Viking RDDFF236SS User manual

Viking Range Corporation
111 Front Street
Greenwood, Mississippi 38930 USA
(662) 55-1200
For product information,
call 1-888-VIKING1 (8 5- 6 1)
or visit the Viking Web site at
vikingrange.com
F21022 EN (051712)
Viking In tallation Guide
Free tanding Refrigeration Side Trim,
Side Panel, Top Panel & Grille In tallation-
French Door Bottom-Mount (236 Serie )

3
3
4
B
Apply adhesive tape to grille assembly.
2
Remove screws and hold for replacement. Discard
hinge covers. Use hinge covers provided in kit.
Remove edge and top of corner cover.
1
2
Installation - Side Trim and Grille
(Built-In Installation)
Attach brackets and spacers, included in the kit, to the
grille assembly with four B screws.
5
1
2
Remove adhesive backing. Firmly press the grille
assembly down so the adhesive adheres to the cabinet.
Align grille assembly to front door and position grille
on top of unit.
Freestanding Refrigerators
Description VCFF/RDDFF236 with side panels/tops/grilles
Overall width with side panels 35-7/8” (91.1 cm)
Overall height with tops/grilles 73-5/8” (187.0 cm)
Cutout width with side panels 36” (91. cm)
Cutout height with tops/grilles 73-3/ ” (187.3 cm)
Specifications
Required Components - Built-In Installation
Left Shim
Trim
Right Shim
Trim
Left Side
Trim
Right Side
Trim
Adhesive
Tape
AB
Screws
Brackets
Right
Spacer
Left
Spacer
Left Hinge
Cover
Right Hinge
Cover
Grille
6
A
Secure the grille brackets to the holes in the hinge
plate with two A screws. Once grille assembly is secure,
install hinge cover screws back into new hinge covers.
Some movement of hinge covers might be needed for
mounting brackets to fit.

5
Installation - Side Trim and Grille
(Built-In Installation) (cont.)
Raise the unit up until the measurement from the floor
to the top of the grille assembly is 73-3/ inches.
7
73-3/4”
(187.3cm)
Shim trim has adhesive backing on both sides. Remove
adhesive backing on refrigerator side only. Fit the shim
trim to the front of the unit first. With center hinge, the
shim trim will have a cutout. Use the cutout to locate
the height of the shim trim.
8
2
2
1
Remove adhesive backing for the side trim. Locate the
top of the side trim with the top of the grille assembly.
Press the side trim into the refrigerator cabinet at the
center location.
9
2
2
1
complete
Installation - Side Panel, Top Panel and Grille
(Wrapped Installation)
Required Components - Wrapped Installation
Front Grille
B
A
Cap Cover
Left Side
Panel
Right Side
Panel Top
Panel
Screws

76
Installation - Side Panel, Top Panel and Grille
(Wrapped Installation) (cont.)
Remove adhesive backing from other side panel. Fit the
side panel to the front of the unit first. Spacer on top of
side panel needs to sit on top of refrigerator cabinet.
6
1
2
2
Pull the machine cover and slip back of side panel
between refrigerator cabinet and machine cover. Install
machine cover screws back into refrigerator cabinet.
NOTE: The holes on the side panel are clearance holes.
7
8
Install machine cover screws back into
refrigerator cabinet.
NOTE: The holes on the side panel are clearance holes.
A
10
11
Insert six A screws through holes of top panel into side
panel.
Insert cap covers into holes.
complete
9
Align top panel and grille assembly to front door and
position top panel and grille on top of unit. Flanges
must fit into gap.
Pull the machine cover off and slip back of side panel
between refrigerator cabinet and machine cover. Install
machine cover screws back into refrigerator cabinet.
NOTE: The holes on the side panel are clearance holes.
5
Remove adhesive backing from the side panel. Fit the
side panel to the front of the unit first. With a center
hinge, the side panel will have a cutout.
4
2
1
3
Remove screws on lower back machine cover.
Hold for replacement.
B
2
With top panel and grille upside down, position grille
assembly in front of top panel. Secure top panel to
grille assembly via four outer holes (B screws) and use
existing for inner holes.
Remove edge and top of corner cover.
1