Viking Designer DDBB363 User manual

Spe ifi ations (Designer Bottom-Mount)
27
24”
(61.0 cm)
35”
(88.9cm)
51–1/2”
(130.8cm)
23–1/16”
(58.5cm)
3–1/2”
(8.9cm)
9–5/32”
(23.3cm)
82–7/8”
(210.5 cm)
min.
to
84–1/16”
(213.5 cm)
max.
20–3/4”
(52.7 cm)
23–3/8”
(59.4 cm)
1–1/2”
(3.8cm)
26”
(66.0 cm)
36”
(91.5 cm)
Dimensions (Designer Bottom-Mount)
26
Designer 36” 36” Desig er Bottom-Mou t
Descriptio DDBB363
Overall width 36” (91.5 m)
Overall height from bottom 82-3/4” (210.2 m) min. to 84-1/16” (213.5 m) max.
Overall depth from rear To front edge of side trim: 23-3/8” (59.4 m)
To front of top grille: 24” (61.0 m)
To front of handle: 26” (66.0 m)
Cutout width 36” (91.5 m)
Cutout height 82-7/8” (210.5 m) min. to 84-1/16” (213.5 m) max.
Cutout depth 24” (61.0 m) min.
Ele tri al requirements 115 volt, 60 Hz, 15 amp dedi ated ir uit; 3-wire ord with
grounded 3-prong plug atta hed to produ t
Maximum amp usage 9.9 amps
Inlet water 1/4” opper tubing inlet waterline; minimum 20 psi;
Requirements maximum 120 psi
Overall interior dimensions
Refrigerator 15.2 u. ft. (431 Liters)
Freezer 5.1 u. ft. (145 Liters)
Total apa ity 20.3 u. ft. (576 Liters)
Approximate shipping weight 565 lbs. (254.3 kg)

One 2”x 4” Mounting Board
1–1/2” (3.8 cm) x3–1/2” (8.9 cm)
NOTE: If unit is installed deeper than 24” (61.0 cm), thenshim
behind the mounting board by the difference.
Bottom of anti-tip board is 3–7/8” (9.8 cm) belowopening height.
NOTE: Top of unit must be placed firmly under anti-tip board.
Anti-Tip Location
79–3/8”
(201.6 cm) min.
to bottomof
anti-tipboard
80–1/2”
(204.6 cm) max.
to bottomof
anti-tipboard
29”
(73.7 cm)
3–1/2”
(8.9 cm)
1–1/2”
(3.8 cm)
Anti-Tip Dimensions (Designer Bottom-Mount)
29
9”
(22.9cm)
73–3/8”
(186.4 cm)
82–7/8”
(210.5 cm) min.
anti-tip board&
opening height
84–1/16”
(213.5cm) min.
anti-tip board&
opening height
36”
(91.5 cm)
24”
(61.0 cm)
Electric Outlet Location
Water Line Entry Area
36”
(91.5 cm)
6–3/4”
(17.1 cm)
7–5/8”
(19.4 cm)
3”
(7.6 cm)
5/8”
(1.5 cm)
5/8”
(1.5 cm)
10–1/2”
(26.7 cm)
5/8”
(1.5 cm)
10–3/4”
(27.3 cm)
1”
(2.5cm)
3–5/8”
(9.2 cm)
Optional floor
water line entry
SeeAnti-Tip boardinstallation
6”
(15.2cm)
Cutout Dimensions (Designer Bottom-Mount)
28
36” Designer 36” Designer

Top View
Top View
Door
24”
(61.0 cm)
Standard
Cabinet
Depth
25”
(63.5 cm)
Countertop
Depth
Wall
3/4”
(1.9 cm)
Full End
Panel
Door
Wall
1”
(2.5 cm)
If standard
25” (63.5 cm)
standard
cabinet depth
is used
3/4”
(1.9 cm)
Full End
Panel
25”
(63.5 cm)
Flush
1”
(2.5 cm)
If standard
25” (63.5 cm)
standard
cabinet depth
is used
Flush
Cabinet Information (Designer)
31
Top View
Overlapping cabinet doors
Top View
Flush mount cabinet doors
Door
24”
(61.0cm)
Standard
Cabinet
Depth
24-3/4”
(62.9 cm)
Wall
3/4”
(1.9 cm)
Full End
Panel
3/4”
(1.9 cm)
If standard
25” (63.5 cm)
standard
cabinet depth
is used
Flush
Cabinet
Door
Door
Wall
3/4”
(1.9 cm)
Full End
Panel
1”
(2.5 cm)
If standard
25” (63.5 cm)
standard
cabinet depth
is used
Flush
25”
(63.5 cm)
Cabinet
Depth
Cabinet
Door
Cabinet Information (Designer)
30
Designer models fit flush in standard 24” (61.0 m) deep abinet openings with no protrusion into the
room ex ept 2”(5.1 m) urved handle depth.
Designer models fit flush in standard 24” (61.0 m) deep abinet openings with no protrusion into the
room ex ept 2”(5.1 m) urved handle depth.