Videology 45S10 User manual

®
IMAGING SOLUTIONS INC.
45S10 10.2” LCD Module
Instruction Manual
Information may change without notice.
This document provides technical information for the user. Videology reserves the right to
modify the information in this document as necessary. The customer should make sure that
they have the most recent manual version. Videology holds no responsibility for any errors
that may appear in this document.
Videology Imaging Solutions, Inc. USA Videology Imaging Solutions, B.V. Europe
37M Lark Industrial Parkway
Greenville, RI 02828
Tel: [phone]
Fax: [phone]
Neutronenlaan 4
NL-5405 NH Uden, Netherlands
Tel: [phone]
Fax: [phone]
Doc # INS-45S10 Issue Date: 10/30/2007
Revision: A Page 1 of 11

Doc # INS-45S10 Issue Date: 10/30/2007
Revision: A Page 2 of 11
Table Of Contents
1. Scope of Work .................................................................................................. 3
2. History............................................................................................................. 3
3. Specifications.................................................................................................... 3
4. Optical Specifications ......................................................................................... 3
5. Pin assignment ................................................................................................. 4
6. Inspection Standard........................................................................................... 6
6.1. Inspection Environment Conditions................................................................ 6
6.2. Classification of Defects............................................................................... 6
7. Reference of The Input Application....................................................................... 7
7.1. Drive Board w/Input Connectors/ Function Key Board ...................................... 7
7.1.1. Key Operation Manual........................................................................... 7
7.2. PCB Mechanical Dimensions.......................................................................... 8
8. Mechanical Drawing (PANEL only)........................................................................ 9
9. Contact.......................................................................................................... 11

Doc # INS-45S10 Issue Date: 10/30/2007
Revision: A Page 3 of 11
1. Scope of Work
These specifications shall be applied to: 45S10, 10.2”color TFT LCD module.
2. History
Revision Issue Date
Reason CN#
Rev A 08-22-2007 Initial release 07-0195
3. Specifications
Display 10.2” color TFT LCD (16:9)
Number of dots 800 x (R.G.B) x 480
Active Area 222(W) x 133.2(H)
Dot Pitch 0.1905(W) x 0. 1905 (H)
Color Configurations R.G.B stripe
Display Color 262144
Back Light CCFT
Input Signal 1 CH Composite video Input (RCA x 1)
NTSC/PAL auto switchable.
S-Video Input (4 Pin Min Din x 1)
PC-D Sub. Input. SVGA.
Audio Input 1CH RCA Input (Option)
Audio Output 2W(Option)
Power Input Voltage DC12±10%
Power Consumption 8.5W
External Control OSD Function Control:
Video: Contrast. Brightness. Color.
Hue (NTSC only). Saturation, Sharpness,
Color Temp (Warm, Cool), Display (Full, 4:3)
Operating Temperature -10℃~60℃
Storage Temperature -30℃~85℃
Overall Dimension 235(W) x 145.8(H) x 5.9(D) (Panel only)
Weight 305±10g (Panel only)
4. Optical Specifications
Lamp Life-time 40,000hr min. (at Temp =25℃)
Right 60 deg
Left 60 deg
Up 50 deg
Viewing Angle (min.)
Down 60 deg
Brightness 450 nit (typ.)
Contrast Ratio 300:1 typical
Response Time Tr: 12 ms Tƒ: 18ms (Typ)

Doc # INS-45S10 Issue Date: 10/30/2007
Revision: A Page 4 of 11
5. Pin assignment
TFT-LCD Panel Driving Section
Pin no Symbol I/O Description Remark
1 (POL) O Polarity selection
2 DIO2 O/P Vertical start pulse signal input or output
3 OE I Output enable
4 CPV I Vertical clock
5 DIO1 I Vertical start pulse signal input or output
6 GND I Power ground
7 (EDGSL) I Select rising edge or rising/falling edge
8 VCC I Digital voltage for source driver
9 (V12) I Gamma voltage level 12
10 VGL I Gate OFF voltage
11 (V14) I Gamma voltage level 14
12 VGH I Gate ON voltage
13 (V13) I Gamma voltage level 13
14 U/D I Up/down selection
15 VCOM1 I Common voltage
16 GND I Power ground
17 AVDD1 I Power supply for analog circuit
18 V10 I Gamma voltage level 10
19 V8 I Gamma voltage level 8
20 V6 I Gamma voltage level 6
21 V4 I Gamma voltage level 4
22 V2 I Gamma voltage level 2
23 GND I Power ground
24 R5 I Red data (MSB)
25 R4 I Red data
26 R3 I Red data
27 R2 I Red data
28 R1 I Red data
29 R0 I Red data (LSB)
30 GND I Power ground

