Viessmann VITOCAL 300-A Quick guide

Installation and service instructions
for contractors
VIESMANN
Vitocal 300-A
Type AWO-AC 301.B11 to B14
Air/water heat pump with electric drive, 400 V~
For applicability, see the last page
VITOCAL 300-A
5672 190 GB 7/2015 Please keep safe.

2
Please follow these safety instructions closely to
prevent accidents and material losses.
Safety instructions explained
Danger
This symbol warns against the risk of injury.
!Please note
This symbol warns against the risk of material
losses and environmental pollution.
Note
Details identified by the word "Note" contain additional
information.
Target group
These instructions are exclusively intended for author-
ised contractors.
■Work on the refrigerant circuit may only be carried
out by authorised refrigeration engineers.
■Work on electrical equipment must only be carried
out by a qualified electrician.
■The system must be commissioned by the system
installer or a qualified person authorised by the
installer.
Regulations to be observed
■National installation regulations
■Statutory regulations for the prevention of accidents
■Statutory regulations for the protection of the envi-
ronment
■Codes of Practice of the relevant trade associations
■All relevant safety regulations as defined by DIN, EN,
DVGW, VDE and locally applicable standards
aÖNORM, EN and ÖVE
cSEV, SUVA, SVTI, SWKI and SVGW
Working on the system
■Isolate the system from the power supply (e.g. by
removing the separate fuse or by means of a mains
isolator) and check that it is no longer 'live'.
Note
In addition to the control circuit there may be several
load circuits.
Danger
Contact with 'live' components can result in
severe injuries. Some components on PCBs
remain 'live' even after the power supply has
been switched off.
Wait at least 4 minutes before removing equip-
ment covers, to allow the voltage to dissipate.
■Safeguard the system against reconnection.
!Please note
Electronic assemblies can be damaged by elec-
trostatic discharge.
Prior to commencing work, touch earthed
objects such as heating or water pipes to dis-
charge static loads.
Repair work
!Please note
Repairing components that fulfil a safety func-
tion can compromise the safe operation of your
system.
Replace faulty components with genuine
Viessmann spare parts.
Auxiliary components, spare and wearing parts
!Please note
Spare and wearing parts that have not been tes-
ted together with the system can compromise its
function. Installing non-authorised components
and making non-approved modifications or con-
versions can compromise safety and may inva-
lidate our warranty.
For replacement, use only spare parts supplied
or approved by Viessmann.
Safety instructions
Safety instructions
5672 190 GB

3
1. Information Disposal of packaging ............................................................................ 5
Symbols ................................................................................................. 5
Intended use .......................................................................................... 5
Product information ................................................................................ 6
2. Preparing for installation Requirements concerning on-site connections ...................................... 7
Siting and transport requirements .......................................................... 7
■Transportation ..................................................................................... 7
■Installation site requirements .............................................................. 8
■Requirements for the heat pump control unit installation location ...... 8
■Minimum clearances ........................................................................... 9
■Foundation .......................................................................................... 9
■Cables and hydraulic lines .................................................................. 11
3. Installation sequence Installing the heat pump ......................................................................... 15
Making the hydraulic connections .......................................................... 16
■Connect heating water flow and heating water return at the heat
pump ................................................................................................... 16
■Connect heating circuits and DHW cylinder in the building ................ 16
■Fitting the flow temperature sensor, secondary circuit ....................... 17
■Connecting the condensate drain and routing the ribbon heater ........ 17
Electrical connections, heat pump ......................................................... 20
■Opening the wiring chamber ............................................................... 21
■Connecting cables .............................................................................. 22
Installing the heat pump control unit ...................................................... 23
■Fitting wall mounting base and casing base ....................................... 23
■Fitting the casing front ........................................................................ 23
■Opening the heat pump control unit ................................................... 25
Electrical connections, heat pump control unit ...................................... 25
■Inserting cables/leads and applying strain relief ................................. 25
■Connecting cables .............................................................................. 26
■Adapting the heat pump control unit ................................................... 27
■Plugging in the coding card ................................................................ 27
■Overview of electrical connections ..................................................... 28
■Main PCB (function components 230 V~) .......................................... 29
■Expansion PCB (230 V~ components) ............................................... 31
■Cross connect PCB (signal and safety connections) .......................... 34
■Controller and sensor PCB (sensors) ................................................. 37
Power supply ......................................................................................... 39
■Heat pump control unit power supply 230 V~ ..................................... 40
■Compressor power supply 400 V~ ..................................................... 41
■Power supply with power-OFF: Without on-site load disconnect ....... 41
■Power supply with power-OFF: With on-site load disconnect ............ 42
■Mains power supply in conjunction with on-site power consumption . 44
■Smart Grid .......................................................................................... 44
Closing the heat pump ........................................................................... 45
4. Commissioning, inspec-
tion, maintenance
Steps - commissioning, inspection and maintenance ............................ 50
5. Maintenance Overview of electrical components ........................................................ 63
Removing the outer casing .................................................................... 63
Removing the side panel ....................................................................... 64
Opening the electrical wiring chamber ................................................... 64
Overview of internal components .......................................................... 65
Draining heat pump on the secondary side ........................................... 66
Checking sensors .................................................................................. 66
■Viessmann NTC 10 kΩ (marked blue) ................................................ 66
■Viessmann Pt500A (green ID label) ................................................... 67
Index
Index
5672 190 GB

