ViewSonic PJ558D User manual

PJ558D
DLP Projector
ViewSonic®
Model No. : VS11529
- User Guide
- Guide de l’utilisateur
- Guía del usuario
- Guia do usuário
- 使用手冊 (繁體)
- 使用手冊(简体)

ViewSonic PJ558Di
Compliance Information
For U.S.A.
This device complies with part 15 of FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.This
equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy, and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Warning: You are cautioned that changes or modications not expressly approved by the party
responsible for compliance could void your authority to operate the equipment.
For Canada
• This Class B digital apparatus complies with Canadian ICES-003.
• Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
CE Conformity for European Countries
The device complies with the requirements of the EEC directive 89/336/EEC as
amended by 92/31/EEC and 93/68/EEC Art.5 with regard to “Electromagnetic
compatibility”, and 73/23/EEC as amended by 93/68/EEC Art.13 with regard to
“Safety.”
Following information is only for EU-member states:
The mark shown to the right is in compliance with the Waste Electrical and
Electronic Equipment Directive 2002/96/EC (WEEE).
The mark indicates the requirement NOT to dispose the equipment as unsorted
municipal waste, but use the return and collection systems according to local law.

iiViewSonic PJ558D
Important Safety Instructions
1. Read these instructions completely before using the equipment.
2. Keep these instructions in a safe place.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this equipment near water. Warning: To reduce the risk of re or electric shock,
do not expose this apparatus to rain or moisture.
6. Clean with a soft, dry cloth. If further cleaning is required, see “Cleaning the Display” in this
guide for further instructions.
7.
Do not block any ventilation openings. Install the equipment in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other devices
(including ampliers) that produce heat.
9. Do not attempt to circumvent the safety provisions of the polarized or grounding-type plug.
A polarized plug has two blades with one wider than the other. A grounding type plug has
two blades and a third grounding prong. The wide blade and the third prong are provided for
your safety. If the plug does not t into your outlet, consult an electrician for replacement of
the outlet.
10. Protect the power cord from being tread upon or pinched, particularly at the plug, and the
point where if emerges from the equipment. Be sure that the power outlet is located near the
equipment so that it is easily accessible.
11. Only use attachments/accessories specied by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the equipment. When a cart is used, use caution when
moving the cart/equipment combination to avoid injury from tipping over.
13. Unplug this equipment when it will be unused for long periods of time.
14. Refer all servicing to qualified service personnel. Service is required when the unit has
been damaged in any way, such as: if the power-supply cord or plug is damaged, if liquid is
spilled onto or objects fall into the unit, if the unit is exposed to rain or moisture, or if the
unit does not operate normally or has been dropped.

ViewSonic PJ558Diii
Declaration of RoHS Compliance
This product has been designed and manufactured in compliance with Directive 2002/95/EC of
the European Parliament and the Council on restriction of the use of certain hazardous substances
in electrical and electronic equipment (RoHS Directive) and is deemed to comply with the
maximum concentration values issued by the European Technical Adaptation Committee (TAC)
as shown below:
Substance Proposed Maximum
Concentration Actual Concentration
Lead (Pb) 0.1% < 0.1%
Mercury (Hg) 0.1% < 0.1%
Cadmium (Cd) 0.01% < 0.01%
Hexavalent Chromium (Cr6+) 0.1% < 0.1%
Polybrominated biphenyls (PBB) 0.1% < 0.1%
Polybrominated diphenyl ethers (PBDE) 0.1% < 0.1%
Certain components of products as stated above are exempted under the Annex of the RoHS
Directives as noted below:
Examples of exempted components are:
1. Mercury in compact uorescent lamps not exceeding 5 mg per lamp and in other lamps not
specically mentioned in the Annex of RoHS Directive.
2. Lead in glass of cathode ray tubes, electronic components, uorescent tubes, and electronic
ceramic parts (e.g. piezoelectronic devices).
3. Lead in high temperature type solders (i.e. lead-based alloys containing 85% by weight or
more lead).
4. Lead as an allotting element in steel containing up to 0.35% lead by weight, aluminium
containing up to 0.4% lead by weight and as a cooper alloy containing up to 4% lead by
weight.