Pin no Symbol I/O Description Remark
31 GND I Power ground
32 G5 I Green data (MSB)
33 G4 I Green data
34 G3 I Green data
35 G2 I Green data
36 G1 I Green data
37 G0 I Green data (LSB)
38 STHL I/O Horizontal start pulse signal input or output
39 INV I Control signal are inverted or not
40 GND I Power ground
41 DCLK I Sample clock
42 DVDD I Voltage for digital circuit
43 STHR I/O Horizontal start pulse signal input or output
44 LD I Latches the polarity of outputs and switches
the new data to outputs
45 B5 I Blue data (MSB)
46 B4 I Blue data
47 B3 I Blue data
48 B2 I Blue data
49 B1 I Blue data
50 B0 I Blue data (LSB)
51 R/L I Right/ left selection
52 V1 I Gamma voltage level 1
53 V3 I Gamma voltage level 3
54 V5 I Gamma voltage level 5
55 V7 I Gamma voltage level 7
56 V9 I Gamma voltage level 9
57 V11 I Gamma voltage level 11
58 AVDD2 I Voltage for analog circuit
59 GND I Power ground
60 VCOM2 I Common voltage
Doc # INS-45S10 Issue Date: 10/30/2007
Revision: A Page 5 of 11

6. Inspection Standard
6.1. Inspection Environment Conditions
Room Temperature: 20 ~ 25℃
Humidity: 65±5% RH
The viewing line should be perpendicular to the surface screen.
6.2. Classification of Defects
Dot Defect
A. Inspection condition
Inspection distance: 35±5cm
Inspection illumination: 100~150Lux
Panel temperature: 30±5℃
Inspection pattern: Full white, full black, red, green and blue screens.
B. Acceptable
Doc # INS-45S10 Issue Date: 10/30/2007
Revision: A Page 6 of 11
Area
Item A
B
Total
Blue Black 2 3 4
Red Green White 1 3 3
Total 2 5 7
C. The definitions of A and B zone
B
Scratch on the polarizer
Number = 3 max.
Width ≦0.1 mm, Length ≦6 mm
Dent on the polarizer
Number = 3 max., Average Diameter ≦0.3 mm
Foreign material on the polarizer
Number = 2 max, Average Diameter ≦0.5 mm
Afterimage
After displaying a pattern for 5 seconds then switch to a different pattern, the previous
pattern should disappear within 10 seconds.
A
V/4
V
V/2
H/4 H/2
H

7. Reference of The Input Application
7.1. Drive Board w/Input Connectors/ Function Key Board
7.1.1. Key Operation Manual
1. Press “POWER” to switch on the LCD monitor.
2. Press “Source” to select: AV1 -> S-Video -> PC.
3. Press “MENU” to get into the OSD operator: Contrast. Brightness. Color,
Hue (NTSC only). Saturation, Sharpness, Color Temp (Warm, Cool),
Display (Full, 4:3).
4. Press “UP” & “DOWN” to increase or decrease the setting.
5. Press “POWER” to switch off the power.
Doc # INS-45S10 Issue Date: 10/30/2007
Revision: A Page 7 of 11

7.2. PCB Mechanical Dimensions
Doc # INS-45S10 Issue Date: 10/30/2007
Revision: A Page 8 of 11

8. Mechanical Drawing (PANEL only)
Note: 1: 6’CLOCK DIRECTION IS THE OPTIMUM VIEWING ANGLE
2: GENERAL TOLERANCE：0.3mm
3: Connector：BHSR-02VS-1
Figure 1. Outline dimensions of TFT-LCD module (Front Side)
Doc # INS-45S10 Issue Date: 10/30/2007
Revision: A Page 9 of 11

Figure 2. Outline dimensions of TFT-LCD module (Rear Side)
Doc # INS-45S10 Issue Date: 10/30/2007
Revision: A Page 10 of 11