Viking VBO1811 Technical manual

Viking Use/Installation Guide
Outdoor Cabinets
VIKING RANGE CORPORATION
111 Front Street
Greenwood, Mississippi 38930 USA

2
IIMMPPOORRTTAANNTT--PPLLEEAASSEERREEAADDAANNDDFFOOLLLLOOWW
•Before beginning, please read these instructions completely and carefully.
•Do not remove permanently affixed labels, warnings, or plates from product. This may void the warranty.
•The installer should leave instructions with the consumer who should retain for future reference
TTOOIINNSSTTAALLLLCCAABBIINNEETTSS::
1. Verify cabinet product number(s) on
box(es) to list of cabinets ordered.
2. Carefully unpack cabinets making sure
not to scratch fronts. Front panels are
protected by plastic coating (that must
be removed after setup). Cabinets with
interchangeable doors are shipped from
the factory with opening from left to
right as shown (See illustration #1).
3. In cabinets with interchangeable doors,
hardware package will contain hole
covers and hardware to install.
4. Install 4 legs in the leg plates attached to
bottom of each cabinet. Screw in place.
(See illustration #2).
IIlllluussttrraattiioonn##11
IIlllluussttrraattiioonn##22
CCaabbiinneettbbooxxrreeaaddyy
ffoorraasssseemmbbllyy

3
IIlllluussttrraattiioonn##33
IIlllluussttrraattiioonn##44
IInnssttaallll44TTiinnnneerrmmaanncclliippss((pprroovviiddeedd))
bbeeffoorreeffaasstteenniinnggccaabbiinneettssttooggeetthheerr
MMoouunnttccaabbiinneettss
wwiitthh##1100xx11//2
2””
ssccrreewwsspprroovviiddeedd
UUssee##88xx33//88””mmaacchhiinneessccrreewwaanndd
lloocckknnuuttttooffaasstteennhhoolleeccoovveerrttoo
iinnssiiddeeddoooorrppaanneell
UUssee##88xx33//88””ffllaatt
h
heeaaddMM..SS..aanndd
lloocckknnuuttttooaattttaacchh
hhiinnggeebbrraacckkeettttoo
tthheeiinnssiiddeeddoooorr..
7. Cabinet doors must be adjusted when cabinets are
level in final position. There are two adjustment
screws on the hinge receiver. (See Illustration #5)
•The front screw is used to center the door in
the opening. Turning the front screws in or
out will center the door over the cabinet
opening.
•The back screw is used to align the front of
the door with the cabinet frame and secure
the door to the cabinet. Slightly loosen the
screw and slide door in or out. Retighten the
screw to secure the door.
IIlllluussttrraattiioonn##55
FFrroonnttSSccrreeww
5. Place cabinet(s) in approximate final position.
Level cabinets using leveling legs. Use 1/2"
SMS screws provided to screw cabinets
together. (See illustration #3).
6. Determine appropriate hinge side for cabinets
with interchangeable doors. Remove outside
door panel. Install hinges by placing plate in
hole in door and fasten in place with hardware
provided. Screw hinge plates in appropriate
pre-drilled holes in cabinet side. Fasten hole
covers with hardware provided. (See
Illustration #4).
BBaacckkSSccrreeww

