Viking 201 Series User manual

Viking Installation Guid
Viking Rang Corporation
111 Front Str t
Gr nwood, Mississippi 38930 USA
[phone]
For product information,
call 1-888-VIKING1 (845-4641)
or visit th Viking W b sit at
vikingrang .com
F20880A EN (051612)
201/301/451 Series
Built-In Dishwashers

IMPORTANT
3
–Please Read and FollowTabl of Cont nts
Warnings & Important Information _____________________________________________________3
Dim nsions & Cutout Dim nsions _____________________________________________________6
Sp cifications _______________________________________________________________________7
Custom Door Pan l Sp cifications _____________________________________________________8
Custom Door Pan l Installation Option _________________________________________________9
G n ral Information ________________________________________________________________11
Sit Pr paration_________________________________________________________________11
Wat r Supply ___________________________________________________________________11
Drain __________________________________________________________________________11
El ctrical Conn ctions_______________________________________________________________12
Hardwir Conduit Option (201 & 301 Mod ls) ______________________________________13
Hardwir Conduit Option (451 Mod ls) ____________________________________________13
Trim Installation Options (451 Mod ls)_____________________________________________16
Count r Balanc Spring Adjustm nt (If N c ssary) __________________________________17
Installation_________________________________________________________________________18
P rformanc Ch cklist ______________________________________________________________22
T sting for L aks ________________________________________________________________22
Final Pr paration________________________________________________________________22
S rvic & R gistration _______________________________________________________________23
2
Site Preparation It is r comm nd d that a thorough sit insp ction b
conduct d PRIOR to unpacking and moving this applianc .
WARNING
Make sure that inc ming v ltage is the
same as unit rating. An electric rating
plate specifying v ltage, hertz, and amps
is attached t the pr duct. Wiring the
dishwasher with m re v ltage than it is
rated f r may cause severe damage. T
reduce the risk f fire, electric sh ck, r
injury t pers ns, installati n w rk and
electrical wiring must be d ne by qualified
technician in acc rdance with all
applicable c des and standards, including
fire-rated c nditi ns.
WARNING
The dishwasher d r may n t stay pen
by itself until the d r panel is installed.
Be aware f this when fastening the
dishwasher t the cabinet.
WARNING
Plumbing c nnecti ns must c mply with
applicable sanitary, safety and plumbing
c des.
WARNING
Electrical p wer must be turned ff at
circuit breaker r fuse b x bef re making
electrical c nnecti ns. Disc nnect the
electrical p wer supply and place a tag at
the disc nnect switch indicating that y u
are w rking n the circuit.
• B for b ginning–pl as r ad th s
instructions compl t ly and car fully.
•DO NOT r mov p rman ntly affix d
lab ls, warnings, or rating plat s from th
dishwash r. This may void warranty or
cr at an unsaf product.
• Pl as obs rv all national and local
cod s.
• Pl as nsur that this product is prop rly
ground d.
• Th install r should l av th s
instructions with th consum r who should
r tain for local insp ctor’s us and for
futur r f r nc .
• Th dishwash r has a factory install d
backflow pr v nt r. Do not add an
additional ch ck valv .
• Failur to provid a 20” abov floor l v l
(50.8 cm) high loop may r sult in improp r
op ration of th dishwash r.
• R mov pall t scr ws from bas . Damag
could occur to dishwash r if scr ws ar not
r mov d.