ivViewSonic PJ558D
Copyright Information
Copyright © ViewSonic®Corporation, 2007. All rights reserved.
Macintosh and Power Macintosh are registered trademarks of Apple Computer, Inc.
Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of Microsoft
Corporation in the United States and other countries.
ViewSonic, the three birds’ logo, OnView, ViewMatch, and ViewMeter are registered trademarks of
ViewSonic Corporation.
VESA is a registered trademark of the Video Electronics Standards Association. DPMS and DDC are
trademarks of VESA.
PS/2, VGA and XGA are registered trademarks of International Business Machines Corporation.
Disclaimer:ViewSonic Corporation shall not be liable for technical or editorial errors or omissions
contained herein; nor for incidental or consequential damages resulting from furnishing this material,
or the performance or use of this product.
In the interest of continuing product improvement, ViewSonic Corporation reserves the right to change
product specications without notice. Information in this document may change without notice.
No part of this document may be copied, reproduced, or transmitted by any means, for any purpose
without prior written permission from ViewSonic Corporation.
Product Registration
To meet your future needs, and to receive any additional product information as it becomes available,
please register your product on the Internet at: www.viewsonic.com. The ViewSonic Wizard CD-
ROM also provides an opportunity for you to print the registration form, which you may mail or fax to
ViewSonic.
For Your Records
Product Name:
Model Number:
Document Number:
Serial Number:
Purchase Date:
PJ558D
ViewSonic DLP Projector
VS11529
PJ558D-1_UG_ENG Rev. 1C02-27-07
The lamp in this product contains mercury.
Please dispose of in accordance with local, state or federal laws.

English
ViewSonic PJ558D1
Safety Instructions
Read all of these instructions before you operate your projector and save for future
reference.
1. Check that the operating voltage of your unit is identical with the voltage of your
local power supply.
2. Should any liquid or solid object fall into the cabinet, unplug the unit and have it
checked by the qualied personnel before operating it further.
3. Do not attempt to service this product yourself, as opening or removing covers may
damage the components inside and will void your warranty.
4. Do not place this product on an unstable cart, stand, or table. The product may
fall, causing serious damage to the product.
5. Unplug the unit from the wall socket if it is not to be used for several days. To
disconnect the cord, pull it out by the plug. Never pull the cord itself.
6. The wall socket should be near the unit and easily accessible.
7. Do not place the projector where the cord can be stepped on as this may result in
fraying or damage to the lead or the plug. Be alert to tripping hazards.
8. Never look into the projector lens when the lamp is switched on as the bright light
can damage your eyes. Never let children look into the lens when it is on.
9. Do not place your hand or objects near the ventilation holes. The air coming out is
hot.
10. Never open any covers on the projector except the lamp cover. Dangerous electrical
voltages inside the projector can cause severe injury. Except as specically directed
in this User’s Manual, do not attempt to service this product yourself. Refer all
servicing to qualied service personnel.
11. Unplug the projector from the wall socket before cleaning. Use a damp cloth for
cleaning the projector housing. Do not use liquid or aerosol cleaners.
12. Keep the plastic packing materials (from the projector, accessories and optional
parts) out of the reach of children as these bags may result in death by suffocation.
Be particularly careful around the small children.

2ViewSonic PJ558D
13. For ventilation reasons, the fan continues to operate after the projector has been
powered off. Please do not unplug the power cord until the fan stops.
14. The projector is equipped with ventilation holes (intake) and ventilation holes
(exhaust). Do not block or place anything near these slots, or internal heat build-up
may occur, causing picture degradation or damage to the projector.
15. When you replace the projector lamp, never touch the new bulb with your bare
hands. The invisible residue left by the oil on your hands may shorten the bulb life.
Use lint-free gloves or nger cots are recommended.
16. The product should be situated away from heat sources such as radiators, heat
registers, stoves, or other products (including ampliers) that produce heat.
17. Do not overload wall outlets, extension cords, or integral convenience receptacles
as this can result in a risk of re or electric shock.

English
ViewSonic PJ558D3
Notes on AC Power Cord
AC Power Cord must meet requirement of country where you use a projector. Conrm an
AC plug type with graphics below and proper AC Power Cord must be used. If supplied
AC Power Cord does not match your AC outlet, contact your sales dealer.
This projector is equipped with a grounding type AC line plug. Make sure that your
outlet ts the plug. Do not defeat the safety purpose of this grounding type plug. We
highly recommend using a video source device also equipped with a grounding type
AC line plug to prevent from signal interference due to voltage uctuation.

