ViewZ 40" WUXGA User manual

46 & 55-INCH WUXGA
SUPER NARROW BEZEL
TFT-LCD MONITOR
INSTRUCTION MANUAL
Please read this manual thoroughly before use, and keep it handy for future reference.

SAFETY INSTRUCTION ………………………………………………………….…… 2 ~ 3
CAUTIONS …………………………………………………………….......................... 4
FCC RF INTERFERENCE STATEMENT ……………………………....................... 5
CONNECTING WITH EXTERNAL EQUIPMENT …………………………………… 6
REMOTE FUNCTIONS ………………………………………………………………… 7
CONTROLS AND FUNCTIONS ……………………………………………………….. 8 ~ 13
EXTENTENSIONAL IR RECEIVER FOR REMOTE CONTROLLER ..……………. 14
MOUNTING GUIDE …………………………………………………………………….. 15
D-SUB CONNECTOR PIN ASSIGNMENTS ………………………………………… 16
POWER MANAGEMENT ……………………………………………………………… 17
SPECIFICATIONS ……………………………………………………………………… 18
TROUBLE SHOOTING GUIDE …………………………………………………......... 19
INSTRUCTION MANUAL ………………………………………………………………………. 1
This Monitor was
Manufactured by ISO 9001
Certified Factory

Important Safety Instruction
1. Read these instructions.
2. Keep these Instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as radiators, heat registers,stoves, or other
apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug.
Apolarized plug has two blades with one wider than the other.
Agrounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety.
If the provided plug does not fit into your outlet, consult an electrician for replacement
of the bsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles and the point where they exit from the apparatus.
11. Only use attachment/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket or table specified by the manufacturer or
sold with the apparatus. When a cart is used, use caution when moving
the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused
for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus the apparatus has been exposed to
rain or moisture does not operate normally or has been dropped.
2 ………………………………………………………………………. INSTRUCTION MANUAL

- The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids,
such as vases, shall be placed no the apparatus.
- Minimum distances(e.g. 10cm) around the apparatus for sufficient ventilation.
“WARNING – To reduce the risk of fire or electric shock, do not expose the apparatus to rain or moisture.”
“The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids,
such as vases, shall be placed on the apparatus.”
This symbol is intended to alert the user to the presence of uninsulated :
dangerous voltage with in the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
This symbol is intended to alert the user to the presence of important operating
and maintenance(servicing) instructions in the literature accompanying the
appliance.
INSTRUCTION MANUAL ………………………………………………………………………. 3

CAUTION
The power supply cord is used as the main disconnect device, ensure that the socket-outlet is
located/installed near the equipment and is easily accessible.
ATTENTIONN
Le cordon d`alimentation est utillsé comme interrupteur général. La prise de courant doit être
située ou installée à proximité du matériel et être facile d`accès
NEVER REMOVE THE BACK COVER▶
Removal of the back cover should be carried out only by qualified personnel.
DO NOT USE IN HOSTILE ENVIRONMENTS▶
To prevent shock or fire hazard, do not expose the unit to rain or moisture.
This unit is designed to be used in the office or home. Do not subject the unit to vibrations,
dust of corrosive gases.
KEEP IN A WELL VENTILATED PLACE▶
Ventilation holes are provided on the cabinet to prevent the temperature from rising.
Do not cover the unit or place anything on the top of unit.
AVOID HEAT▶
Avoid placing the unit in direct sunshine or near a heating appliance.
TO ELIMINATE EYE FATIGUE▶
Do not use the unit against a bright back ground and where sunlight or other light sources will
shine directly on the monitor.
BE CARE▶FUL OF HEAVY OBJECT
Neither the monitor itself nor any other heavy object should rest on the power cord.
Damage to a power cord can cause fire or electrical shock.
4 ………………………………………………………………………. INSTRUCTION MANUAL

NOTE
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television reception which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures.
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio, TV technician for help.
- Only shielded interface cable should be used.
Finally, any changes or modifications to the equipment by the user not expressly approved by
the grantee or manufacturer could void the users authority to operate such equipment.
▶DOC COMPLIANCE NOTICE
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital
apparatus set out in the radio interference regulation of Canadian Department of
communications.
INSTRUCTION MANUAL ………………………………………………………………………. 5

A. BACK PANEL CONTROL
1. DISPLAY PORT(OPTIONAL)
2. HDMI IN.
3. DVI.
4. VGA.
5. UPGRADE PORT
6. PC STEREO IN
7. PC STEREO OUT.
8. RJ-45.
9. RS-232C IN(OPTIONAL)
10. RS-232C OUT(OPTIONAL)
11. AC IN.
※PC cable
To use the “Model ID” function using RS-232 cable, the pin 4 in the PC cable must be deleted.
6 ………………………………………………………………………. INSTRUCTION MANUAL