IMPORTANT
5
–Please Read and Follow
4
IMPORTANT–Please Read and Follow!
WARNING
ELECTRICAL SHOCK HAZARD
• Electrically gr und dishwasher.
• C nnect gr und wire t green gr und
c nnect r in terminal b x.
•DO NOT use an extensi n c rd.
• Failure t f ll w these instructi ns, can
result in death, fire r electrical sh ck.
WARNING
TIP OVER HAZARD
• DO NOT use dishwasher until
c mpletely installed.
• DO NOT push d wn n pen d r.
• D ing s can result in seri us injury
r cuts.
WARNING
EXCESSIVE WEIGHT HAZARD
Use tw r m re pe ple t m ve and
install dishwasher. Failure t d s can
result in back r ther injury.
WARNING
Disc nnect the electrical p wer supply and
place a tag at the disc nnect switch
indicating that y u are w rking n the
circuit.
WARNING
Be sure electrical p wer is turned ff at
circuit breaker r fuse b x bef re servicing
r installing unit. D n t use an extensi n
c rd f r this appliance.
WARNING
Impr per c nnecti n f the equipment –
gr unding c nduct r can result in a risk f
electric sh ck. Check with a qualified
electrician r serviceman if y u are in
d ubt as t whether the appliance is
pr perly gr unded. D n t m dify the plug
pr vided with the appliance; if it will n t fit
the utlet, have a pr per utlet installed by
a qualified electrician.
WARNING
Plumbing c nnecti ns must c mply with
applicable sanitary, safety, and plumbing
c des.
CAUTION
The dishwasher has a fact ry installed
backfl w preventer. D N t add an additi nal
check valve.
A GFI shall be used if required by NFPA-70
(National Ele tri Code), federal/state/lo al
laws, or lo al ordinan es.
• Th r quir d us of a GFI is normally
r lat d to th location of a r c ptacl with
r sp ct to any significant sourc s of wat r
or moistur .
• Viking Rang Corporation will NOT
warranty any probl ms r sulting from GFI
outl ts which ar not install d prop rly or
do not m t th r quir m nts b low.
If the use of a GFI is required, it should b :
• Of th r c ptacl typ (br ak r typ or
portabl typ NOT r comm nd d)
• Us d with p rman nt wiring only
(t mporary or portabl wiring NOT
r comm nd d)
• On a d dicat d circuit (no oth r
r c ptacl s, switch s or loads in th
circuit)
• Conn ct d to a standard br ak r of
appropriat siz (GFI br ak r of th sam
siz NOT r comm nd d)
• Rat d for Class A (5 mA +/- 1 mA trip
curr nt) as p r UL 943 standard
• In good condition and fr from any
loos -fitting gask ts (if applicabl in
outdoor situations)
• Prot ct d from moistur (wat r, st am,
high humidity) as much as r asonably
possibl

Sp cifications
7
Dim nsions & Cutout Dim nsions
6
28-3/4”
(73.0 cm)
33-7/8”
(86.0 cm)
49”
(124.5 cm)
23-7/8”
(60.6cm)
23-5/8”
(60.0 cm)
3”
(7.6 cm)
23-5/8”
(60.0 cm)
26-5/8”
(67.6 cm)
24”
(61.0cm)
24”
(61.0cm)
34”min.
(86.4cm)
to
35”min.
(89.0cm)
Note: A 2” (5.1 cm)
cut-out is required
for water supply
and discharge lines.
Built-In Dishwasher
Description 201 Models 301 Models 451 Models
Ov rall width 23-7/8” (60.6 cm)
Ov rall h ight from floor 33-7/8” (86.0 cm) min. to 35” (89.0 cm) max.
Ov rall d pth from r ar To dg of sid – 23-5/8” (60.0 cm) – includ s door pan l
With door op n – 49” (124.5 cm)
Cutout width 24” (61.0 cm)
Cutout h ight 34” (86.4 cm) min. to 35” (89.0 cm) max.
Cutout d pth 24” (61.0 cm)
El ctrical r quir m nts 15.0 amps, 120VAC/60 Hz;
3’9” (1.1 m) l ctrical cord 3 prong plug suppli d with unit.
Wat r-h ating l m nt rating 1200 watts
Inl t wat r t mp ratur 120°F (49°C) r quir d 120°F (49°C) r quir d 120°F (49°C)
r comm nd d;
Dishwash r will p rform
prop rly with cold wat r.
Note: Cycle times
will vary.
Inl t wat r pr ssur
op rating rang
10 to 125 psi (0.69 to 8.62 bar)
Inl t wat r hos 5’ (1.5 m) braid d stainl ss st l wat r lin with 3/8” (0.95 cm) compr ssion
fitting conn ct d to dishwash r
Drain hos 7’ (2.13 m) 1/2” (1.3 cm) ID “crimp-proof” fl xibl drain hos attach d to
dishwash r, conn ctions provid d for 5/8” (1.6 cm), 3/4” (1.9 cm) or
1” (2.5 cm), cut as r quir d
Drain hos high loop r quir d H ight from floor – 20” (51.0 cm) min.
Approximat shipping w ight 147 lbs. (66.7 kg) 152 lbs. (68.9 kg) 157 lbs. (71.2 kg)
Custom PanelProfessional

