ViewSonic PD1910 User manual

PD1910
Pen Display
User Guide
Model No. VS15570
IMPORTANT: Please read this User Guide to obtain important information
on installing and using your product in a safe manner, as well as
registering your product for future service. Warranty information contained
in this User Guide will describe your limited coverage from ViewSonic
Corporation, which is also found on our web site at http://www.viewsonic.
com in English, or in specic languages using the Regional selection box
in the upper right corner of our website. “Antes de operar su equipo lea cu
idadosamente las instrucciones en este manual”

i
FCC Compliance Statement
This device complies with part 15 of FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful interfer-
ence, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radi-
ate radio frequency energy, and if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particu-
lar installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
yReorient or relocate the receiving antenna.
yIncrease the separation between the equipment and receiver.
yConnect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
yConsult the dealer or an experienced radio/TV technician for help.
Warning: You are cautioned that changes or modications not expressly
approved by the party responsible for compliance could void your authority
to operate the equipment.
Industry Canada Statement
CAN ICES-3 (B)/NMB-3(B)
Compliance Information

ii
The mark shown to the right is in compliance with the Waste Electri-
cal and Electronic Equipment Directive 2002/96/EC (WEEE).
The mark indicates the requirement NOT to dispose the equipment as
unsorted municipal waste, but use the return and collection systems
according to local law.
If the batteries, accumulators and button cells included with this
equipment, display the chemical symbol Hg, Cd, or Pb, then it means
that the battery has a heavy metal content of more than 0.0005%
Mercury or more than, 0.002% Cadmium, or more than 0.004% Lead.

iii
Important Safety Instructions
1. DO NOT place objects on top of the device, as objects may scratch the
screen.
2. DO NOT expose the device to dirty or dusty environments.
3. DO NOT place the device on an uneven or unstable surface.
4. DO NOT insert any foreign objects into the device.
5. DO NOT expose the device to strong magnetic or electrical eld.
6. DO NOT expose the device to direct sunlight as it can damage the LCD
Screen. Keep it away from heat sources.
7. DO NOT use the device in the rain.
8. Please check with your Local Authority or retailer for proper disposal of
electronic products.
9. The device may produce some heat during normal operation or
charging. To prevent discomfort or injury from heat exposure, DO NOT
leave the device on your lap.
10.POWER INPUT RATING: Refer to the rating label on the device. Only
use accessories specied by the manufacturer.
11.DO NOT use any sharp object to tap the screen.
12.Clean the touch screen with a soft cloth. If needed, dampen the cloth
slightly before cleaning. Never use abrasives or cleaning solutions.
13.Disconnect the device from an electrical outlet and power off before
cleaning the device.
14.DO NOT disassemble the device. Only a certied service technician
should perform repair.

iv
Declaration of RoHS2 Compliance
This product has been designed and manufactured in compliance with
Directive 2011/65/EU of the European Parliament and the Council on
restriction of the use of certain hazardous substances in electrical and
electronic equipment (RoHS2 Directive) and is deemed to comply with
the maximum concentration values issued by the European Technical
Adaptation Committee (TAC) as shown below:
Substance Proposed Maximum
Concentration
Actual
Concentration
Lead (Pb) 0.1% < 0.1%
Mercury (Hg) 0.1% < 0.1%
Cadmium (Cd) 0.01% < 0.01%
Hexavalent Chromium (Cr6+) 0.1% < 0.1%
Polybrominated biphenyls (PBB) 0.1% < 0.1%
Polybrominated diphenyl ethers
(PBDE) 0.1% < 0.1%
Certain components of products as stated above are exempted under the
Annex III of the RoHS2 Directives as noted below:
Examples of exempted components are:
1. Mercury in cold cathode uorescent lamps and external electrode
uorescent lamps (CCFL and EEFL) for special purposes not exceeding
(per lamp):
(1) Short length (≦500 mm): maximum 3.5 mg per lamp.
(2) Medium length (＞500 mm and ≦1,500 mm): maximum 5 mg per
lamp.
(3) Long length (＞1,500 mm): maximum 13 mg per lamp.
2. Lead in glass of cathode ray tubes.
3. Lead in glass of uorescent tubes not exceeding 0.2% by weight.
4. Lead as an alloying element in aluminium containing up to 0.4% lead by
weight.
5. Copper alloy containing up to 4% lead by weight.
6. Lead in high melting temperature type solders (i.e. lead-based alloys
containing 85% by weight or more lead).
7. Electrical and electronic components containing lead in a glass or
ceramic other than dielectric ceramic in capacitors, e.g. piezoelectronic
devices, or in a glass or ceramic matrix compound.

