Viking Designer DFBB363 User manual

Spe ifi ations (Bottom Mount)
3
51-7/8”
(131.8 cm)
23-1/16”
(58.6 cm)
3-1/2”
(8.9 cm)
82-7/8”
(210.5 cm)
min.
to
84-1/16”
(213.5 cm)
max.
Measurement varies
(locally supplied hardware)
23 13/16”
(60.5 cm)
24 3/4”
(62.9 cm)
35”
(98.9 cm)
36”
(91.4 cm)
Dimensions (Bottom Mount)
2
36” Botto Mount
Description DFBB363
Overall width 36” (91.5 m)
Overall height (from bottom) 82-3/4” (210.2 m) min. to 84-1/16” (213.5 m) max.
Overall depth (from rear) To front edge of side trim: 23-13/16” (60.5 m)
To front of top grille: 24-3/4” (62.9 m)
To front edge of door trim: 24” (61.0 m)
Cutout width 36” (91.5 m)
Cutout height 82-7/8” (210.5 m) min. to 84-1/16” (213.5 m) max.
Cutout depth 24” (61.0 m) min.*
Ele tri al requirements 115 volt, 60 Hz, 15 amp dedi ated ir uit; 3-wire ord with
grounded 3-prong plug atta hed to produ t
Maximum amp usage 9.9 amps
Inlet water 1/4” opper tubing inlet waterline; minimum 20 psi;
requirements maximum 120 psi
Overall interior dimensions
Refrigerator 15.2 u. ft. (431 liters)
Freezer 5.1 u. ft. (145 liters)
Total apa ity 20.3 u. ft. (576 liters)
Maximum panel weight Fresh food 45 lbs. (20.4 kg) Freezer 20 lbs. (9.0 kg)
Approximate shipping weight 500 lbs. (227.3 kg)
*Full overlay models fit flush in 25” (63.5 m) deep abinet openings. They an be installed in standard 24” (61.0 m)
deep openings. The door fa es and top grille will protrude 3/4” (1.9 m) into the room.
36” Bottom Mount

54
9”
(22.9 cm)
73-3/8”
(186.4 cm)
82-7/8”
(210.5 cm) min.
anti-tip board &
opening height
84-1/16”
(213.5 cm) max.
anti-tip board &
opening height
36”
(91.5 cm)
24”
(61.0 cm)
Electric outlet location
Water line entry area
36”
(91.5 cm)
6-3/4”
(17.1 cm)
7-5/8”
(19.4 cm)
3”
(7.6 cm)
5/8”
(1.5 cm)
5/8”
(1.5 cm)
10-1/2”
(26.7 cm)
5/8”
(1.5 cm)
10-3/4”
(27.3 cm)
1”
(2.5 cm)
3-5/8”
(9.2 cm)
Optional floor
water line entry
See anti-tip board installation
6”
(15.2 cm)
9”
(22.9 cm)
Cutout Dimensions (Bottom Mount)
36” Bottom Mount
One 2”x 4” mounting board
1-1/2” (3.8 cm) x 3-1/2” (8.9 cm)
Note: If unit is installed deeper than 24” (61.0 cm),then shim
behind the mounting board by the difference.
Bottom of anti-tip board is 3-7/8” (9.8 cm) below opening height.
Note: Top of unit must be placed firmly underanti-tip board.
Anti-tip location
79-3/8”
(201.6 cm) min.
to bottom of
anti-tip board
80-1/2”
(204.6 cm) max.
to bottom of
anti-tip board
29”
(73.7 cm)
3-1/2”
(8.9 cm)
1-1/2”
(3.8 cm)
Anti-Tip Dimensions (Bottom Mount)
36” Bottom Mount

