Vigitron MaxiiCooper Vi3202 User manual

Ethernet Extenders
Vi3202 24VDC/VAC Coax Ethernet Extender w/60W PoE Manual
DO NOT OPEN
RISK OF ELECTRIC SHOCK
CAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK,
DO NOT REMOVE COVER. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
IP Camera-end Installation
The Smart Choice for Transmission Solutions www.vigitron.com
Important Safety Warning
- Connect the IP camera RJ45 connector to the 10/100BaseT Ethernet port
of Vi3202 using a standard Cat5/6 cable of maximum 100 m in length.
- Connect one end of the long coax cable to the BNC connector of
Vi3202.
- Connect a 24VDC or 24VAC power supply, at least 74W, to the Vi3202
power connector. The power input is a non polarized 2-pin terminal block.
The Power LED, PoE LED and link LED on the 10/100 connector should be
“ON” to indicate proper connection between the camera and Vi3202.
Ethernet Switch/NVR-end Installation
- Read these instructions.
- Keep these instructions.
- Heed all warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Clean only with a dry cloth.
- Install in accordance with the manufacturer’s instructions.
- This installation should be made by a qualified service person and should
conform to all local codes.
- DO NOT bundle UTP or Coax signals in the same conduit as high-voltage
wiring.
- To reduce the risk of fire or electrical shock, do not expose these products
to rain, moisture, dripping or splashing.
- No objects filled with liquids, such as vases, shall be placed on Vigitron
equipment.
- DO NOT install the unit in a place where the operating ambient tempera
ture exceeds 65°C.
- Make sure that the external power supply output voltage is in the recom
mended range.
- Do not install near any heat sources such as radiators, heat registers,
stoves or other apparatus that produce heat.
- Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
- Only use attachments/accessories specified by the manufacturer.
- Unplug this apparatus during lightning storms or when unused for long
periods of time.
- Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as a power
supply cord or plug is damaged, liquid has been spilled, or objects have
fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
- The mains plug is used as the disconnect device and shall remain readily
operable.
WARNING! - To reduce the risk of fire or electric shock, do not expose
this apparatus to rain or moisture. This apparatus shall not be exposed to
dripping or splashing and no objects filled with liquids, such as vases shall
be placed on the apparatus.
WARNING! - This apparatus is a Class I product. This product must
be connected to a mains socket outlet thru an AC to DC Power supply.
WARNING! - The mains plug is used as the disconnect device and
shall remain readily operable.
The Vi3202 is the perfect solution for replacing existing analog PTZ
cameras with advanced IP PTZ cameras. It uses existing Coax cable for
transmitting IP video up to 5000 feet (1,515 m) and the existing 24VDC or
24VAC power supply as power input to provide up to 60W PoE to the
cameras. Using the existing Coax cable and power supply provides great
time and cost saving.
Its unique Symmetric Bandwidth (SBW™) assures full bandwidth transmis-
sion is maintained over the entire operational distance for both uploads and
downloads with Virtual Zero Packet Loss (VZPL™). Type tested under
NEMA-TS2 environmental standards for extended temperature operations
between -20C° to +65C°. The Vi3202 is MegaPixel Certified (MPC™), type
tested to network packet performance standards, and major manufacturer
compatibility tested to assure you error free and reliable operations.
Its compact design allows to be installed in many weatherproof and security
houses or many types of camera mounts to further reduce installation costs.
Installation cost savings, proven performance, and major camera brand
compatibility all go into making Vigitron’s MaxiiCopper™ Vi3202 an ideal
solution for extended distance data and power transmission.
- Use a Vi24xxA on the receiving side.
- If using a Vi2401A set the Master/Slave dip switch to “Slave” mode and
Set the Remote/Local switch to Local.
- Connect a qualified 12VDC power supply to the Vi24xxA.
- Connect the RJ45 connector of the Ethernet switch to the 10/100BaseT
Ethernet port of Vi2401A using a standard Cat5/6 cable of maximum
100 m in length.
- Connect one end of the long coax cable to the BNC connector of Vi24xxA.
The link LED on the 10/100 Ethernet connector should be “ON” to indicate
proper connection between the switch and Vi24xxA. Also the Traffic LED
on the Coax side should be on and flashing to indicate proper connection.
While the Link LED, Orange for 100BaseT and Green for 10BaseT, in a
steady state will indicate confirmed connection between extenders.
UMVi3202_0821
Vi3202
Cat5/6
Data + 60W
24VDC or 24VAC From
Existing Analog Installation
60W PTZ
High Powered Camera
up to 5,000 ft. Coax
Ethernet Switch/NVR-end Installation
Cat5/6
Data
Network Switch

Limited Lifetime Warranty
Vigitron, Inc. warrants that all Vigitron products (“Product”), if used in accordance
with these instructions, will be free of defects in material and workmanship for
lifetime defined as the duration period of time until product end of life is announce-
ment. After which Vigitron will continue to provide warranty services for a period of 3
years. Period covering valid warranty will be determined by proof of purchase in the
form of an invoice from an authorized Vigitron dealer.