4
8. If desired, snap toe kick
included with each unit to
front legs. (See illustration
#6).
IIlllluussttrraattiioonn##66
IIlllluussttrraattiioonn##77
SSnnaappttooeekkiicckkttooffrroonntt
lleeggss
9. SSIIDDEEPPAANNEELLIINNSSTTAALLLLAATTIIOONN((EEnnddooffRRuunnOOnnllyy))
•Remove all drawers. (If applicable)
•Remove all protective covering from panel and install using the #10 x 1/2” tek screws provided. (See
Illustration #7)
•Attach toe kick to legs (See Illustration #6).
NNOOTTEE::
FFOORRWWAALLLLIINNSSTTAALLLLAATTIIOONNSS::
The front portion of the side toe kick must be shortened to match the front toe kick. (See Illustration #7).
The plastic material can be cut with any common type wood saw blade.
FFOORRIISSLLAANNDDIINNSSTTAALLLLA
ATTIIOONNSS::
The side, front, and rear toe kick must be modified (See Illustration #7)
22..AAttttaacchhffrroommiinnssiiddee((ffrroonnttaannddrreeaarr))
11..PPllaacceessiiddeeppaanneelliinnttooaarreeaaooff
tthheeccaabbiinneett
SSiiddeettooeekkiicckk((BB))FFrroonnttttooeekkiicckk((AA))
LLHHSSiiddeePPaanneellIInnssttaallllaattiioonn
((RRHHiinnssttaallllsstthheessaammeewwaayy))
TTooeeKKiicckkDDiimmeennssiioonnss
WWaallllIInnssttaallllaattiioonnIIssllaannddIInnssttaallllaattiioonn
FFrroonnttTTooeeKKiicckk((AA))116633//44””((4422..55ccmm))116633//44””((4422..55ccmm))
SSiiddeeTTooeeKKiicckk((BB))227711//44””((6611..66ccmm))225511//22””((6644..88ccmm))
RReeaarrTTooeeKKiicckk((CC))NN//AA116633//44””((4422..55ccmm))

5
10. BBAACCKKPPAANNEELLIINNSSTTAALLLLAATTIIOONN
•Remove all protective covering from panel and install using the #10 x 1/2” tek screws provided. (See
Illustration #8).
•Attach rear toe kick to legs. (See illustration #8).
NNOOTTEE::For end of the run panels, the rear, front, and side toe kicks must be modified. (See illustrations #7 & #8)
22..FFaasstteennffrroommiinnssiiddeewwiitthh((44))11//22””tteekkssccrreewwsspprroovviiddeedd
BBaacckkppaanneell
11..PPllaacceebbaacckkppaanneelloonnttooccaabbiinneettaarreeaa
33..AAfftteerrmmooddiiffyyiinnggrreeaarrttooeekkiicckk((SSeeeeddiimmeennssiioonn
cchhaarrttaatttthheebboottttoommooffppaaggee44))--ssnnaappttooee
kkiicckkiinnttoo
ppllaaccee
RReeaarrttooeekkiicckk
11. IINNSSTTAALLLLLLOOCCAALLLLYYSSUUPPPPLLIIEEDDCCOOUUNNTTEERRTTOOPP
Viking outdoor cabinets are designed for a minimum countertop thickness of 1 1/8” (2.9 cm) such as you would
find with granite or quartz material. If a countertop material thicker than 1 1/2” (3.8 cm) is used, the appliances
should be shimmed to the proper height. For examples of common installations, see the Viking Stainless Steel
Planning Guide.
12. Install Viking appliances per each appliance's installation instructions.
CCoommpplleetteeCCaabbiinneett
IIlllluussttrraattiioonn##88