4ViewSonic PJ558D
CONTENTS
Product Introduction .................................................................................................5
Projector Features.............................................................................................5
Package Contents.............................................................................................6
Getting to Know the Projector...................................................................................7
Projector Components.......................................................................................7
Remote Control Components..........................................................................10
Installation ..............................................................................................................11
Connecting the Projector.................................................................................11
Powering On/Off the Projector ........................................................................12
Adjusting the Projected Image ........................................................................13
Adjusting the Projector Zoom and Focus .......................................................14
Adjusting Projection Image Size......................................................................14
Using the Projector.................................................................................................16
Control Panel...................................................................................................16
Remote Control ...............................................................................................17
Battery Replacement.......................................................................................17
Remote Control Operation ..............................................................................18
Menu Options .........................................................................................................19
Color (Computer/Video Mode) ........................................................................20
Image (Computer Mode) .................................................................................22
Image (Video Mode)........................................................................................23
Management (Computer/Video Mode)............................................................24
Audio (Computer/Video Mode)........................................................................25
Language ........................................................................................................26
Maintenance...........................................................................................................27
Cleaning the Lens ...........................................................................................27
Cleaning the Projector Housing.......................................................................27
Replacing the Lamp ........................................................................................28
Specications .........................................................................................................30
Appendix.................................................................................................................31
Indicator Messages .........................................................................................31
Preset Signals .................................................................................................32
Troubleshooting...............................................................................................33

English
ViewSonic PJ558D5
Product Introduction
Projector Features
The projector integrates high-performance optical engine projection and a user-friendly
design to deliver high reliability and ease of use.
The projector offers the following features:
Single chip 0.55” Texas Instruments DLP™ technology
XGA (1024 x 768 pixels)
Compact size, light weight for portability
1.2x manual zoom lens
Auto image re-sizing (Auto-Sync.) to 1024 x 768 full screen with scaling compression
compatibility for VGA, SVGA, XGA and SXGA*.
State-of-the-art motion adaptive hardware deinterlacing with 3:2 pull down
Compatibility with Macintosh®computers
Compatibility with NTSC, PAL, SECAM, and HDTV
Multi-function remote control
D-Sub 15-pin cable for analog video connectivity
User-friendly, multi-language on-screen display (OSD)
Advanced electronic keystone correction
* means compressed.

6ViewSonic PJ558D
Package Contents
When you unpack the projector, make sure you have all these components:
Save the original shipping carton and packing material; they will come in handy
if you ever to ship your unit. For maximum protection, repack your unit as it
was originally packed at the factory.
Accessories and components may vary by retailer and region.
Lithium battery is loaded in the remote control. Remove the transparent
insulation tape by pulling it before use.
Projector with Lens Cap AC Power Cord VGA Cable (D-SUB to D-SUB)
S-Video Cable Composite Video Cable Audio Cable
VGA (D-SUB) to
HDTV (RCA) Cable
Projector
Carrying Case User’s Manual
Remote Control (IR)
with Lithium battery
POWER
MUTE
4:3/16:9 KEYSTONE
LASER
ENTER BLANK
MENU
VOLUME
AUTO SOURCE
Optional Accessory:
Quick Start Guide
RS232 Cable USB Cable

English
ViewSonic PJ558D7
Getting to Know the Projector
Projector Components
Front View
1. Lens cap
2. Lens cap strap
3. Front IR r e mote co n trol
sensor
4. Lens
5. Ventilation holes (intake)
6. Zoom ring
1 2 4
7
8
9
10 5
6
12
11 3
7. Focus ring
8. Control panel
9. Speaker
10. Ventilation holes (exhaust)
11. Elevator foot
12. Elevator button

8ViewSonic PJ558D
Rear View
1. Interface connector
2. Rear IR remote control sensor
3. Security lock receptacle
4. AC power socket
5. Ventilation holes (intake)
6. Tilt-adjustment foot
Bottom View
1. Lamp cover
2. Ceiling mount
1
2
3
4 56 6
2 2
1
2
This projector can be used with a ceiling mount for support. The ceiling mount
is not included in the package.

