardware.
4. Use camera mounting frame to mark its mounting holes, drill holes and mount using
appropriate hardware.
5. Terminate wires to camera board. Feed the excess wire back through cable clamp and tighten
clamp.
6. Mount front plate to camera mounting frame.
Note: Installation of the rear cover is required for UL/Canadian UL compliance.

11
2.2 Unpacking and Inspection
All Vicon equipment is inspected and tested before leaving the factory. It is the carrier’s responsibility
to deliver the equipment in the same condition in which it left the factory.
Inspection for Visible Damage
Immediately inspect the cartons upon delivery. On all copies of the carrier’s freight bill, make a note
of any visible damage.
Make sure the carrier’s agent (the person making the delivery) signs the note on all copies of the bill.
If the agent does not have claim forms, contact the carrier’s office.
Inspection for Concealed Damage
As soon as possible after delivery, unpack the unit and inspect it for concealed damage. Do not
discard the carton or packing materials. If the unit is damaged, contact the carrier immediately and
request forms for filing a damage claim. Make arrangements for a representative of the carrier to
inspect the damaged equipment.
If the equipment must be returned for repair, follow the Shipping Instructions at the end of this
document.
2.3 Physical Installation
The V-CELL-HD is designed to fit into a corner where two walls and a ceiling meet. It is fastened to
both walls and the ceiling. Refer to Figure 1. Cable access is provided by removing the front plate.
The camera has an adjustable mount that may be tilted slightly to give a precise angle of view. A 2.5
mm wide angle lens enables the camera to view the cell with no “blind spots;” 36 IR LED illuminators
are provided to light up to 66 ft (20 m).
The wall/ceiling material must provide suitable strength to support the weight of the unit (3.5 lb/1.6
kg). Be sure the area around the selected location is clear of obstacles (such as steel beams, headers,
pipes, electrical wiring, etc.) that would interfere with mounting. All cables must be routed to the
installation location. Before beginning installation, read the Cable Recommendations at the end of this
manual and verify that the accessory pack contains the items listed in below table.
Item Quantity Function
No. 20 Torx Bit 1 Use to remove and install tamperproof
screws from front plate
No. 20 Torx Bit 1 Use to remove and install tamperproof
screws from front plate access cover plate
2-Pin Terminal Block 1 Use to make power cable connections
Back Cover 1 Fire barrier; required for UL/cUL compliance
Quick Guide/Documentation
CD/ ViconNet CD (IP versions) 1 Installation and operation instructions;
ViconNet setup CD

12
Mounting the Housing
The housing consists of two main assemblies, the camera mounting frame and the removable
front plate, where the camera and all electronics are mounted. The front plate is secured to the
base plate with Resistorx tamperproof screws. A special bit is supplied in the accessory pack for
removing and replacing these screws. When the installation is complete, retain the Torx bit in
case access to the interior of the housing is required later. Additionally, a rear cover is supplied
for those installations requiring Canadian UL compliance or extra protection from fire.
1) Installation without the rear cover:
1. Remove the front plate using the no. 20 Torx bit provided; retain the screws in a safe place.
Using the camera mounting frame as a template, mark the locations of the mounting holes on
the three mounting tabs (2 holes per tab). Open a hole in the wall or ceiling to accommodate
routing the cables to the camera.
2. Route all necessary cables to the location if not already done so.
3. Drill suitable holes for the hardware selected appropriate for the wall/ceiling material. The use
of No. 8 (or 4 mm metric) mounting hardware is recommended. Use hollow-wall anchors or, if
the housing is being mounted on a sheet metal surface, use rivet nuts.
4. Secure the camera mounting frame to the wall/ceiling with fasteners appropriate for the
mounting surface. Route the cables through the access hole in the wall or ceiling.
5. When the camera mounting frame is secured to the surface, apply an epoxy security sealant
around the perimeter of the base plate where it meets the ceiling/wall. [Vicon recommends
DynaPoxy™ EP1200 (US) or Arbokol 1025 (UK) or equivalent for this purpose.]
2) Installation with the rear cover:
Note: The installation corner must be sharp and clean; if necessary, clean any excess material
from the installation location.
1. Remove the front plate using the no. 20 Torx bit provided; retain the screws in a safe place.
2. Select the cable access hole in the rear cover to be used (6 provided) and knockout the hole.
Place the rear cover in the corner; using it as a template, mark the locations of the three (3)
mounting holes and the cable access hole. Remove it from the corner.
3. Drill suitable mounting holes and open the hole to accommodate routing the cables to the
camera in the wall/ceiling. Be sure the cable access hole is large enough to accommodate the
cable clamp.
4. Route all necessary cables to the location if not already done so. Fasten the cable clamp
(provided) into the cable access knockout hole so that the clamp is on the inside of the rear
cover. Route cables through the access hole and through the rear cover; be sure to allow
enough cable length to make connections to the camera board. Mount the rear cover to the
wall/ceiling through the 3 holes provided; use hardware appropriate for the mounting surface.
5. Using the camera mounting frame as a template, insert it into the rear cover and mark the
mounting holes on the 3 tabs (2 holes per tab) that align with the holes in the rear cover; drill
suitable mounting holes. Attach the camera mounting frame onto the wall/ceiling and secure it
using appropriate hardware for the mounting surface. The use of No. 8 (or 4 mm metric)
mounting hardware is recommended. Use hollow wall anchors or, if the housing is being
mounted on a sheet metal surface, use rivet nuts.
6. Make cable connections to the camera board. See instructions below. Adjust the cable length

