Vigitron OmniiCopper Vi27000 Series User manual

Application Drawing
Vi27000/Vi27001 Single-Pair Ethernet & PoE Transmission Solution Installation Manual
DO NOT OPEN
RISK OF ELECTRIC SHOCK
CAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK,
DO NOT REMOVE COVER. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
IP Camera-end Installation
The Smart Choice for Transmission Solutions www.vigitron.com
Important Safety Warning
- Install the Vi27000 “Remote Unit” near the Camera end.
- Connect the IP camera RJ45 connector to the 10/100BaseT Ethernet Port of
Vi27000 using a standard Cat5/6 cable of maximum 100 m .
- Connect one end of the long Single Pair Wire to the 2-pin Terminal block of
Vi27000. Make sure the Single Pair Wire polarity matches on the Vi27001 End.
The link LED on the 10/100 connector should be “ON” to indicate proper connection
between the camera and Vi27000.
The PoE LED on the 10/100 connector should be "ON" when PoE is used to power
up the camera. The Status LED on the Single Pair Wire side should be “ON” and
flashing to indicate proper connection.
Ethernet Switch-end Installation
- Install the Vi27001 “Local Unit” near the network switch.
- Connect the RJ45 connector of the Ethernet switch to the 10/100BaseT Ethernet
port of Vi27001 using a standard Cat5/6 cable of maximum 100 m.
- Connect one end of the long Single Pair Wire to the to the 2-pin Terminal block of
Vi27001. Make sure the Single Pair Wire polarity matches on the Vi27000 End.
The link LED on the 10/100 Ethernet connector should be “ON” to indicate proper
connection between the switch and Vi27001. Also the Status LED on the Single Pair
Wire side should be “ON” and flashing to indicate proper connection.
-If the Vi27001 receives power using PoE, make certain the power adaptor is not
connected. The Vi27000 and camera will receive power from the PSE source.
-If a PSE source such as a PoE network switch is not available, external power
must be provided to the Vi27001.
CAUTION:
If an external power supply adaptor is plugged into Vi27000 or Vi27001, the unit will
not use or pass thru PoE power from the PoE switch. It will use the power from the
plugged in DC power supply.
- Read these instructions.
- Keep these instructions.
- Heed all warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Clean only with a dry cloth.
- Install in accordance with the manufacturer’s instructions.
- This installation should be made by a qualified service person and should conform
to all local codes.
- DO NOT bundle low-voltage signals in the same conduit as high-voltage wiring.
- To reduce the risk of fire or electrical shock, do not expose these products to rain,
moisture, dripping or splashing.
- No objects filled with liquids, such as vases, shall be placed on Vigitron equipment.
- DO NOT install the unit in a place where the operating ambient temperature
exceeds 65° C.
- Make sure that the external power supply output voltage is in the recommended range.
- Do not install near any heat sources such as radiators, heat registers, stoves or
other apparatus (including DVRs) that produce heat.
- Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
- Only use attachments/accessories specified by the manufacturer.
- Unplug this apparatus during lightning storms or when unused for long periods of time.
- Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as a power supply cord or plug is
damaged, liquid has been spilled, or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.
- The mains plug is used as the disconnect device and shall remain readily operable.
Ethernet Extenders
TM
The OmniiCopper™ Vi27000 Series is a revolutionary data transmission
solution that extends full-duplex High-Speed Ethernet and PoE over
Single-Pair Wire infrastructures. The Vi27000 is a transmitter that operates in
conjunction with 1-Port Vi27001 or 4-Port Vi27004 Receivers over virtually any
2 conductor wires reliably. The Vi2700X’s unique transmission technology
eliminates the potential for cross talk,resulting in the perfect solution for
bundled cable runs that are used in many elevatorsand building
communication systems.
Up to 36W power can be provided from a PoE source or a DC power supply at
the Vi27001 (Rx) to the control side,eliminating the need for a local power
supply at the camera location. The Vi27000 Series operatesat the extended
temperature range -30°C to +65°C.
Installation cost savings, tested and proven design and performance go into
making the Vi27000 Series as the perfect solution for building CCTV wiring.
WARNING! - To reduce the risk of fire or electric shock, do not expose this
apparatus to rain or moisture. This apparatus shall not be exposed to dripping or
splashing and no objects filled with liquids, such as vases shall be placed on the
apparatus.
WARNING! - This apparatus is a Class I product. This product must be
connected to a mains socket outlet thru an AC to DC Power supply.
WARNING! - The mains plug is used as the disconnect device and shall
remain readily operable.
The Vi27001 receiver can use a local power supply to power Vi27000 transmitter and the IP camera using PoE.
Data + PoE
Data
Single Pair
Cat5/6
Data + PoE
Cat5/6
Network Switch
PoE Camera
Vi27000
Vi27001
Vi1120
Both the Vi27001 and the Vi27000 can use local power supplies to power themselves and provide PoE to the IP camera .
Data
Data
Single Pair
Cat5/6
Data + PoE
Cat5/6
Network Switch
PoE Camera
Vi27000
Vi27001
Vi0017 Vi1120/Vi001
PoE Switch
The Vi27000 series and a IP camera can be powered by a PoE switch.
PoE Camera
Vi27000Vi27001 Data + PoE
Data + PoE
Single Pair
Cat5/6
Data + PoE
Cat5/6

PART No.
