ViewSonic PS600W User manual

1
Remote control
To use the remote mouse control keys (Page Up, Page Down), see "Using the remote
PgUp/PgDn function" on page 3 for details.
•On/Off
Toggles the projector between standby
mode and Power ON.
•COMP
Selects source from COMPUTER
port for display.
•HDMI
Selects source from HDMI port for
display.
•HDMI1
Selects source from HDMI 1 port for
display.
•HDMI2
Selects source from HDMI 2 port for
display.
•VIDEO
Selects source from VIDEO or S-
VIDEO port for display.
• Auto Sync
Automatically determines the best
picture timings for the displayed
image.
• Source
Displays the source selection bar.
• / / / (Keystone keys)
Manually corrects distorted images
resulting from an angled projection.
•Enter
Enacts the selected On-Screen Display
(OSD) menu item.
PS501W/PS501X/PS500XPS600W/PS600X

2
Remote control code
The projector can be assigned to 8 different remote control codes, 1 to 8. When several
adjacent projectors are in operation at the same time, switching the remote control codes
can prevent interference from other remote controls. Set the remote control code for the
projector first before changing that for the remote control.
To switch the code for the projector, select from among 1 to 8 in the SYSTEM > Remote
Control Code menu.
To switch the code for the remote control, press ID set and the number button
corresponding to the remote control code set in the projector OSD together for 5 seconds or
more. The initial code is set to 1. When the code is switched to 8, the remote control can
control every projector.
•
Displays the Corner Adj. page.
• Left/ Right/ Up/ Down
Selects the desired menu items and makes
adjustments.
•Menu
Turns on the On-Screen Display (OSD)
menu.
•Exit
Exits and saves menu settings.
• (Laser)
Emits visible laser pointer light for
presentation purposes.
• Aspect
Displays the aspect ratio selection bar.
• Freeze
Freezes the screen picture.
• Pattern
Displays embedded test pattern.
•Blank
Hides the screen picture.
• PgUp (Page Up)/PgDn (Page Down)
Operates your display software program
(on a connected PC or USB reader) which
responds to page up/down commands (like
Microsoft PowerPoint).
Only available when a PC input or USB
Reader signal is selected.
• (Presentation Timer)
Displays the presentation timer settings
menu.
•EcoMode
Displays the lamp mode selection bar.
• (VolumeUp)
Increases the volume level.
• (Volume Down)
Decreases the volume level.
• (Mute)
Toggles the projector audio between on
and off.
• (Information)
Displays the INFORMATION menu.
• (Zoom In)
Magnifies the projected picture size.
• (Zoom Out)
Reduces the projected picture size.
•ColorMode
Displays the color mode selection bar.
• Network
Displays the LAN Control Settings
menu.

3
If different codes are set on the projector and remote control, there will be no response from
the remote control. When that happens, a message will display to remind you to switch the
code for the remote control.
Using the remote PgUp/PgDn function
The capability of operating your computer with the remote control gives you more
flexibility when delivering presentations.
1. Set the input signal to a PC signal.
2. Connect the projector to your PC or notebook with a USB cable prior to using the
remote control in place of your computer’s mouse.
3. To operate your display software program (on a connected PC) which responds to
page up/down commands (like Microsoft PowerPoint), press PgUp/PgDn.
Remote control effective range
Refer to the illustration about the location of the Infra-
Red (IR) remote control sensor(s). The remote control
must be held at an angle within 30 degrees
perpendicular to the projector's IR remote control
sensor(s) to function correctly. The distance between
the remote control and the sensor(s) should not exceed
8 meters (~ 26 feet).
Make sure that there are no obstacles between the
remote control and the IR sensor(s) on the projector
that might obstruct the infra-red beam.
Replacing the remote control batteries
1. To open the battery cover, turn the remote control over to view its back, press on the
finger grip on the cover and slide it down in the direction of the arrow as illustrated.
2. Remove any existing batteries (if necessary) and install two AAA batteries observing
the battery polarities as indicated in the base of the battery compartment. Positive (+)
goes to positive and negative (-) goes to negative.
3. Refit the cover by aligning it with the base and pushing it back down into position.
Stop when it clicks into place.
WARNING
• Avoid leaving the remote control and batteries in an excessive heat or humid environment
like the kitchen, bathroom, sauna, sunroom or in a closed car.
• Replace only with the same or equivalent type recommended by the battery manufacturer.
Approx.30°