Vimar ELVOX TVCC 46235.015B User manual

Viale Vicenza, 14
36063 Marostica VI - Italy
www.vimar.com
49401710A0 00 2105
46235.015B
Telecamera
Camera
Istruzioni per l’uso
Quick start guide
Dima di foratura
Drill template
Viti e tasselli
Screws and Plastic plug
Installazione scheda SD e collegamento dell’alimentazione
Installare la scheda di archiviazione:
1 - Allentare le viti di ssaggio del coperchio posteriore come illustrato di seguito
(Fig. 1).
2 - Inserire la scheda SD nello slot della scheda di archiviazione (Fig. 2).
3 - Rimontare e ssare il coperchio posteriore.
Installazione telecamera
Prima di iniziare, assicurarsi che la parete sia su󰀩cientemente solida
per sopportare il peso della telecamera. Installare la telecamera
in ambiente asciutto. La procedura di montaggio è la seguente:
1- Passare i cavi attraverso la sta󰀨a. Montare la speed dome sulla sta󰀨a (Fig. 3).
2- Fissare la speed dome alla sta󰀨a con le viti (Fig. 4)
3- Utilizzare la dima di foratura per praticare i fori per le viti sulla parete (Fig. 5).
4- Allineare le due viti ai fori indicati dalle frecce e lasciare circa 12 mm dal muro
(Fig. 6)
5- Collegare i cavi e quindi appendere la sta󰀨a al muro e ssarla (Fig. 7-8).
Introduzione
Questa telecamera IP Speed Dome è stata progettata per fornire soluzioni TVCC
ad elevate prestazioni. Adotta chip di elaborazione video allo stato dell'arte. Utilizza
le tecnologie più avanzate di codica e decodica video ed è conforme al protocollo
TCP/IP, SoC (System on Chip) per assicurare la stabilità e l'a󰀩dabilità del sistema.
I manuali completi e i software CVM, Iptool.exe e Diskcalculator.exe sono disponi-
bili nella scheda prodotto consultabile nel sito www.vimar.com
Connessioni
Di seguito sono riportate le principali connessioni della telecamera.
Introduction
This Speed Dome IP-camera is designed for high performance CCTV solutions. It
adopts state of the art video processing chips. It utilizes most advanced technolo-
gies, such as video encoding and decoding technology, complies with theTCP/IP
protocol, SoC (System on chip), etc to ensure this system more stable and reliable.
Complete manuals and CVM, Iptool.exe e Diskcalculator.exe software are available
to download in the Product info sheet section of www.vimar.com website.
Connections
Here below the main connections of the camera
Install SD Card and Power Connection
Install Storage Card:
1 - Loosen the xed screws of the rear as shown below (Fig. 1).
2 - Insert the SD card into the storage card slot (Fig. 2).
3 - Install back the cover back.
Camera Installation
Before start, please make sure that the wall is strong enough to withstand
the weight of the camera. Please install the camera in the dry environment. The
mounting steps are as follows:
1- Pull the cables through the bracket. Mount the speed dome to the bracket (Fig.
3).
2- Secure the speed dome to the bracket with the screws (Fig. 4).
3- Drill the screw holes on the wall according to the drill template (Fig. 5).
4- Drive the two screws to the holes indicated by the arrows and leave 12mm
clearance (Fig. 6).
5- Connect the cables and then hang the bracket on the wall and x it (Fig. 7-8).
Overview
Installation
Cable Connection
1
2
3
Network Cable
2
1
Quick Start Guide
HD PTZ Camera
■ Please read this instruction carefully before using the product
and keep it for further reference.
■ All the examples and pictures used here are for reference only.
■ The contents of this manual are subject to change without
notice.
► Connecting Network Cable
1 Ethernet connector
2
3 Safety wire
Power connector
1
2
3
DC12V
① Loosen the nut from the main element.
② Run the network cable (without RJ 45 connector) through the
both elements. Then crimp the cable with RJ 45 connector.
③ Connect the cable to the hermetic connector. Then tighten the
nut and the main cover.
3
Micro SD Card Installation
Please make sure the wall is strong enough to bear the dome
camera’s weigh and the camera is powered off during
installation.
This PTZ camera supports wall or ceiling mounting. Please select
a way to install as needed. The following instructions are for
reference only.
Insert a micro
SD card
1. Loosen the four screws of
the cover and then remove
the cover.
2. Insert a micro SD card as indicated
above and then install the cover back.
Wall Mounting
1. Pull the cables through the
bracket.
3. Drill the screw holes on the wall
according to the drill template. Then
insert the plastic plugs into the holes.