6
OVERALL WIDTH OVERALL HEIGHT OVERALL DEPTH
VBBO1601 15 5/8” (39.7 cm) 34 1/2” (87.6 cm) 29 7/8” (75.9 cm)
VBBO2602 26 3/8” (67.0 cm) 34 1/2” (87.6 cm) 29 7/8” (75.9 cm)
VBO1811, including doors 18” (45.7 cm) 34 1/2” (87.6 cm) 29 7/8” (75.9 cm)
VTPO1810, including doors 18” (45.7 cm) 34 1/2” (87.6 cm) 29 7/8” (75.9 cm)
VBO1830, including doors 18” (45.7 cm) 34 1/2” (87.6 cm) 29 7/8” (75.9 cm)
VSBO2402, including doors 24” (61.0 cm) 34 1/2” (87.6 cm) 29 7/8” (75.9 cm)
VSBP3602, including doors 36” (91.4 cm) 34 1/2” (87.6 cm) 29 7/8” (75.9 cm)
VQBO3021, VQWO3010 30 1/4” (76.8 cm) 34 1/2” (87.6 cm) 29 7/8” (75.9 cm)
VQBO4121, VQWO4120 41 7/8” (106.4 cm) 34 1/2” (87.6 cm) 29 7/8” (75.9 cm)
VQBO5322, VQWO5311 53 7/8” (136.8 cm) 34 1/2” (87.6 cm) 29 7/8” (75.9 cm)
VERO3200 32” (81.3 cm) 68” (172.7 cm) 29 7/8” (75.9 cm)
VEUO3202 32” (81.3 cm) 68” (172.7 cm) 29 7/8” (75.9 cm)
VGRO3200 32” (81.3 cm) 68” (172.7 cm) 29 7/8” (75.9 cm)
VGUO3202 32” (81.3 cm) 68” (172.7 cm) 29 7/8” (75.9 cm)
VURO3200 32” (81.3 cm) 34 1/2” (87.6 cm) 29 7/8” (75.9 cm)
VURO2400 24” (61.0 cm) 34 1/2” (87.6 cm) 29 7/8” (75.9 cm)
VBPFLR4 4” (10.2 cm) 34 1/2” (87.6 cm)* 3/4” (1.9 cm)
VFLR4 4” (10.2 cm) 34 1/2” (87.6 cm)* 3/4” (1.9 cm)
VSP30 29 7/8” (75.9 cm) 34 1/2” (87.6 cm)* 0”
VTSP30 29 7/8” (75.9 cm) 68” (172.7 cm)* 0”
VTHP30 29 7/8” (75.9 cm) 34” (86.4 cm)* 0”
VCF90 3” (7.6 cm)** 34” (86.4 cm)* 3/4” (1.9 cm)
VOCF90 33” (83.8 cm)** 34 1/2” (87.6 cm)* 3/4” (1.9 cm)
VCF135 3” (7.6 cm)** 34 1/2” (87.6 cm)* 3/4” (1.9 cm)
VOCF135 15 1/2” (39.4 cm)** 34 1/2” (87.6 cm)* 3/4” (1.9 cm)
VBP16 16” (40.6 cm) 34 1/2” (87.6 cm)* 3/4” (1.9 cm)
VBP18 18” (45.7 cm) 34 1/2” (87.6 cm)* 3/4” (1.9 cm)
VBP24 24” (61.0 cm) 34 1/2” (87.6 cm)* 3/4” (1.9 cm)
VBP26 26 3/8” (67.0 cm) 34 1/2” (87.6 cm)* 3/4” (1.9 cm)
VBP30 30 7/8” (78.4 cm) 34 1/2” (87.6 cm)* 3/4” (1.9 cm)
VBP32 32” (81.3 cm) 34 1/2” (87.6 cm)* 3/4” (1.9 cm)
VBP36 36” (91.4 cm) 34 1/2” (87.6 cm)* 3/4” (1.9 cm)
VBP41 41 7/8” (106.4 cm) 34 1/2” (87.6 cm)* 3/4” (1.9 cm)
VBP53 53 7/8” (136.8 cm) 34 1/2” (87.6 cm)* 3/4” (1.9 cm)
VTBP32 32” (81.3 cm) 68” (172.7 cm)* 3/4” (1.9 cm)
BBAASSIICCSSPPEECCIIFFIICCAATTIIOONNSS
*includes provided toe kick
**from inside of turn to next cabinet