4
Checking MCB/fuses ............................................................................. 67
■Fan ..................................................................................................... 67
■Heat pump control unit ....................................................................... 67
6. Parts lists Overview of assemblies ......................................................................... 69
Casing .................................................................................................... 70
Base frame ............................................................................................ 72
Heat pump module ................................................................................ 74
Additional components .......................................................................... 78
Air module .............................................................................................. 80
Miscellaneous ........................................................................................ 82
Electrical equipment .............................................................................. 84
Heat pump control unit ........................................................................... 86
7. Commissioning/service
reports
Hydraulic parameter report .................................................................... 88
Control parameters report ...................................................................... 88
8. Specification ................................................................................................................ 96
9. Appendix Commissioning order ............................................................................. 98
Final decommissioning and disposal ..................................................... 98
10. Certificates Declaration of conformity ....................................................................... 99
11. Keyword index ................................................................................................................100
Index
Index (cont.)
5672 190 GB

5
Please dispose of packaging waste in line with statu-
tory regulations.
DE: Use the disposal system organised by
Viessmann.
AT: Use the ARA statutory disposal system (Altstoff
Recycling Austria AG, licence number 5766).
CH: Packaging waste is disposed of by the HVAC
contractor.
Symbols
Symbol Meaning
Reference to other document containing
further information
1.
Step in a diagram:
The numbers correspond to the order in
which the steps are carried out.
Warning of material losses and environ-
mental pollution
Live electrical area
Pay particular attention.
■Component must audibly click into place.
or
■Acoustic signal
■Fit new component.
or
■In conjunction with a tool: Clean the sur-
face.
Dispose of component correctly.
Dispose of component at a suitable collec-
tion point. Do not dispose of component in
domestic waste.
The steps in connection with commissioning, inspec-
tion and maintenance are found in the "Commission-
ing, inspection and maintenance" section and identified
as follows:
Symbol Meaning
Steps required during commissioning
Not required during commissioning
Steps required during inspection
Not required during inspection
Steps required during maintenance
Not required during maintenance
Intended use
The appliance is only intended to be installed and
operated in sealed unvented heating systems that
comply with EN 12828, with due attention paid to the
associated installation, service and operating instruc-
tions.
Depending on the version, the appliance can only be
used for the following purposes:
■Central heating
■Central cooling
■DHW heating
Information
Disposal of packaging
5672 190 GB
Information