v
Copyright Information
Copyright © ViewSonic®Corporation, 2013. All rights reserved.
ViewSonic and the three birds logo are registered trademarks of ViewSonic
Corporation.
Disclaimer: ViewSonic Corporation shall not be liable for technical or edito-
rial errors or omissions contained herein; nor for incidental or consequential
damages resulting from furnishing this material, or the performance or use of
this product.
In the interest of continuing product improvement, ViewSonic Corporation
reserves the right to change product specications without notice. Informa-
tion in this document may change without notice.
No part of this document may be copied, reproduced, or transmitted by any
means, for any purpose without prior written permission from ViewSonic
Corporation.
Product Registration
To meet your future needs, and to receive any additional product informa-
tion as it becomes available, please register your product on the Internet at:
www.viewsonic.com.
For Your Records
Product Name: PD1910
ViewSonic Pen Display
Model Number: VS15570
Document Number: PD1910_UG_ENG Rev. 1A 07-09-13
Serial Number: ____________________________________
Purchase Date: ____________________________________
Product disposal at end of product life
ViewSonic respects the environment and is committed to working and living
green. Thank you for being part of Smarter, Greener Computing. Please visit
ViewSonic website to learn more.
USA & Canada: http://www.viewsonic.com/company/green/recycle-program/
Europe: http://www.viewsoniceurope.com/uk/support/recycling-information/
Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx

vi
Contents
Compliance Information............................................................ i
Important Safety Instructions...................................................iii
Declaration of RoHS2 Compliance..........................................iv
Copyright Information .............................................................. v
Product Registration................................................................ v
1. Introduction.......................................................................... 1
1.1 Packing List ..................................................................................... 1
1.2 Product Overview ............................................................................ 1
2. Handwriting on the LCD screen........................................... 3
2.1 Using the Stylus .............................................................................. 3
2.2 Controlling the Stylus ...................................................................... 4
2.3 Featured Applications...................................................................... 5
3. Screen Positioning Settings................................................. 6
3.1 Mapping........................................................................................... 6
3.2 Pen Settings .................................................................................... 8
4. System Requirements ......................................................... 9
5. Installing the Pen Display Driver.......................................... 9
6. Uninstalling the Pen Display Driver ................................... 10
7. Troubleshooting................................................................. 11
7.1 Monitor problems........................................................................... 11
7.2 Interactive Pen Problems .............................................................. 12
8. Cleaning the Pen Display .................................................. 13
9. Product Specication......................................................... 14
Customer Support ................................................................. 16
Limited Warranty ................................................................... 17

1
1. Introduction
1.1 Packing List
After unpacking, make sure that all of the following contents are included:
yyPen Display
yyPower cord
yyPower Adapter
yyQuick Star Guide
yyDriver CD
yyVGA cable
yyUSB cable
yyPen
yyPen holder with including Pen tip
yyWarranty card*1 (China only)
If there is a defect or missing part, please contact the agency where you
purchased the product.
1.2 Product Overview
1.2.1 Front and Side View



 
①Display and pen touch area
②Control key buttons
③Power indication
④D-Sub
⑤DVI
⑥DC in
⑦USB port

2
1.2.2 Rear View

①Stand
Caution: Avoid the risk of electric shock. Do not open the shell by yourself.
Please contact maintenance personnel if any problems are encountered.

3
2. Handwriting on the LCD screen
2.1 Using the Stylus
Use the stylus in the same way that you would use a regular pen, with a
few differences. Use your thumb or index nger to control stylus function
button. Pressing the button has the same function as a right-button click on
a mouse by default. You can choose the button function from the list below
in the Pen Setting interface.