Description
Vi27000 1-Port Single-Pair Wire Ethernet & PoE Extender, Remote Unit
Vi27001 1-Port Single-Pair Ethernet & PoE Extender, Local Unit
Vi27004 4-Port Single-Pair Ethernet & PoE Extender, Local Unit
Limited Lifetime Warranty
Vigitron, Inc. warrants that all Vigitron products (“Product”), if used in accordance with these
instructions, will be free of defects in material and workmanship for lifetime defined as the
duration period of time until product end of life is announcement. After which Vigitron will
continue to provide warranty services for a period of 3 years. Period covering valid warranty will
be determined by proof of purchase in the form of an invoice from an authorized Vigitron dealer.
Warranty will only be provided for as long as the original end user purchaser owns the product.
Warranty is not transferrable. At Vigitron's option, defective product will be repaired, replaced or
substituted with a product of equal value. This warranty does not apply if, in the judgment of
Vigitron, Inc., the Product fails due to damage from shipment, handling, storage, accident, abuse
or misuse, or if it has been used or maintained not conforming to Product manual instructions,
has been modified, or serial number removed or defaced. Repair by anyone other than Vigitron,
Inc. or an approved agent will void this warranty. Vigitron, Inc. shall not under any circumstances
be liable to any person for any incidental, indirect or consequential damages, including damages
resulting from use or malfunction of the product, loss of profits or revenues or costs of
replacement goods. The maximum liability of Vigitron, Inc. under this warranty is limited to the
original purchase price of the Product only.
Technical Specifications*
RoHS
Drawings
Ordering Information
Ethernet Status LEDs
Data/PoE Distance***
© Copyright 2020 Vigitron, Inc.
TEL (+1) 858 - 484 - 5209 • FAX (+1) 858 - 484 - 1205
7810 Trade Street, Suite 100, San Diego, CA 92121, USA • [email protected] • www.vigitron.com
UMVi2700X_0120
LED Name Color Status Function
OFF Power is OFF
ON Power is ON
OFF No Connection
FLASHING Connection OK
OFF No connection
FLASHING Connection is OK with Traffic
OFF No PoE
ON PoE is ON
PoE
(Remote Side)
Status
Link/Act
Power GREEN
BLUE
ORANGE
GREEN
Top View
Left View Right View
3.46"
8.8 cm
0.98"
2.5 cm
1.76"
4.5 cm
www.vigitron.com
Made in U.S.A.
TM
52-57VDC
Electrical
Ethernet Interface Standard 10/100BaseT
Data Rate Auto select 10/100 Mbps
Cable Type** Single Pair 24/2 to 16/2 : Up to 3,000 feet (914m)
Power Source PoE Input, 36W Max. or
Local Power Supply, 48-57VDC
PoE Output 36W Max.
Power 3.5W using Local power supply or PoE
Consumption
Status LEDs Power On : Green LED
Status : Blue LED
PoE : Green LED
Standard Ethernet Traffic, Link,: Orange LED
Connectors Standard Ethernet : RJ-45 Connector
Single Pair Cable : Detachable 2-pin Terminal Block
Power: Barrel type DC005 5.5*2.1mm
RFC 2544 TCP/IP Packet Transmission
768 UDP, 2068 HTTP, 793 TCP
791 IP, 1783 TFTP, 894 IP over Ethernet
PoE Compatibility IEEE 802.3af, IEEE 802.3at
Regulatory
FCC Part 15, Subpart B, Class B 2010
Safety CE
Environmental RoHS, WEEE
Environmental
Humidity 0 to 95%, non-condensing
Temperature Operating: -30°C to +65°C per NEMA-TS2 testing
Storage: -40°C to +85°C
Mechanical
Dimensions 0.98x1.76x3.46 in., 2.5x4.5x8.8 cm (HxWxL)
Weight 0.225 lb, 102 g
Material Extruded Aluminum
Accessories
Vi0017 48VDC or Vi1120 57VDC wall-mount power supplies (optional)
* Specifications subject to change without notice.
**Caution must be taken not to exceed the current capacity of the installed wire.
Actual performance will depend on type and quality of cables. Cables must be direct runs as splices and
jumpers will result in lower performance.
24/2 AWG Twisted Unshielded (Cat5) 24/2 AWG Untwisted Unshielded 22/2 AWG Untwisted Unshielded
20/2 AWG Untwisted Unshielded 18/2 AWG Untwisted Unshielded** 18/2 AWG Solid Twisted Unshielded
10
20
30
40
50
60
70
80
90
100
110
0
0
100 200 300 400 500 600 700 800 900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 3000
Data Rate (Mbps)
Distance (Feet)
Vi27000 Series Data Rate Vs. Distance Chart
Distance (Feet)
Vi27000 Series PoE Power Vs. Distance
0
5
10
15
20
25
30
0 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 3000
Power Available at Camera (W)
** The 18/2 AWG Untwisted and 18/2 AWG Solid twisted overlap on PoE chart.
For distance testing, a Vigitron 36W PoE Midspan with 57VDC output is used as PoE source for the Vi27001.
Input PoE power and applied Voltage will affect PoE Distance performance. For long distance PoE applications
power supplies with 57VDC output are recommended.