6
The range of functions can be extended with additional
components and accessories.
Intended use presupposes that a fixed installation in
conjunction with permissible, system-specific compo-
nents has been carried out.
Commercial or industrial usage for a purpose other
than central heating/cooling or DHW heating shall be
deemed inappropriate.
Incorrect usage or operation of the appliance (e.g. the
appliance being opened by the system user) is prohibi-
ted and will result in an exclusion of liability. Incorrect
usage also occurs if the components in the heating
system are modified from their intended function.
Note
The appliance is intended exclusively for domestic or
semi-domestic use, i.e. even users who have not had
any instruction are able to operate the appliance
safely.
Product information
Design
Vitocal 300-A is an output-dependent control air/water
heat pump for siting outside a building.
The integral radial fan sucks the outdoor air from all
sides through the circular evaporator via the air intake
grille in the central area of the heat pump. The chilled
air leaves the heat pump through the air discharge
grille near ground level. This air flow concept allows
the system to operate quietly.
The refrigerant circuit operates using steam injection
and has 2 separately controlled electronic expansion
valves. Flow air temperatures of up to 65 °C are possi-
ble.
Output control
The requested compressor output is controlled via a
DC inverter.
Hydraulics
The heat pump has one connection each for heating
water flow and return. The heating water enters the
building via hydraulic connection lines. These lines are
routed below ground and are frost-proof.
In the secondary circuit, the following components can
be installed in the building:
■1 HE circulation pump for DHW heating and 1 HE
circulation pump for central heating
or
■1 HE circulation pump and the 3-way diverter valve
for "Heating/DHW heating"
Central heating
The heat pump can supply up to 3 heating circuits: 1
heating circuit without mixer and 2 heating circuits with
mixer. The mixer extension kit (accessories) is
required to control the mixer for the second heating cir-
cuit with mixer.
Central cooling
Central cooling can result either through a heating/
cooling circuit or via a separate cooling circuit. The
refrigerant circuit is reversed and heat removed from
the cooling circuit.
Heat pump control unit
The entire heating system is monitored and controlled
by the heat pump control unit Vitotronic 200, type
WO1C.
The heat pump control unit is installed on a wall inside
the building and connected electrically with the heat
pump.
Information
Intended use (cont.)
5672 190 GB
Information

7
1998
100
Ø 1100
B C
300
370
490
B
C
DA
211
945
Fig. 1
AElectrical cable entries
BHeating water flow
Connection G 1¼ with adaptor G 1¼ to Rp 1
CHeating water return
Connection G 1¼ with adaptor G 1¼ to Rp 1
DCondensate drain hose (flexible)
Siting and transport requirements
Transportation
The appliance can be lifted onto the foundation with,
for example, a crane and on-site equipment. !Please note Lifting by screwed-in crane lugs causes appli-
ance damage.
■Do not attach crane lugs to the heat pump.
■Lift the heat pump with 2 or 4 transport straps.
Route opposite loops around the upper frame.
■Ensure even load distribution.
Preparing for installation
Requirements concerning on-site connections
5672 190 GB
Installation

8
!Please note
Impacts, compression and tensile loads can
cause damage to the outside panels of the
appliance.
Never put weight on the top, front or side panels
of the appliance.
!Please note
Tilting the compressor at a steep angle inside
the heat pump can result in appliance damage.
Max. tilting angle: 45°
Installation site requirements
The heat pump may only be sited outside the build-
ing on solid foundations: See page 9.
■Provide a manual drain for the heating water flow
and return lines in any area at risk from frost.
Drain the system if the heat pump is shut down or
there is a prolonged power failure.
■If the heat pump control unit, secondary pump and
heating circuit pumps are ready for operation, the
frost protection function of the heat pump control unit
is enabled.
In heat pump systems where a power failure would
not be detected, e.g. holiday home: Operate the
heating circuit with a suitable antifreeze or drain the
heating circuit.
■To prevent an increase in noise level due to reflec-
tion, avoid siting equipment in recesses, at building
corners or between 2 walls.
■Site the heat pump so that it is protected against
strong winds.
Note
In heavy snowfall, the air discharge grilles in the
lower area of the heat pump must be kept free of
snow and ice.
■Lawn areas and vegetation can reduce noise devel-
opment. Only the heat pump foundations should
therefore be made from reverberant material (con-
crete).
■Provide drainage or sewer pipes for draining the con-
densate.
■Never install the heat pump next to living rooms or
bedrooms.
■The air in the discharge area is approx. 10 K colder
than the ambient air. Therefore, black ice could
develop in the discharge area even at [ambient] tem-
peratures above freezing. Observe a clearance of
≥ 3 m to pavements or terraces.
Requirements for the heat pump control unit installation location
The heat pump control unit may only be installed
inside the building on a wall: See page 23.
!Please note
Unfavourable ambient conditions can lead to
malfunctions and appliance damage.
■The installation room must be dry and free
from the risk of frost.
■Ensure ambient temperatures between 0 and
35 °C.
Danger
Dust, gases and vapours can be damaging to
health and trigger explosions.
Avoid dust, gases and vapours in the installation
room.
Preparing for installation
Siting and transport requirements (cont.)
5672 190 GB
Installation