9
2
2
1
1
x2
4
x2
3
Locators
2
x4
Pr -drill two hol s with 1/8” drill bit for th locators
using dim nsions shown in th figur . Attach plastic
locators using th Torx (T20 BIT) pan h ad scr ws
provid d in th hardwar packag .
Pr -drill oth r four locations for wood scr ws
to attach th pan l to th dishwash r door using
th dim nsions shown in th figur .
1
1
3
11
1
1
4
2
x4
Us locators to align th pan l to th
dishwash r door hol s.
Us non-marring clamps to hold custom pan l in plac .
Us th truss h ad 1-3/4” long scr ws provid d in th
hardwar packag for th pan l attachm nt.
Note: If you are using any special panel material
and that require special screws, always use a #8 1-3/4”
long truss head Torx stainless steel screws. The screws
MUST BE stainless steel to avoid corrosion.
Hav th ov rlay pan l construct d p r dim nsions.
Th pan l thickn ss MAY NOT xc d 3/4" (1.91 cm)
for flush installation in most cabin ts. Ensur that th
d sign, construction, and installation of th pan l
ov rlay and its handl mounting is suffici nt to r liably
op rat in this application with a maximum pan l
w ight of 18 lbs. (8.2 kg.) Custom pan ls should not
xc d 18 lbs. (8.2 kg.)
Custom Door Pan l (Installation Option)
29-3/4”
(75.6 cm)
to
31-1/4”
(79.4 cm)
22-21/32”
(57.5 cm)
23-9/32"with trim
(59.1 cm)
or
23-7/8” without trim
(60.6 cm)
14”
(35.6 cm)
22-5/32”
(56.3 cm)
13-1/2”
(34.3 cm)
10-5/8”
(27.0 cm)
ø1/8” 4 places
(0.3 cm)
Locator
8
Custom Door Pan l
(Sp cifications for FDB301/FDB451 Mod ls)
Note: Back side of panel shown. Use caution not to drill through front of panel.
Note: If panels are made longer than 2 -3/4” (75.6 cm), the door panel will be taller than dishwasher control panel.
Note: All hole location dimmensions should be measured from the bottom of the door per the illustration above.

11
• R ad th s instructions car fully and
compl t ly b for installing th
dishwash r. Th installation should b
carri d out by a qualifi d install r, who is
familiar with all local cod s and ordinanc s
for l ctrical and plumbing conn ctions. If
th dishwash r is b ing install d for th
first tim , most of th work has to b don
b for you mov it into plac . If you ar
r placing an old dishwash r, you must
ch ck th old conn ctions.
• El ctrical r quir m nts ar list d in th
“Sp cifications” s ction.
Sit Pr paration
Note: It is recommended that a thorough
site inspection be conducted PRIOR to
unpacking and moving this appliance.
• After determinin where the water
supply line will connect to the
dishwasher, provide a 2” (5.1 cm) access
hole and run the line to the approximate
fill valve location. Sealin access area
once lines are in place is recommended.
• Confirm availabl acc ss to ad quat pow r.
Wat r Supply
• Wat r pr ssur for th wat r supply should
b a minimum of 10 to 125 psi. Th
dishwash r is suppli d with a 5’ (1.5 m)
braid d stainl ss st l wat r lin with 3/8”
(0.95 cm) compr ssion fitting conn ct d to
dishwash r.
• Aft r d t rmining wh r th wat r supply
lin will conn ct to th dishwash r, provid
a 2” (5.1 cm) acc ss hol and run th
wat r supply lin to th approximat fill
valv location.
• For s rvic conv ni nc , a shut-off valv
(not suppli d) should b install d in th
supply lin in a r adily acc ssibl location
(such as b n ath th sink).
•It is recommended that the dishwasher
be connected to a hot water supply.
Only th 451 mod l can b conn ct d to
th cold wat r supply. Cycl tim s will
incr as .
• It is important that th wat r supply lin
and th shut-off valv hav a suffici nt flow
volum . Flush th supply lin prior to
conn cting it to th intak lin of th
dishwash r.
• Mak sur th conn ction is s al d and not
l aking b for compl ting th installation.
Drain
• Th acc ss hol for th drain lin should
b 2” squar (5.1 cm). Locat as low and
as n ar to th back wall as possibl .
•DO NOT us any fittings anywh r in th
drain lin that ar l ss than 1/2” (1.3 cm) ID.
• If th drain lin is going to b conn ct d
to a food wast dispos r, b sur to
r mov th knockout or plug from th
fitting b for conn cting drain lin .
• Drain conn ction should b a minimum of
9” (22.9cm) from th floor. If conn ction is
low r, siphoning during cycl can occur.
Note: The end of the drain hose is 1” (2.5 cm),
but is adjustable to 3/4” (1. cm) or 5/8”
(1.6 cm). If the drain connection is smaller
than 1” (2.5 cm), the hose can be cut to fit
the connection.
Note: Be sure to run the drain line through
the hole to the sink compartment before
moving the dishwasher into place.
WARNING
Plumbing c nnecti ns must c mply with
applicable sanitary, safety, and plumbing
c des.
CAUTION
The dishwasher has a fact ry installed
backfl w preventer. D N t add an additi nal
check valve.
G n ral Information
10
5
x4
Verify operation of the door counter
balance springs after installation of
the overlay panel. The additional
weight of the overlay panel might
require an adjustment to the preload
of the counterbalance springs. If
adjustment of the springs is required,
please refer to the “Counter Balance
Spring” section.
Car fully tight n ach scr w to s cur th ov rlay
and ch ck to nsur that th ov rlay is squar with th
dishwash r door and cabin t op ning and that th pan l
do sn’t int rf r with th op ration of th dishwash r.
Custom Door Pan l (Installation Option, cont.)