Warranty will only be provided for as long as the original end user purchaser owns
the product. Warranty is not transferrable. At Vigitron's option, defective product will
be repaired, replaced or substituted with a product of equal value. This warranty
does not apply if, in the judgment of Vigitron, Inc., the Product fails due to damage
from shipment, handling, storage, accident, abuse or misuse, or if it has been used
or maintained not conforming to Product manual instructions, has been modified, or
serial number removed or defaced. Repair by anyone other than Vigitron, Inc. or an
approved agent will void this warranty. Vigitron, Inc. shall not under any circum-
stances be liable to any person for any incidental, indirect or consequential
damages, including damages resulting from use or malfunction of the product, loss
of profits or revenues or costs of replacement goods. The maximum liability of
Vigitron, Inc. under this warranty is limited to the original purchase price of the
Product only.
Technical Specifications*
Ordering Information
Status LEDs
© Copyright 2016 Vigitron, Inc.
TEL (+1) 858 - 484 - 5209 • FAX (+1) 858 - 484 - 1205
7810 Trade Street, Suite 100, San Diego, CA 92121, USA • [email protected] • www.vigitron.com
UMVi3202_0821
Data and PoE Distance**
LED Name Color Status Function
OFF Power is OFF
ON Power is ON
OFF No Traffic
FLASHING Traffic
GREEN ON Connection is OK, 10BaseT Mode
ORANGE ON Connection is OK, 100BaseT Mode
OFF No connection
FLASHING Connection is OK with Traffic
OFF No connection
ON Connection is OK
Link
(Standard Side)
Power GREEN
Traffic
(Extended Side)
YELLOW
10/100 BaseT
(Extended Side)
Traffic
(Standard Side) GREEN
YELLOW
PoE GREEN OFF
ON PoE Power is On
PoE Power is Off
Drawings
Side View
Left View
10BaseT
100BaseT
5,000 ft./1,524 m
DistanceData Rate
*Specifications subject to change without notice.
**Distance figures are based on RG59 coax cables using in house testing mirroring typical
installations. Factors such as cabling, connections, use of power and environmental conditions
may affect actual distances and should be taken into consideration.
1,800 ft./548 m
Right View
Electrical
Ethernet Interface Standard 10/100BaseT
Data Rate Auto select 10/100 Mb/s
Full speed / full duplex at maximum rated distance
Coax 75 Ohm, 5,000 feet (1,524 m) at 10BaseT
1,800 feet (548 m) at 100BaseT
PoE Output Power 60W @ 54 VDC
Input Power 24VDC, 24VAC, Maximum 3.2A
Status LEDs Power On
PoE
Standard Ethernet: Traffic, Link
Extended Ethernet: Traffic, 10/100BaseT
Connectors Ethernet Interface: Shielded RJ-45 Connector
Extended Interface: Female BNC
Power: Pluggable 2-pin connector (non-polarized)
RFC 2544 TCP/IP Packet Transmission
PoE Compatibility IEEE 802.3af , IEEE 802.3at, 60W PoE
RFC 768 UDP, 2068 HTTP, 793 TCP
791 IP, 1783 TFTP, 894 IP over Ethernet
Jumbo Frame Yes
Support
Regulatory
Safety CE
Environmental RoHS, WEEE
Mechanical
Dimensions 5.62 x 3.45 x 1.9 in., 14.27 x 8.76 x 4.83 cm (HxWxL)
Weight 1.11 lb, 503 g
Material Extruded Aluminum
Environmental
Humidity 0 to 95%, non-condensing
Temperature Operating: -20°C to +65°C per NEMA-TS2 testing
Storage: -40°C to +85°C
*Specifications subject to change without notice.
PART No. Description
Vi2401A Single port Coax Ethernet Extender
Vi2404A 4-port Coax Ethernet Extender
Vi2408A 8-port Coax Ethernet Extender, 19”, 1U
Vi2416A 16-port Coax Ethernet Extender, 19”, 1U
Vi3202 24 VDC/VAC 60W PoE Coax Extender
10/100 BaseT
Extended
Ethernet
10/100
Traffic
Traffic
Power
Link
PoE
5.62"
14.27 cm
1.9"
4.83 cm
3.45"
8.76 cm
10/100 BaseT
Extended
Ethernet
10/100
Traffic
Traffic
Power
Link
PoE
Coax Ethernet Extender w/ 60W PoE
Vi3202