13
as necessary and secure the cable clamp.
Caution: Installation of the rear cover is required for UL/Canadian UL compliance.
7. When the camera mounting frame assembly is secured to the surface, apply an epoxy security
sealant around the perimeter of the base plate assembly where it meets the ceiling/wall. [Vicon
recommends DynaPoxy™ EP1200 (US) or Arbokol 1025 (UK) or equivalent for this purpose.]
Cable Connections
All cabling is done to the boards located on the back of the front plate.
Note: Vicon systems and components, like most electronic equipment, require a clean, stable
power source. Voltage irregularities such as surges, drops, and interruptions can affect the
operation of your equipment and, in severe cases, damage certain components.
1) Micro SD memory slot on the Board
Card Slot for Micro SD memory: Socket “J10.” (SD card customer-supplied.)
2) Connecting to the RJ-45
Connect a standard RJ-45 cable to the network port of the network camera. Generally a
crossover cable is used for direct connection to a PC, while a direct cable is used for
connection to a hub.
3) Connecting Alarms
AI (Alarm In):
External devices can be used to signal the network camera to react upon events. Mechanical
or electrical switches can be wired to the AI (Alarm In) and G (Ground) connectors.
G (Ground):
Connect the ground side of the alarm input and/or alarm output to the G (Ground) connector.
Alarm Out:
The network camera can activate external devices such as buzzers or lights. Connect the
device to the AO (Alarm Out) and G (Ground) connectors.
4) Connecting the Power
Connect the power of 12 VDC or 24 VAC for the network camera. Connect the positive (+) pole to
the ‘+’ position and the negative (-) pole to the ‘-’ position for the DC power.
Be careful not to reverse the polarity when connecting the power cable.
A router featuring PoE (Power over Ethernet) can also be used to supply power to the
camera.
The heater can be powered by a 24VAC, 12VDC, or PoE power source.
For the power specifications, refer to the Appendix, Product Specification.
If PoE and 12 VDC are both applied, the camera will be supplied with power from PoE.
5) IR Control
To adjust the intensity of the IR illuminators, use the Day & Night menu in the web browser.

14
6) Connecting Service Monitor Port
The Service Monitor output port (J1) is located on the front board of the camera and is used for
easy OSD setup.
▶ID & IP assignment
To make changes in the OSD menu, the optional OSD controller can be used to set the
camera title and IP address.
1. Connect the OSD Controller to the Service Monitor port of the network camera.
2. Connect Service Monitor and the Video Output port of the OSD Controller.
3. Press the SET button on the controller to access the Main Menu.
4. Change camera ID and IP address as needed. Additionally, the Name (or title) of the
camera can be changed. Use the ↑↓←→ buttons on the controller to change the
parameters.
5. Select SAVE or CANCEL to exit the Main Menu.
The Video Output can also be used for easy zoom and focus control when adjusting the lens.
Video Output is restricted to 704x480 (576) resolution.
Note: The optional OSD Controller can be purchased separately.
Final Installation

15
When all connections are made, secure the front plate to the base plate using the security screws
previously removed using no. 20 Torx bit.
2.4 Network Connection and IP assignment
The network camera is designed for use on an Ethernet network and requires an IP address for access.
Most networks today have a DHCP server that automatically assigns IP addresses to connected
devices. By factory default, your camera is set to obtain the IP address automatically via DHCP server.
If your network does not have a DHCP server the network camera will use 192.168.1.100 as the
default IP address.
If DHCP is enabled and the product cannot be accessed, run the “Smart Manager” utility on the CD to
search and allocate an IP address to your product or reset the product to the factory default settings
and then perform the installation again.
1. Connect the network camera/device to the network and power up.
2. Start SmartManager utility (Start>All programs>SmartManager>SmartManager); the main
window will display. After a short while any network devices connected to the network will be
displayed in the list.
3. Select the camera on the list and click right button of the mouse. The pop-up menu displays as
below.
4. Select Assign IP. The Assign IP window displays. Enter the required IP address.