13
5
1
2
1
1
6
2
Black
(Line)
White
(Neutral)
Hardwir Conduit Option (201 & 301 Mod ls)
1
3
2
x4
2
1
3
3
x2
2
1
4
R mov front plat . R mov factory install d pow r
cabl from t rminal block.
Attach UL approv d 3/4” strain r li f (not includ d) to
bottom of t rminal box. Run wir s through strain r li f.
Conn ct wir s to t rminal block.
R mov any loos it ms in th dishwash r and car fully
lay th dishwash r on its back. Note: Be careful not to
pinch hoses or power cord beneath dishwasher.
R mov bottom pan. Note: Rapid removal of the bottom pan will
cause damage to the moisture sensor. For installation and servicing,
slowly pull the bottom pan from the unit and disconnect the wire
from the moisture sensor, which is located in the center of the pan.
12
Grounding Instructions
This applianc must b ground d. In th
v nt of a malfunction or br akdown,
grounding will r duc th risk of l ctric
shock by providing a path of l ast r sistanc
for l ctric curr nt. This applianc is
quipp d with a cord having an quipm nt-
grounding conductor and a grounding plug.
Th plug must b plugg d into an
appropriat outl t that is install d and
ground d in accordanc with all local cod s
and ordinanc s.
Groundin Instructions if Hardwired:
This applianc must b conn ct d to a
ground d m tal, p rman nt wiring syst m;
or an quipm nt grounding conductor must
b run with th circuit conductors and
conn ct d to th quipm nt – grounding
t rminal or l ad on th applianc .
• For a cord conn ct d und rcount r
dishwash r:
1. Th pow r supply r c ptacl for th
applianc should b install d in a
cabin t or on a wall adjac nt to th
und r count r spac in which th
applianc is to b install d;
2. Th r should b an op ning through
th partition b tw n th
compartm nts m ntion d in It m (1),
that is larg nough for th attachm nt
plug to pass through. Th long st
dim nsion of th op ning shall not b
mor than 1-1/2” (38 mm).
3. Th dg s of th op ning m ntion d in
It m (2) should, if th partition is wood,
b smooth and round d or, if th
partition is m tal, b cov r d with th
gromm t provid d for this purpos by
th manufactur r; and
El ctrical Conn ctions
4. Car should b x rcis d, wh n th
applianc is install d or r mov d to
r duc th lik lihood of damag to th
pow r supply cord.
• Th dishwash r com s with a 3’9” (1.1 m)
l ctrical cord for 110-120 volts, 15/20
amp supply. This cord should b plugg d
into th 110-120 volt outl t locat d und r
th sink.
• If th cord is not long nough or if a hard
wir installation is n d d, follow th
instructions in th “Hardwir ” s ction.
Note: Access holes should be 2” square
(5.1 cm) with no sharp edges.
• In a hardwir installation, us only copp r
supply conductors. Th conductors should
hav a minimum t mp ratur rating of
194° F (90° C).
WARNING
Disc nnect the electrical p wer supply and
place a tag at the disc nnect switch
indicating that y u are w rking n the
circuit.
WARNING
Be sure electrical p wer is turned ff at
circuit breaker r fuse b x bef re servicing
r installing unit. D n t use an extensi n
c rd f r this appliance.
WARNING
Impr per c nnecti n f the equipment –
gr unding c nduct r can result in a risk f
electric sh ck. Check with a qualified
electrician r serviceman if y u are in
d ubt as t whether the appliance is
pr perly gr unded. D n t m dify the plug
pr vided with the appliance; if it will n t fit
the utlet, have a pr per utlet installed by
a qualified electrician.