PPRROOFFEESSSSIIOONNAALLSSEERRIIEESS
OOUUTTDDOOOORRCCAABBIINNEETTWWAARRRRAANNTTYY
OONNEEYYEEAARRFFUULLLLWWAARRRRAANNTTYY
Outdoor cabinets and all of their component parts, except as detailed below*, are warranted to be free from defective materials or workmanship
in normal household use for a period of twelve (12) months from the date of original retail purchase. Viking Range Corporation, warrantor,
agrees to repair or replace, at its option, any part which fails or is found to be defective during the warranty period.
*Decorative items are warranted to be free from defective materials or workmanship for a period of ninety (90) days from the date of original
retail purchase. ANY DEFECTS MUST BE REPORTED TO THE SELLING DEALER WITHIN NINETY (90) DAYS FROM DATE OF ORIGINAL RETAIL
PURCHASE.
TTWWOOYYEEAARRLLIIMMIITTEEDDWWAARRRRAANNTTYY
Any door hinges or drawer slides which fail due to defective materials or workmanship in normal household use during the second year from the
date of original retail purchase will be repaired or replaced, free of charge for the part itself, with the owner paying all other costs, including
labor.
LLIIFFEETTIIMMEELLIIMMIITTEEDDWWAARRRRAANNTTYY
Any stainless steel part which rruussttssthrough due to defective materials or workmanship in normal household use during the second through the
useful lifetime of the cabinet from the date of original retail purchase will be repaired or replaced, free of charge for the part itself, with the
owner paying all other costs, including labor.
This warranty extends to the original purchaser of the product warranted hereunder and to each transferee owner of the product during the term
of the warranty.
This warranty shall apply to products purchased and located in the United States and Canada. Products must be purchased in the country where
service is requested. Warranty labor shall be performed by an authorized Viking Range Corporation service agency or representative. Warranty
shall not apply to damage resulting from abuse, accident, natural disaster, loss of electrical power to the product for any reason, alteration,
outdoor use, improper installation, improper operation, or repair or service of the product by anyone other than an authorized Viking Range
Corporation service agency or representative. This warranty does not apply to commercial usage. Warrantor is not responsible for consequential
or incidental damage whether arising out of breach of warranty, breach of contract, or otherwise. Some jurisdictions do not allow the exclusion
or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
Owner shall be responsible for proper installation, providing normal care and maintenance, providing proof of purchase upon request, and
making the appliance reasonably accessible for service. If the product or one of its component parts contains a defect or malfunction during the
warranty period, after a reasonable number of attempts by the warrantor to remedy the defects or malfunctions, the owner is entitled to either a
refund or replacement of the product or its component part or parts. Warrantor’s liability on any claim of any kind, with respect to the goods or
services covered hereunder, shall in no case exceed the price of the goods or service or part thereof which gives rise to the claim.
WWAARRRRAANNTTYYSSEERRVVIICCEE: Under the terms of this warranty, service must be performed by a factory authorized Viking Range Corporation service
agent or representative. Service will be provided during normal business hours, and labor performed at overtime or premium rates shall not be
covered by this warranty. To obtain warranty service, contact the dealer from whom the product was purchased, an authorized Viking Range
Corporation service agent, or Viking Range Corporation. Provide model and serial number and date of original purchase. For the name of your
nearest authorized Viking Range Corporation service agency, call the dealer from whom the product was purchased or Viking Range Corporation.
IIMMPPOORRTTAANNTT: Retain proof of original purchase to establish warranty period.
The return of the Owner Registration Card is not a condition of warranty coverage. You should, however, return the Owner Registration Card so
that Viking Range Corporation can contact you should any question of safety arise which could affect you.
Any implied warranties of merchantability and fitness applicable to the above described door hinges, drawer slides, and stainless steel parts are
limited in duration to the period of coverage of the applicable express written limited warranties set forth above. Some jurisdictions do not
allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal
rights, and you may also have other rights which may vary from jurisdiction to jurisdiction.
Specifications subject to change without notice
1. Carefully remove protective plastic peel coat from each stainless steel surface. Clean stainless with stainless steel
cleaner in direction of grain. Clean the stainless with any product made for stainless. Always rub with the grain
direction. Rubbing across the grain direction may produce minor scratches. Some good cleaners are Stainless Steel
MagicTM, and Sheila ShineTM.
2. In a salt air environment, a slightly more oily cleaner like Sheila ShineTM will protect better against oxidation or slight
surface rust. Cleaning the surfaces periodically will protect the finish for many years.
CCAARREEAANNDDMMAAIINNTTEENNAANNCCEE
CCAAUUTTIIOONN
•Do not use a metal knife or any other metal tool to scrape stainless steel parts.
•Do not permit citrus or tomato juice to remain on stainless steel surfaces, as citric acid will permanently discolor
stainless steel. Wipe up any spills immediately.
•Do not use abrasive cleaners, steel wool pads, or abrasive cloths as they will scratch the product.

F20402 (PS0106VR)
Viking Range Corporation
111 Front Street
Greenwood, Mississippi 38930 USA
[phone]
For more product information
call 1-888-VIKING1 (845-4641),
or visit the Viking Web site
vikingrange.com