16
Note: For more information, refer to the Smart Manger User’s
Manual.
3. Operation
The network camera can be used with Windows® operating system and browsers. The recommended
browsers are Internet Explorer®, Safari®, Firefox®, Opera® and Google® Chrome® with Windows.
Note:To view streaming video in Microsoft® Internet Explorer, set your browser to allow ActiveX
controls.
3.1 Access from a browser
1. Start a browser (i.e., Internet Explorer).
2. Enter the IP address or host name of the network camera in the Location/Address field of your
browser.
3. A starting page displays. Click Live View or Setup to enter web page.
4. Click Live View for the network camera’s Live View page to appear in the browser.

17
3.2. Access from the internet
Once connected, the network camera is accessible on your local network (LAN). To access the
network camera from the Internet you must configure your broadband router to allow incoming data
traffic to the network camera. To do this, enable the NAT-traversal feature, which will attempt to
automatically configure the router to allow access to the network camera. This is enabled from Setup
> System > Network > NAT.
For more information, see “3.5.7 System>Network>NAT” of this User’s Manual.
3.3 Setting the admin password over a secure connection
To gain access to the product, the password for the default administrator user must be set. This is
done in the “Admin Password” dialog, which is displayed when the network camera is accessed for the
setup at the first time. Enter your admin name and password, set by the administrator.
Note: The default administrator username is ADMIN and password is 1234. If the password is lost,
the network camera must be reset to the factory default settings. See “3.8 Resetting to the Factory
Default Settings” for more details.
To prevent network eavesdropping when setting the admin password, use an encrypted HTTPS
connection, which requires an HTTPS certificate (see note below).
To set the password via a standard HTTP connection, enter it directly in the first dialog shown below.
To set the password via an encrypted HTTPS connection, see “3.5.7 System >Security>HTTPS”.
Note: HTTPS (Hypertext Transfer Protocol over SSL) is a protocol used to encrypt the traffic between
web browsers and servers. The HTTPS certificate controls the encrypted exchange of information.

18
3.4 Live View Page
T
he Live View pa
g
e provides several screen
modes: 1920x1080, 1280x1024, 1280x720,
704x480 (576), 640x480, 352x240 (288)
and 320x240. Select the most suitable in
accordance with your PC specifications and
monitorin
g
purposes.
1) General controls
LiveViewPage Search&PlaybackPage SetupPage HelpPage
The video drop-down list allows you to select a customized or pre-programmed
video stream on the live view page. Stream profiles are configured under Setup > Basic
Configuration > Video & Image. For more information, see “3.5.1 Basic Configuration > Video &
Image” of User’s Manual
The resolution drop-down list allows you to select the most suitable video
resolution to be displayed on live view page.
Theprotocoldrop-downlistallowstheselectionofthecombinationof
protocols and methods to use depending on your viewing requirements and on the properties of
the network.
2) Control toolbar
The live viewer toolbar is available in the web browser page only. It displays the following
buttons:
The Stop button stops the video stream being played. Pressing the key again toggles the
start and stop. The Start button connects to the network camera or starts playing a
video stream.
The Pause button temporarily stops (pauses) the video stream being played.
The Snapshot button takes a takes a picture (snapshot) of the current image. The location
where the image is saved can be specified.
The digital zoom activates a zoom-in or zoom-out function for video image on the live
screen.
The Full Screen button causes the video image to fill the entire screen area. No other
windows will be visible. Press the 'Esc' button on the computer keyboard to cancel full
screen view.
The Manual Trigger button activates a pop-up window to manually start or stop the event.
Use the Speaker icon scale to control the volume of the speakers.
Use the Microphone icon scale to control the volume of the microphone.

19
3) Video Streams
The network camera provides several images and video stream formats. Your requirements and
the properties of your network will determine the type you use.
The Live View page in network camera provides access to H.264, MPEG-4 and Motion JPEG video
streams and to the list of available video streams. Other applications and clients can also access
these video streams/images directly, without going via the Live View page.

20
3.5 Network Camera Setup
This section describes how to configure the network camera, and is intended for product
Administrators, who have unrestricted access to all the Setup tools, and Operators, who have access
to the settings for Basic, Live View, Video & Image, Audio, Event, and System Configuration.
The network camera is configured by clicking Setup in the top right-hand corner of the Live View page.
Click on to access the online help that explains the setup tools.
When accessing the network camera for the first time,
the “Admin Password” dialog appears. Enter your admin
name and password, set by the administrator.
Note: If the password is lost, the network camera must
be reset to the factory default settings. See “3.8
Resetting to the Factory Default Settings”. The default
administrator username is ADMIN and password is 1234.
3.5.1 Basic Configuration
The device information is displayed on the Basic Configuration page.