B. REMOTE CONTROLLER(Optional)
1. POWER( )
Turns the power ON or OFF. There will be a few seconds delay before the display appears.
2. SOURCE
Selects an input source.
3. AUTO
Auto geometry adjustment in the RGB PC source.
4. MUTE
Mutes the sound.
5. MENU
Activates and exits the On Screen Display.
6. EXIT
Exits the On Screen Display.
7. VOL(◀& ▶)
Increases or decreases the level of audio volume.
8. UP/DOWN
Moves upwards or downwards in the OSD menu.
9. ENTER
Enters an OSD submenu or accepts your selection.
INSTRUCTION MANUAL ………………………………………………………………………. 7

C. RIGHT SIDE BUTTON CONTROL
1 & 2. VOL(+) & VOL(-)
Adjust the volume and menu settings.
3 & 4. ▲& ▼
These buttons allow user to enter the sub-menu of the activated function.
The up(▲) button is HOLD function and Auto switching
functions.
5. SOURCE/SELECT
Selects an input source.
Enters a submenu or accepts your selection in the OSD menu.
6. MENU/EXIT
Activates and exits the On Screen Display.
This button can also be used to move previous menu or status.
7. POWER ON/OFF( / I )
Turns the power ON or OFF. There will be a few seconds delay
before the display appears.
8. POWER LED
The power LED lights with green when the power is turned ON.
The power is turned off by pressing the power button again,
and the power LED goes Red.
9. IR Sensor
Remote controller sensor.
8 ………………………………………………………………………. INSTRUCTION MANUAL
1
2
3
4
5
6
7
8
9

On-screen Display Menus
There are four (4) on-screen menus that allow you to your settings. Press the Menu button to access the OSD menu.
Icon Menu Function
Image Adjusts the Brightness, Contrast, Color Temperature,
Zoom, and Information Bar settings
Display Adjusts the Auto adjust, Phase, Clock, Display position
and Auto color settings. (PC mode.)
Misc Adjusts the Volume ,Mute ,input, osd setting and language
Settings.
System Resets the factory default settings and adjusts the
Image Rotation, Key lock, Model ID, Control Mode settings.
A. Image Menu
To access the Image menu, press the Menu button on the front panel of the monitor, then press the Up
and Down arrow buttons to select the Image icon. Press the Left arrow button to enter the menu, and
then press the Up and Down arrow buttons to select a submenu. When finished, press the Menu button
to save any changes, then press the Menu button again to exit the OSD.
Submenu Definition
Brightness Adjusts the brightness level for video performance (range 0-100).
Contrast Adjusts the intensity of the image (range 0-100).
Color Temp Adjusts the color of the picture Choices are Warm, Normal, Cool, and User
(Red , Green, and Blue).
Zoom Sets the aspect ration for the monitor. Choices are 16:9 and 4:3.
INSTRUCTION MANUAL ………………………………………………………………………. 9

B. Display Menu
To access the Display menu, press the Menu button on the front panel of the monitor, then press the Up
and Down arrow buttons to select the Display icon. Press the Left arrow button to enter the menu, and
then press the Up and Down arrow buttons to select a submenu. When finished, press the Menu button
to save any changes, then press the Menu button again to exit the OSD.
Submenu Definition
Auto Adjust Automatic adjustment of the screen geometry.
Phase Adjusts the number of horizontal picture elements (range 0-100).
Clock Adjusts the vertical noise of screen image (range 0-100).
Display Position Moves the horizontal and vertical position of the picture.
Auto Color Adjusts the automatic color balance.
10 ………………………………………………………………………. INSTRUCTION MANUAL

C. Sound Menu
To access the Sound menu, press the Menu button on the control panel of the monitor, then
press the UP and Down arrow buttons to select the Sound icon. Press the Left arrow button to
enter the menu, and then press the Up and Down arrow buttons to select a submenu. When
finished, press the Menu button to save any changes, then press the Menu button again to exit
the OSD.
S u bmenu D efinition
Volume Controls the built-in speaker volume (range 0-100).
Mute Enables/disables
audio. Choices are: On and Off.
Input
Selects the video input source. Choices are VGA,HDMI, and DVI
Osd Settings Adjusts the number of horizontal picture elements.
Choices are Timer (3sec, 6sec, 12sec), Rotation (0°, 90°, 180°, 270°),
Position and Transparancy (range 0-100).
Language Adjusts the language of the OSD.
Choices are: English, French, Spanish, Dutch, German, Italian,
Portuguese, Polish, Simplified Chinese and Russian.
INSTRUCTION MANUAL ………………………………………………………………………. 11

D. System Menu
To access the Sound menu, press the Menu button on the control panel of the monitor, then
press the UP and Down arrow buttons to select the Sound icon. Press the Left arrow button to
enter the menu, and then press the Up and Down arrow buttons to select a submenu. When
finished, press the Menu button to save any changes, then press the Menu button again to exit
the OSD.
S u bmenu D efinition
Image Rotation Activates the image Rotation function. The function slightly moves the
displayed image to prevent image persistence
Key Lock Enables or disables the Key Lock function.
Model ID See below.( 0 ~ 100, ALL)
Control Mode Select RJ45
Reset Restores default settings.
12 ………………………………………………………………………. INSTRUCTION MANUAL