9
Minimum clearances
1500
1500
1500
1500
Fig. 2
Foundation
Site the heat pump level on a durable and solid base.
We recommend laying a concrete foundation as
described in the following chapters. The thickness of
cover represents an average value and should be
matched to local conditions. This must be done in
accordance with the standard rules of building engi-
neering.
■Design the foundations, mounting surface and pipe-
work in such a way as to prevent small animals from
entering the heat pump and the cable ducts.
■Drain all condensate derived from the air via a DN 40
drain pipe, which must be protected from frost and
provide a constant fall.
Amount of condensate: Subject to temperature and
relative humidity, up to 20 l/h and up to 20 l in 5 min
during defrosting.
Connect the condensate drain to a drainage or
sewer system. In this case, provide a siphon with a
backup level of at least 60 mm in the frost-protec-
ted area.
■Where appropriate, provide thermal insulation or a
ribbon heater around the condensate drain on site.
Technical guides for heat pumps
Weight including outer casing: 250 kg
Preparing for installation
Siting and transport requirements (cont.)
5672 190 GB
Installation

10
Foundation dimensions
No recess in the foundation for cables and hydraulic
lines required.
Plan view Sectional view
198
291
411
514
A
H H
H
860
700
53
83
70
F
G
CDE
B
Fig. 3
400
500
900
300
400
H
G
E
C
D
F A
H
K
B
C
BG
E
D
L
Fig. 4
AHeat pump
BConcrete foundation (300 mm thick) consisting of:
■Concrete slab C25/30, BSt 500 S and M
■Reinforcement with all-round wire mesh made of
Q 257 A
CKG conduit DN 100 for power cable 400 V/50 Hz
(on site)
DKG conduit DN 100 for connecting cables to the
heat pump control unit (on site): Control cable
230 V~, LV lead < 42 V
EHydraulic connection set (accessory): Hydraulic
connection lines for heating water flow and heating
water return
FHydraulic connections on the heat pump (heating
water flow and heating water return)
GCondensate drain DN 40 (on site)
HSoft ground, gravel or crushed stone
KFrost protection (for example compacted crushed
stone 0 to 32/56 mm); layer thickness subject to
local requirements and building rules
LTop edge of concrete foundation
Preparing for installation
Siting and transport requirements (cont.)
5672 190 GB
Installation

11
Cables and hydraulic lines
Laying the lines underground and routing in through the exterior wall
O NS M PQ R
T
U
C
D
E
F
O N M
K
B
O N M
400
900
D CE
P
Fig. 5
BConcrete foundation (300 mm thick) consisting of:
■Concrete slab C25/30, BSt 500 S and M
■Reinforcement with all-round wire mesh made of
Q 257 A
CKG conduit DN 100 for power cable 400 V/50 Hz
(on site)
DKG conduit DN 100 for connecting cables to the
heat pump control unit (on site): Control cable
230 V~, LV lead< 42 V
EHydraulic connection set (accessory): Connection
lines for heating water flow and heating water
return
FCondensate drain DN 40 (on site)
KFrost protection (compacted crushed stone, e.g. 0
to 32/56 mm); layer thickness subject to local
requirements and standard rules of building engi-
neering
MPower cable, compressor/fan (3/N/PE 400 V/
50 Hz, on site)
Recommended cable: 5 x 2.5 mm2, flexible
N2 connecting cables inside DN 100 KG conduit (on
site), fully wired (5, 15 or 30 m):
■Control cable 230 V~
■LV lead < 42 V
Note
The maximum cable length is 30 m. Extensions
are not permissible.
OHydraulic connection lines (heating water flow and
heating water return)
PUnderground channel
QWall duct with expanding mortar (on site) for
hydraulic connection line
RMoisture-proof and waterproof wall ducts (on site)
SDrain & fill facility with shut-off valve (for draining
with compressed air)
Preparing for installation
Siting and transport requirements (cont.)
5672 190 GB
Installation