15
Hardwir Conduit Option (451 Mod ls, cont.)
5
1
2
1
1
6
2
Black
(Line)
White
(Neutral)
1
7
2
3
Green
(Ground)
2
8
1
x4
3
4
Conn ct ground wir . Tight n scr ws on strain r li f.
NNoottee: Reinstall terminal block cover and front plate.
Run wir through gromm t on bottom pan.
R plac bottom pan.
Attach UL approv d 3/4” strain r li f (not includ d) to
bottom of t rminal box. Run wir s through strain r li f.
Conn ct wir s to t rminal block.
14
1
7
2
3
Green
(Ground)
2
8
1
x4
3
4
Conn ct ground wir . Tight n scr ws on strain r li f.
NNoottee: Reinstall front plate.
Run wir through gromm t on bottom pan.
R plac bottom pan.
1
3
2
x4
2
1
R mov any loos it ms in th dishwash r and car fully
lay th dishwash r on its back. Note: Be careful not to
pinch hoses or power cord beneath dishwasher.
R mov bottom pan. Note: Rapid removal of the bottom pan will
cause damage to the moisture sensor. For installation and servicing,
slowly pull the bottom pan from the unit and disconnect the wire from
the moisture sensor, which is located in the center of the pan.
3
3
x2
2
1
3
4
2
1
R mov front plat . R mov t rminal block cov r. R mov factory install d
pow r cabl from t rminal block.
Hardwir Conduit Option (201 & 301 Mod ls, cont.)
Hardwir Conduit Option (451 Mod ls)

17
Count r Balanc Spring Adjustm nt (if n c ssary)
1
1
2
1
2
2
Disconn ct cabl from hook. R mov spring from dishwash r.
3
Increase
tension
Decrease
tension
1
4
2
S t count r balanc spring conn ctor in appropriat
location.
R conn ct cabl to hook.
Note: For custom panel installation,
the door may require adjustment
to the preload of the counterbalance
springs. Follow these steps to
adjust the tension.
16
1a
Trim Installation Options (451 Mod ls)
Dishwash r ships with trim install d for flush install. If
n d d, attach wip r gask t to dishwash r by pulling
prot ctiv film off adh siv back. Apply b hind
h mm d dg of sid trim.
22
1b
1
x6
2b
To install dishwash r without trim, r mov
th 6 scr ws (3 p r sid ) and r mov trim.
If n d d, attach wip r gask t to dishwash r by pulling
prot ctiv film off adh siv back. Apply to l ading
dg of dishwash r fram . Trim gask t to fit.

19
2
1
6
DOWN
UP
7a
DOWNUPDOWNUP DOWNUPDOWNUP
DOWN UP
Equal distance
7b
DOWNUPDOWNUP
DOWNUPDOWNUP
DOWNUPDOWNUP
DOWNUPDOWNUP
DOWNUPDOWNUP
DOWNUPDOWNUP
DOWNUPDOWNUP
DOWNUPDOWNUP
1
2
Equal distance
8
Installation (cont.)
Slid unit into op ning; b sur to f d wat r, l ctrical
and discharg lin s into adjac nt cabin t.
For 301 & 451 mod ls, plac a l v l on handl , th n
adjust to appropriat h ight. L ft and right adjust sid
to sid and c nt r adjusts front to back.
For 201 mod ls, r mov front pan l to acc ss th front
l v ling l gs. L v ling l gs will b rais d during
shipping. Adjust front l v ling l gs down using a 1/4
driv ratch t. Wh n th adjustm nt nut is visibl ,
compl t th low ring of th l gs from th top. Wh n
th l gs ar down, tight n th locking nut on th top
of th l g. To l v l c nt r r ar l g, s St p 7a.
To ch ck l v l, front to back, pull th top rack half-way out of
unit. Th rack should r main stationary and not mov in or out.
Note: Leveling is important for optimal performance.
18
Installation
2
2
1
x4
3
4
1
2
1
2
Car fully lay dishwash r on its back and attach th kick
plat brack ts. Scr ws for th brack ts will alr ady b
in th bas . NNoottee: Be careful not to pinch hoses or
power cord beneath dishwasher.
To adjust th d pth of th kick plat , loos n scr ws on
th brack t and position in th r quir d d pth. Tight n
scr ws and r p at for oth r sid .
3
1
1
4a
2
x2
Using ti strap attach d to dishwash r, band wat r lin ,
drain lin , and pow r cord tog th r.
For installation with trim, attach brack ts with two
scr ws (1 p r brack t).
1
1
4b
2
x2
5
For installation without trim, attach brack ts with two
scr ws (1 p r brack t).
Position unit in front of cutout.
L v ling