E. Monitor Control
1) TCP/IP MODE - Please select “TCP/IP”
- Click the “IP Installer”
- Click the “Update” in IP Installer window
- Find Monitor(s) and if you click the “Model Search” button,
it shows Model ID in the list
- If you click the “Start” button, you can reach the CMS menu .
- Please tick the control Model list(s)
- If you click the “READ” button, it will take monitor
Information checked in IP Installer window.
- And then, you can select the “Model ID” you checked in IP
Installer window.
- Now you can control each button in each Tab in order to
control the monitor(s)
- If you select ”ALL” in the model ID tab, you can control Monitor(s) without Monitor’s ID number.
e.g.) In this case, you can control the “Model ID No. 0” monitor. Defalt is “ALL”
※For the detail explanation, refer to the enclosed “Monitor Control” CD.
NSTRUCTION MANUAL ………………………………………………………………………. 13

- You can connect extensional IR receiver to the place you want using the stereo cable.
- You can attach extensional IR receiver magnetic-designed to the monitor.
14 ………………………………………………………………………. INSTRUCTION MANUAL

Wall mounting (Optional)
The LCD monitors are suitable for VESAstandard wall mount (not included in the delivery).
1. 46-inch: VESA 600mm x 100mm x 100mm x 100mm.
2. 55-inch: VESA 600mm x 200mm x 200mm.
※Attention!
- 46inch :
You must use eight M8x12 screws to assemble this monitor and the wall mount bracket.
- 55inch :
You must use six M8x12 screws to assemble this monitor and the wall mount bracket.
15 ………………………………………………………………………. INSTRUCTION MANUAL
M8x12 screws
< 46 inch >
M8x12 screws
< 55 inch >

▶ PIN ASSIGNMENTS
Pin 1 RED VIDEO 9
2 GREEN VIDEO 10 SIGNAL CABLE DETECT
3 BLUE VIDEO 11 GROUND
4 12 SDA(for DDC)
5 GROUND 13 H-SYNC.(or H+V SYNC.)
6 RED GROUND 14 V-SYNC.
7 GREEN GROUND 15 SCL(for DDC)
8 BLUE GROUND
D-SUB
▶ ACCESSORIES
1. Power cord In. (Out cable is Option)
2. User’s manual.
3. RS-232 cable (9pin male to female: direct connection).- Option
4. Monitor Control Software CD.
5. Extensional Remote Controller Receiver cable; Stereo cable.
6. Remote controller & Batteries.
7. Wall mount bracket (Optional).
※PC cable
To use the “Model ID” function using RS-232 cable, the pin 4 in the PC cable must be deleted.
INSTRUCTION MANUAL ………………………………………………………………………. 16

This monitor features a power management system to “power down” upon receipt of the VESA
DPMS(The display power management signaling) from a VESA DPMS video card.
The VESA DPMS-compliant video card performs this signaling system through not sending
horizontal, vertical, or sync signal.
This monitor enters an appropriate mode through identifying each of the three modes of the
signaling system.
POWER CONSUMPTION
46” 55”
240W 330W
LED INDICATOR
The power management feature of the monitor is comprised of four stages: On(Green),
Standby, Suspend, Active off(Red on/off 1 sec) and Unsupported mode(Green).
MODE LED COLOR MONITOR OPERATION
ON GREEN Normal Operation
POWER OFF RED Not Operation
17 ………………………………………………………………………. INSTRUCTION MANUAL

46’’ WUXGA 55’’ WUXGA
LCD-
Type
TYPE 46˝Diagonal AM-TFT
(Active-Matrix)
55˝Diagonal AM-TFT
(Active-Matrix)
PIXELl PITCH(mm) 0.53025(H) x 0.53025(V) 0.63(H) x 0.63(V)
BRIGHTNESS 500cd/m²(Typical)
CONTRAST RATIO 3500:1 (Typical) 5000:1(Typical)
VIEWING ANGLE 178°/178°(H/V)
RESPONSE TIME 8msec (G-to-G)
RESOLUTION (H x V) 1920X1080 @60Hz
FREQUENCY HORIZONTAL: 31~80KHz / VERTICAL: 56~75Hz
INPUT
SIGNAL
DISPLAY PORT(OPTIONAL)
HDMI
DVI
VGA
UPGRADE PORT
PC STEREO IN/OUT
RJ-45
RS-232C IN/OUT(OPTIONAL)
AC IN
ACTIVE DISPLAY AREA
(H x V) 1018.08mm X 572.67mm 1209.6mm X 684.0mm
PACKING DIMENSIONS
(W x H x D)
1340mm X 920mm X 430mm
(52.76’’ X 36.22” X 16.93”)
1340mm X 920mm X 430mm
(52.76’’ X 36.22” X 16.93”)
WEIGHT Net Weight 33 kg (73 lbs) 45kg (99 lbs)
Gross Weight 43kg (95 lbs) 60.0kg (133 lbs)
ELECTRICAL
RATINGS 100-240V~, 50/60Hz (Auto Switching)
▶▶ NOTE: Technical specifications are subject to change without notice.
INSTRUCTION MANUAL ………………………………………………………………………. 18