Victor DC300 User manual

1
Need Help? Watch the video at www.victortech.com/High-Rise
High Rise™ Sit-Stand
Desk Converter
Assembly Instructions for Model DC300
PRE-ASSEMBLY
•Please read all instructions before beginning assembly. We strongly recommend
you watch the video at www.victortech.com/High-Rise.
•Remove all parts and hardware from box and lay out on a scratch-free work surface,
as this will avoid damaging any parts during assembly. The shipping box provides
an ideal work surface.
•Do not dispose of any contents or packaging material until assembly is complete.
This will help to avoid accidentally discarding small parts or hardware.
•For your safety and ease, adult assembly by two people is recommended.
•Use the parts and hardware lists to identify and separate each of the pieces included
prior to starting assembly.
•Do not use power tools. Use only the included Hex Key and Wrench. Power tools
can damage hardware and split wood.
Patent
Pending

2
Need Help? Watch the video at www.victortech.com/High-Rise
Bolt 5 pcs
Washer 2 pcs
Nut 2 pcs
Monitor Screws 4 pcs
Thumb Screw 1 pc
Hex Key 1 pc
Wrench 1 pc
Parts List
Missing Parts?
Call 1-800-628-2420 for
Victor customer service.
Hardware Bag:
Tower
Missing Parts or UPS Damaged Parts?
For your convenience you can E-mail us
at [e-mail]
If you require assistance during assembly, please watch
our video at Victortech.com/High-Rise
Or call our Customer Service Department
Monday –Friday 8 am to 4 pm CST 1-800-628-2420
Steel Base
Desk Surface
Monitor
Bracket
Stabilizers

3
Need Help? Watch the video at www.victortech.com/High-Rise
Step 1: Attach Tower to Steel Base
1-2 3 4 5
Use the Hex Key to attach the Tower to the Steel Base. Follow these steps:
1. Place the Steel Base on a flat and sturdy table with the felt pads facing down.
2. Using two hands, position the Steel Base so the five bolt holes are over the edge of
the table.
3. As shown above, place the Tower on top of the steel base and align the holes from
the Tower with the holes on the Base.
4. Take the bolts and hand feed them through the Base from underneath. Hand-tighten
the bolts until nearly tight. Keep bolts slightly loose until all are connected.
5. Use the small Hex Key to tighten the bolts more securely. Do not over tighten.
4
The Tower will be packaged in a compressed position. Do not loosen the knobs until
assembly is complete. This will make assembly easier.

4
Need Help? Watch the video at www.victortech.com/High-Rise
Step 2: Attach Desk Surface to Tower
1 2 3 4 - 6
Attach the Desk Surface to the Tower. (Note: Long bolts, washers, and spacers will already
be attached to the Desk Surface crossbar)
1. Place the Desk Surface on top of the Steel Base, as shown above.
2. Leave the thick spacer on each bolt.
3. Guide the two long bolts through the holes on the Tower. The thick spacer must be
between the crossbar and the Tower.
* Hint –moving the desk surface up and down while you are feeding the two
bolts through will assist you in this step. You can also lightly tap the bolts
through the Tower using a hammer.
4. Feed a small black washer onto each of the bolts on the other side of the Tower.
5. Feed a nut onto the end of each long bolt and hand tighten.
6. Use the included wrench to secure tightly.
Front View
Rear View

5
Need Help? Watch the video at www.victortech.com/High-Rise
Step 3: Attach Monitor Bracket to Monitor & Tower
1 2-4 5 6
1. The DC300 comes with a VERSA bracket designed to fit most monitors. Your
monitor is compatible if there are four screw holes in the center of the back of the
monitor.
2. Place the monitor with the screen facing down on a soft surface that will not
scratch the monitor.
3. Align the monitor bracket over the four screw holes.
TIP: The top of the bracket flange is wider.
4. Use the provided monitor screws to secure the monitor bracket to the computer
monitor.
5. Lift the monitor, and carefully place the monitor bracket flange into the receiving
slots of the DC300.
6. Once secure, insert the provided thumb screw into the small hole underneath the
bracket. This will secure the monitor in place.
4
3
5
6