21
12c
Air Gap
12d
Air Gap
(Discharg with air gap) (Discharg with food wast dispos r and air gap)
13
14
Conn ct wat r lin . Plug LED light into dishwash r (s l ct mod ls only)
and install kick plat .
Note: DO NOT block the dry air exhausts (rectangular
slots on the access panel) with kick plate or base board.
Blocking the opening could reduce the dry performance
and cause unwanted condensation.
Final Installation (cont.)
20
9a
x2
3
1
2
x4
9b
x2
For installation with trim, s cur dishwash r by
attaching provid d mounting plugs and wood scr ws
through trim pan ls into cabin ts. Attach scr ws
through top brack ts into cabin ts.
For installation without trim, s cur dishwash r by
attaching scr ws through top brack ts into cabin ts.
Minimum
20”
(50.8 cm)
from floor
10
1.0”
(2.5 cm)
Cut here for
3/4” (1.9 cm)
Cut here for
5/8” (1.6 cm)
11
Install High Loop Clip, which is provid d, a minimum of
20” (50.8 cm) from th floor. R f r to th Drain s ction
of "General Information" for prop r installation
r quir m nts.
Id ntify discharg conn ction siz ; cut lin to corr ct
siz and conn ct. Clamp if n c ssary.
12a
12b
(Discharg with food wast dispos r)
Note: Be sure to remove the knockout or plug from the
fitting of the disposer before connecting drain line.
(Standard discharg )
Final Installation

23
S rvic & R gistration
Only authoriz d r plac m nt parts may b us d in p rforming s rvic on th applianc . Do not
r pair or r plac any part of th applianc unl ss sp cifically r comm nd d in th manual. All
s rvicing should b r f rr d to a qualifi d t chnician.
Contact Viking Rang Corporation, 1-888-VIKING1 (845-4641), for th n ar st s rvic parts
distributor in your ar a or writ to:
VIKING RANGE CORPORATION
PREFERRED SERVICE
1803 Hwy 82W
Greenwood, Mississippi 38930 USA
Th s rial numb r and mod l numb r for your dishwash r ar locat d on th id ntification plat mount d
on th bottom l ft sid of th dishwash r door op ning.
R cord th following information indicat d b low. You will n d it if s rvic is v r r quir d.
Mod l numb r ____________________________________________________________________________________
S rial numb r _____________________________________________________________________________________
Dat of purchas __________________________________________________________________________________
Dat install d ______________________________________________________________________________________
D al r's nam _____________________________________________________________________________________
Addr ss ___________________________________________________________________________________________
These installation instructions should remain with the
dishwasher for future reference.
22
T sting for L aks
A qualifi d install r should carry out th following
ch cks:
hR mov packaging and parts.
hTurn on th wat r supply and ch ck for l aks.
hTurn th pow r on at br ak r/fus box and
t st th dishwash r op ration by running a
rins and hold cycl . (This should tak about
12 minut s.)
hTurn off th l ctrical pow r and ch ck for
l aks und r th dishwash r.
hMak sur that no kinks hav d v lop d in
th drain lin s.
Final Pr paration
• Som stainl ss st l parts may hav a plastic
prot ctiv wrap which must b p l d off.
POTS
PANS
CYCLES
NOR MAL
WAS H
LIGHT
CHINA
FAS T
WAS H
RINSE
HOLD
CLEAN HI T E MP
WASH
SANITIZED TOP
WAS H
SANITIZED
155 F R INS E
DE LAY
STAR T
OPTIONS
Va ri-P re s sure Intelli-W as h
Quiet C lean S ystem
Airflo Gentle Dry
2
4
6
8
10
OptionsCycles
Unit R s t
• If th unit should n d to b r s t for any
r ason, push and hold th “START” button for
4 s conds.
P rformanc Ch cklist