English
ViewSonic PJ558D9
Control Panel
1. (power)
2. Power LED indicator
3. Keystone /
4. Auto 
5. Menu
6. Four direction buttons
7. Lamp LED indicator
8. Source 
Interface Connector
1. USB connector (Service purpose)
This connector is used for engineering purpose.
2. Audio input connector
Connect an audio output from video equipment to this jack.
3. RS232 connector
When operating the projector via a computer, connect this to the controlling
computer’s RS-232C port.
4. Computer IN (D-SUB) connector (Blue)
Connect image input signal (analog) to this connector.
5. S-Video connector
Connect S-Video output from video equipment to this jack.
6. Computer Out (D-SUB) connector (Black)
Connect to a computer display, etc.
7. Video connector
Connect composite video output from video equipment to this jack.
7
21 3
6
4 5

10ViewSonic PJ558D
Remote Control Components
1. Power button
2. Four direction buttons
3. Menu button
4. Enter button
5. Keystone /buttons
6. Volume /buttons
7. Source button
8. Mute button
9. Blank button
10. 4:3/16:9 button
11. Auto button
POWER
MUTE
4:3/16:9 KEYSTONE
LASER
ENTER BLANK
MENU
VOLUME
AUTO SOURCE
1
2
3
4
7
65
8
9
10
11

English
ViewSonic PJ558D11
Installation
Connecting the Projector
Audio Cable VGA (D-SUB) to HDTV (RCA)
Cable
RS232 Cable Video Cable
VGA Cable (D-SUB to D-SUB) S-Video Cable
Desktop type Laptop type
23
6
1
1
3
54
When connecting cable, power cords of both a projector and external
equipment should be disconnected from AC outlet.
 The gure above is a sample connection. This does not mean that all of
these devices can or must be connected simultaneously.

12ViewSonic PJ558D
Powering On/Off the Projector
Powering On the Projector:
1. Remove the projector lens cap.
2. Complete the AC power cord and peripheral signal cable(s) connections.
3. Press the button on the Projector Control Panel or the button on the Remote
Control to turn on the power.
4. Turn on your source (computer, notebook, DVD, etc.). The projector automatically
detects your source.
If the “Searching for source” message appears on the screen, ensure that
the appropriate signal cable(s) are securely connected.
If you are connecting multiple sources to the projector simultaneously, press
the Source button either on the Projector Control Panel or the Remote Control.
Warning:
Never look into the lens when the lamp is on. This can damage your eyes. It is
especially important that children are not allowed to look into the lens.
Powering Off the Projector:
1. Press the button on the Projector Control Panel or the button on the Remote
Control. A message will appear on the screen:
2. Press the button on the Projector Control Panel or the button on the Remote
Control again to turn off the power. Wait until the lamp LED indicator turns off.
Please wait until the fan motor and the lamp LED turn off before removing
the AC power cord from the projector.

English
ViewSonic PJ558D13
Adjusting the Projected Image
Adjusting the Projector Height
The projector is equipped with an elevator foot to adjust the image height.
To raise or lower the image:
1. Turn the projector over and locate the elevator foot. Press the elevator button to
extend the foot so it may be adjusted.
2. While holding down the elevator button, adjust the foot to the desired height, then
release the button to lock the elevator foot into position.
3. Use tilt-adjustment foot to ne-tune tilt-adjustment.
4. Lower the projector so it rests on its foot; adjust as needed.
To avoid damaging the projector, make sure that the elevator foot and tilt-
adjustment foot are fully retracted before placing the projector in its carrying
case.
1
2
3

14ViewSonic PJ558D
Adjusting the Projector Zoom and Focus
1. Adjust the image size by rotating the zoom ring.
Rotate to the right to reduce the image.
Rotate to the left to enlarge the image.
2. Focus the image by rotating the focus ring.
A still image is recommended for focusing.
Adjusting Projection Image Size
Refer to the graphic and table below to determine the screen size and projection
distance.
Zoom Ring
Focus Ring
Distance between the screen
and the center of the lens

English
ViewSonic PJ558D15
Position the projector in a horizontal position; other positions can cause heat
build-up and damage to the projector.
Make sure the heat ventilation holes are not blocked.
Do not use the projector in a smoky environment. Smoke residue may cause
buildup on critical parts (i.e. DMD, lens assembly, etc.)
PROJECTION
DISTANCE (METER)
4:3 SCREEN
SIZE-
DIAGONAL
(INCH)
Wide
Tele
1.0
27.50
25.60
2.1
57.70
53.70
3.0
82.40
76.50
5.0
137.4
128.0
10.0
275.00
256.00
* This table is for user reference only.