12
TExpansion vessel with safety assembly (accesso-
ries)
UClearance, house wall — foundations:
■Maximum clearance depends on length of the
connecting cables and hydraulic connection
lines: Max. 23 m
■Maintain the minimum clearance to other objects
(> 1.5 m) when siting.
Heating water connection (hydraulic connection
lines O)
Use the hydraulic connection set (accessory). The
connection set is fully prepared in different lengths.
The flow and return lines are flexible and have 2 adap-
tors each. The lines are located inside a common ther-
mal insulation.
■Flow/return line: 2 x DN 32
■Adaptor fittings: 4 x DA 40 to R 1¼
■Lines are fed into building Q through a wall duct
with expanding mortar (on site).
■Provide a drain & fill facility S for heating water flow
and return in the building near an external wall and
0.8 m below ground level.
Note
In buildings at ground level, provide a thermally insu-
lated duct or enable draining of the heat pump with
compressed air.
Frost protection
If the heat pump control unit and heating circuit pump
are ready for operation, the frost protection function of
the heat pump control unit is enabled. Drain the sys-
tem via the drain & fill facility S when the heat pump
is taken out of use or if the power fails for a long
period.
In heat pump systems where a power failure would not
be detected (holiday home), the heating circuits can be
operated with suitable antifreeze. Ensure that the sys-
tem components used are compatible with the anti-
freeze.
Power cable M
■Run power cable M to the heat pump outside the
building in a KG conduit DN 100.
■Cable length required in the heat pump from top
edge of foundation: Min. 0.7 m
■Observe the regulations imposed by your local
power supply utility.
Connecting cables N
Route prepared connecting cables (control cable
230 V~, LV lead < 42 V) N outside the building in a
KG conduit DN 100. Protect the plugs at the ends of
the cables from dirt and damage (e.g. with bubble
wrap).
Cable length required in the heat pump from top edge
of foundation
■Control cable 230 V~: Min. 0.9 m
■LV lead < 42 V: Min. 0.7 m
Routing KG conduits C, D
■Provide a wire pull for the cables (M, N).
■To facilitate the routing of cables D through the KG
conduit, avoid 90° bends; instead use 3 x 30° or 2 x
45°.
■Route the KG conduit with a slope towards the heat
pump and fit a condensate drain if required.
■Ensure that wall ducts R are moisture-proof and
waterproof.
■Seal the apertures of the KG conduit so that no ani-
mals or moisture can enter the building.
Preparing for installation
Siting and transport requirements (cont.)
5672 190 GB
Installation

13
Required cables and hydraulic lines
G
K
P
C
F
L
O Q
H
S
D
E
M
N
R
A
B
Fig. 6
AHeat pump
BElectric terminal area in the heat pump
CPower cable, compressor/fan (3/N/PE 400 V/
50 Hz, on site)
D2 connecting cables inside DN 100 KG conduit (on
site), fully wired (5, 15 or 30 m):
■Control cable 230 V~
■LV lead < 42 V
Note
The maximum lead length is 30 m. Extensions
are not permissible.
EHeat pump control unit power cable
Recommended cable: 3 x 1.5 mm2 (5 x 1.5 mm2
with power-OFF)
FConnection cables for further components and
functions (e.g. pumps, sensors, fault messages,
etc.)
GHeat pump control unit
HInstantaneous heating water heater control
Recommended cable: 5 x 2.5 mm2
KSwitching module for instantaneous heating water
heater: Connecting chamber with 2 output relays;
install inside the building.
LPower cable, instantaneous heating water heater
(if installed), max. output 9 kW
MConnecting cable with plug for switching module/
instantaneous heating water heater, approx. 1.6 m
long
NFlow temperature sensor, secondary circuit: Install
in the heating water flow inside the building.
Cable with plug, 2.0 m long: Extend on site if
required.
OFlow, heating circuits with secondary pump/flow,
DHW cylinder with circulation pump for cylinder
heating (both circulation pumps are accessories):
Alternatively, 1 secondary pump and a 3-way
diverter valve can also be used (both accessories).
PInstantaneous heating water heater (accessory;
install in building)
QHeating water return
RHydraulic connection set (accessory): Connection
lines for heating water flow and return
SDrain & fill facility with shut-off valve (for draining
with compressed air)
Preparing for installation
Siting and transport requirements (cont.)
5672 190 GB
Installation

14
Required cable lengths:
■For the heat pump control unit (wall outlet centrally
directly below the heat pump control unit):
0.6 m from the wall outlet
■Inside the heat pump (to the electric terminal area):
0.7 m from the top edge of the foundations
Preparing for installation
Siting and transport requirements (cont.)
5672 190 GB
Installation

