Victory TS631 User manual

TS631 INSTRUCTION MANUAL
Step-by-Step Directions for programming TS631 Time Switch
Power On - Time Switch goes into time mode displaying Microsound TS631, the current day and time.
When programming is finished, the time switch must be in this mode.
To ring the bell manually, press B while in this mode
D Changes to the next mode
# Changes back to the last mode
A. To set the alarm time (when the bell/siren must be triggered)
1. Press D once to go into “Enter new alarm” mode.
2. Press * once to start programming the alarm times
3. Press: 1 for Monday / 2 for Tuesday / 3 for Wednesday /
4 for Thursday / 5 for Friday / 6 for Saturday / 7 for Sunday,
the cursor will then jump over to the zeros.
4. Enter time in 24 hour format hours 00: minutes :00: seconds :00
Note: Seconds must always be 00
E.g. 0 7 :4 5 :0 0 or 1 2 :0 0 :0 0 .
5. Press A to accept your new alarm. To clear an alarm time, press C .
6. Display will again show: Mon 00:00:00
7. Continue entering your alarms. When finished press D or # .
B. To view the alarms that have been programmed
1. Press * to view the times that have been programmed.
2. Press B to move forward to the next time. This can be done until the display shows “No more Alarms”.
To move back through alarms press A .
3. To delete only a selected alarm, press C while the alarm is shown on the display. The display will show
the next alarm.
4. Press # to go back to the time mode or D to go to the next mode
TS631 30 September 2009 Page 2 of 4

C. Copy alarms (if days have the same alarm times they can be copied)
1. Press * to enter programming mode.
2. With the cursor over the first Mon, press 1 – 7 (numerals representing the day of the week) to select the
day which you want to copy.
3. The cursor will jump to the next Mon, press the numeral representing the day you want to have the same
alarms copied to.
4. Press A to accept your choice. Display will say “Copying…” until done. It will then revert back to the
menu.
5. Only copies a single day to another, one at a time.
6. Press # to go back to the time mode or D to go to the next mode
D. Clear alarms (Beware: This clears all alarms)
1. Press * to delete all the alarms on the time switch. (Note: to delete only one alarm, see “View alarms”
above)
2. Press # to go back to the time mode or D to go to the next mode
E. Alarm duration
1. Press * to change the time in seconds that the alarm will sound. There will be no effect when the Alarm
mode is on “Latching”
2. Enter the time in seconds and press A to accept or C to clear the display.
3. The time switch will revert back to time mode.
F. Alarm mode
1. Pressing A when this option appears will alternate between “Pulsed” and “Latching”. Pulse mode must
always be selected to trigger Bells, Sirens, or the SLSI80 / M20 intercoms.
2. Press # to go back to the time mode or D to go to the next mode
G. Configure mode
1. Enables beep when any button is pressed. Press A to alternate between “on” and “off”.
2. Press # to go back to the time mode or D to go to the next mode
H. Arm alarm
1. Press A to alternate between “on” or “off”. When “On” alarms will ring as programmed. When “Off” all
alarms will be disabled.
2. Press # to go back to the time mode or D to go to the next mode
TS631 30 September 2009 Page 3 of 4

I. Table (To change between two programmed sets of alarms)
1. Press A to toggle the alarm between the two alarm tables. Use table one for permanent everyday alarms
and table two for special alarms. (This mode allows you to have special alarms without having to change
your permanent alarms.) Only one table can be used at a time.
2. Press # to go back to the time mode or D to go to the next mode
J. Enter new time (to adjust the current displayed time)
1. With the cursor over the Mon, press the numeral (1 – 7 ) representing the current day. The cursor will
jump over to the zeros.
2. Enter the current time in 24 hour format (hours 00: minutes :00: seconds :00)
E.g. 0 7 :4 5 :0 0 or 1 2 :0 0 :0 0 .
3. Press A to accept new time or C to cancel.
4. Program auto reverts to time mode.