Reverse dimensions
for other end.
1/2”
(1.27 cm)
1-1/2”
(3.81cm)
1/4” Radius
(.64 cm)
2-3/4”
(6.98 cm)
1/2”
(1.27cm)
3/4”
(1.90cm)
1/2”
(1.27cm)
1/8”
(.31 cm)
1/2”
(1.27 cm)
1/4” Radius 1/4” Radius
(1.2 cm)
(1.2 cm)
1/4” Radius
(.64 cm)
7/8”
(2.22 cm)
1/2”
(1.27 cm)
34”
(86.36 cm)
34”
(86.36 cm)
3/4”
(1.90 cm)
1/2”
(1.27 cm)
3/4”
(1.90 cm)
3-3/4”
(9.52 cm)
3-3/4”
(9.52 cm)
3-5/8”
(9.20 cm)
33-15/16”
(86.20 cm)
3”
(7.62 cm)
3”
(7.62 cm)
3/4”
(1.90 cm)
35-1/2”
(90.17 cm)
1/2”
(1.27 cm)
3-1/8”
(7.93 cm)
Optional hinge cover
32-3/16”
(81.75 cm)
5-17/32”
(14.10 cm)
4-11/64”
(10.59 cm)
30-27/32”
(78.34 cm)
3 25/32”
(9.60 cm)
27/32”
(.84 cm)
9/16”
(1.42 cm)
1/4”
(.635 cm)
16.5˚
20.0˚
Custom Grille Dimensions (Bottom Mount)
7
35-1/4”
(89.5 cm)
23-1/16”
(58.6 cm)
3/4”
(1.9 cm)
35-1/4”
(89.5 cm)
34-3/8” to notch
(86.6 cm)
7/8”
(2.2 cm)
5/8”
(1.6 cm)
51-7/8”
(131.8 cm)
51-1/4”
(130.2 cm)
3/4”
(1.9 cm)
Note: Corner notch is for left
hinge door. (Reverse for right hinge)
See page 50 for cutout instructions
7/8”
(2.2cm)
5/8”
(1.6 cm)
1/8”
(0.3 cm)
2”
(5.1 cm)
For Models made
before 9/22/06
Note: Inset shown upside down.
1-13/16”
(4.60 cm)
5/8”
5/8”
(1.6 cm)
(1.6 cm)
3”
(7.62 cm)
3/32”
(.24 cm)
5/8”
5/8”
(1.6 cm)
For Models made
after 9/22/06
Note: Inset shown upside down
Overlay Dimensions (Bottom Mount)
6
36” Custom Panels 36” Custom Grille
Note: Panel overlays must be dry, solid, straight one
piece panels. The use of multiple panel pieces to
achieve the dimensions is not recommended.
Note: If 1/4” back panel is used, the dimensions are
1/4” smaller than the dimensions shown on the top, left
and right side. At the bottom, the 1/4” back panel
should be 5/8” smaller than the dimensions shown.

75-15/16”
(192.9 cm)
3-1/2”
(8.9 cm)
82-7/8”
(210.5 cm)
min.
to
84-1/16”
(213.5 cm)
max.
Measurement varies
(locally supplied hardware)
23-13/16”
(60.5 cm)
24-3/4”
(62.9 cm)
41”
(104.1 cm)
42”
(106.7 cm)
Dimensions (Side-By-Side)
9
3 25/32”
(9.60 cm)
27/32”
(.84 cm)
9/16”
(1.42 cm)
1/4”
(.635 cm)
16.5˚
20.0˚
Note: This part should be
locatedat the center of the
grille. If desired, twoper grille
canbe used by dividing the
length of the grille into thirds.
1/2”
(1.27cm)
1-1/2”
(3.81 cm)
1/4” Radius
(.64 cm)
2-3/4”
(6.98 cm)
1/2”
(1.27cm)
3/4”
(1.90 cm)
3/8”
(0.38 cm)
1/2”
(1.27 cm)
R 3/32”
(0.09 cm)
3/4”
(1.90 cm)
3/4”
(1.90 cm)
3/4”
(1.90 cm)
13/32”
(1.03 cm)
9/16”
(1.43 cm)
1/8”
(.32 cm)
Grillesupport
2-7/8”
(7.30 cm)
1”
(2.54 cm)
1/2”
(1.27 cm)
1/8”
(.31 cm)
1/2”
(1.27 cm)
1/4” Radius1/4” Radius
(1.2 cm) (1.2 cm)
1/4” Radius
(.64 cm)
Reverse dimensions
for other end.
7/8”
(2.22 cm)
1/2”
(1.27 cm)
1/2”
(1.27 cm)
3-1/8”
(7.93 cm)
Optional hinge cover
1/2”
(1.27 cm)
3-5/8”
(9.20 cm)
3/4”
(1.90 cm)
3/4”
(1.90 cm)
3-3/4”
(9.52 cm)
3-3/4”
(9.52 cm)
3”
(7.62 cm)
3”
(7.62 cm)
3/4”
(1.90 cm)
71-1/2”
(181.61 cm)
70”
(177.80 cm
69-15/16”
(177.64 cm)
70”
(177.80 cm)
68-3/64”
(172.83 cm)
66-27/32”
(169.78 cm)
4-11/64”
(11.27 cm)
5-17/32”
(14.04 cm)
30-27/32”
(78.34 cm)
32-3/16”
(81.75 cm)
40-11/64”
(102.03 cm)
41-25/64”
(10 5.13 cm)
Custom Grille Dimensions (Bottom Mount)
8
Dual 36” Custom Grille
42” Side-By-Side