15
4x
2.
4x
4x
4x
3.
4.
5.
Fig. 7
1. Position the heat pump according to the details on
page 7.
2. Align the appliance horizontally.
If the adjustable feet are used to compensate for an
uneven floor (max. 10 mm), the pressure load on
the feet must be distributed evenly.
Installation sequence
Installing the heat pump
5672 190 GB
Installation

16
Connect heating water flow and heating water return at the heat pump
!Please note
Mechanically loaded hydraulic connections lead
to leaks, vibration and appliance damage.
■Connect supplied connecting hoses (bends)
so that they are free of load and torque stress.
■To prevent transmission of any vibration, the
connecting hoses must not contact any other
components.
Note
■The connecting hoses can be shortened.
■Completely encase connecting hoses in the supplied
thermal insulation.
C
AB
2x
2.
1.
4.
3.
B
A
Fig. 8
AHeating water return
BHeating water flow
CHydraulic connection set (accessory)
Connect heating circuits and DHW cylinder in the building
1. Equip the secondary circuit on site with an expan-
sion vessel and safety assembly (in accordance
with EN 12828).
Fit the safety assembly to the on-site line in the
heating water return.
2. Connect secondary lines to the lines of the
hydraulic connection set (accessory).
!Please note
Mechanically loaded hydraulic connections
lead to leaks, vibration and appliance dam-
age.
Connect on-site lines so that they are free of
load and torque stress.
3. !Please note
Leaking hydraulic connections lead to appli-
ance damage.
■Check the tightness of the internal and on-
site hydraulic connections.
■In the event of leaks, drain off liquid via the
drain valve. Check the seating of seal
rings. Always replace displaced seal rings.
Observe information regarding filling and venting:
See page 51.
4. Thermally insulate pipes inside the building.
5. Connect the drain hose to the safety valve.
Connect the drain hose to the public sewage sys-
tem with a fall and a pipe vent.
Installation sequence
Making the hydraulic connections
5672 190 GB
Installation

17
Note
■In underfloor heating circuits, install a temperature
limiter to restrict the maximum temperature of under-
floor heating systems.
■Safeguard the minimum flow rate: See "Specifica-
tion".
Fitting the flow temperature sensor, secondary circuit
The flow temperature sensor for the secondary circuit
is installed in the heating water flow inside the build-
ing.
Note
If an instantaneous heating water heater is installed, fit
the flow temperature sensor for the secondary circuit in
the heating water flow downstream of the instantane-
ous heating water heater.
2.
3.
D
C
B
1.
A
Fig. 9
APipe section with sensor well
BSpring clip
CFlow temperature sensor, secondary circuit
DSensor lead plug and lead to the heat pump con-
trol unit
1. Fit the pipe section with a sensor well.
2. Secure the flow temperature sensor for secondary
circuit with a spring clip in the sensor well.
3. Connect the sensor lead and the lead to the heat
pump control unit.
4. Connect the lead to the heat pump control unit to
the controller and sensor PCB inside the heat pump
control unit at connection F8. If necessary, extend
the lead to the heat pump control unit on site.
Connecting the condensate drain and routing the ribbon heater
Note
■Subject to temperature and relative humidity of the
drawn air, up to 20 l of condensate per hour can
occur in the appliance.
■During the defrosting process, the amount of con-
densate can be as high as 20 l within 5 min.
■Connect condensate drain via siphon (backup level
at least 60 mm) in the frost-protected area to on-site
drain connection (drainage or sewer system): See
page 11.
■Route condensate drain (drain pipe DN 40) with a
constant fall of at least 2 %.
■Where appropriate, provide thermal insulation or a
ribbon heater around the condensate drain on site.
Installation sequence
Making the hydraulic connections (cont.)
5672 190 GB
Installation

18
1.
2.
Fig. 10
Notes on routing the electric ribbon heater
■Maintain a bend radius of 20 mm.
■Never route the ribbon heater along sharp edged
components.
Installation sequence
Making the hydraulic connections (cont.)
5672 190 GB
Installation

19
3.
4.
Fig. 11
Installation sequence
Making the hydraulic connections (cont.)
5672 190 GB
Installation

20
5.
6.
7.
Fig. 12
Electrical connections, heat pump
Danger
Damaged wiring insulation wiring can lead to
serious injury from electrical current and result in
appliance damage.
Route cables so that they cannot touch very hot,
vibrating or sharp-edged components.
Installation sequence
Making the hydraulic connections (cont.)
5672 190 GB
Installation