4. Insert two screws to the holes
as indicated by the arrows (left)
and leave 12mm clearance.
5. Connect the cables and then
hang the bracket on the wall.
6. Attach the bracket to the wall
with four screws.
2. Secure the PTZ camera to the
bracket with screws.
12
Overview
Installation
Cable Connection
1
2
3
Network Cable
2
1
Quick Star t Guide
HD PTZ Camera
■ Please read this instruction carefully before using the product
and keep it for further reference.
■ All the examples and pictures used here are for reference only.
■ The contents of this manual are subject to change without
notice.
► Connecting Network Cable
1 Ethernet connector
2
3 Safety wire
Power connector
1
2
3
DC12V
① Loosen the nut from the main element.
② Run the network cable (without RJ 45 connector) through the
both elements. Then crimp the cable with RJ 45 connector.
③ Connect the cable to the hermetic connector. Then tighten the
nut and the main cover.
3
Micro SD Card Installation
Please make sure the wall is strong enough to bear the dome
camera’s weigh and the camera is powered off during
installation.
This PTZ camera supports wall or ceiling mounting. Please select
a way to install as needed. The following instructions are for
reference only.
Insert a micro
SD card
1. Loosen the four screws of
the cover and then remove
the cover.
2. Insert a micro SD card as indicated
above and then install the cover back.
Wall Mounting
1. Pull the cables through the
bracket.
3. Drill the screw holes on the wall
according to the drill template. Then
insert the plastic plugs into the holes.
4. Insert two screws to the holes
as indicated by the arrows (left)
and leave 12mm clearance.
5. Connect the cables and then
hang the bracket on the wall.
6. Attach the bracket to the wall
with four screws.
2. Secure the PTZ camera to the
bracket with screws.
12
1 Connettore Ethernet /
Ethernet Connector
2 Connettore di
alimentazione/ Power
Connector
3 Filo di sicurezza / Safety
wire
Overview
Installation
Cable Connection
1
2
3
Network Cable
2
1
Quick Start Guide
HD PTZ Camera
■ Please read this instruction carefully before using the product
and keep it for further reference.
■ All the examples and pictures used here are for reference only.
■ The contents of this manual are subject to change without
notice.
► Connecting Network Cable
1 Ethernet connector
2
3 Safety wire
Power connector
1
2
3
DC12V
① Loosen the nut from the main element.
② Run the network cable (without RJ 45 connector) through the
both elements. Then crimp the cable with RJ 45 connector.
③ Connect the cable to the hermetic connector. Then tighten the
nut and the main cover.
3
Micro SD Card Installation
Please make sure the wall is strong enough to bear the dome
camera’s weigh and the camera is powered off during
installation.
This PTZ camera supports wall or ceiling mounting. Please select
a way to install as needed. The following instructions are for
reference only.
Insert a micro
SD card
1. Loosen the four screws of
the cover and then remove
the cover.
2. Insert a micro SD card as indicated
above and then install the cover back.
Wall Mounting
1. Pull the cables through the
bracket.
3. Drill the screw holes on the wall
according to the drill template. Then
insert the plastic plugs into the holes.
4. Insert two screws to the holes
as indicated by the arrows (left)
and leave 12mm clearance.
5. Connect the cables and then
hang the bracket on the wall.
6. Attach the bracket to the wall
with four screws.
2. Secure the PTZ camera to the
bracket with screws.
12
Package
Overview
Installation
1
2
3
4
① Loosen the nut from the main element.
② Run the network cable (without RJ 45 connector) through the
both elements. Then crimp the cable with RJ 45 connector.
③ Connect the cable to the Ethernet connector. Then tighten the
nut and the main cover.
Warning and Caution
■ If the product does not work properly, please contact your dealer
or the nearest service center. Never attempt to disassemble the
camera yourself. (We shall not be responsible for any problems
caused by unauthorized repair or maintenance.)
■ Do not allow water or liquid intrusion into the camera.
■ In the use of the product, you must be strict compliance with the
electrical safety regulations of the nation and region. When the
product is mounted on wall or ceiling, the device shall be firmly
fixed.
■ Do not use camera beyond specified voltage range.
■ Do not drop the camera or subject it to physical shock.
■ The grounding hole of the product is recommended to be
grounded to further enhance the reliability of the camera.
■ Avoid touching the camera lens.
■ If cleaning is necessary, please use clean cloth to wipe it gently.
■ Do not aim the camera at the sun or extra bright place.
■ Do not place the camera in extremely hot, cold, dusty or damp
locations, and do not expose it to high electromagnetic radiation.
■ To avoid heat accumulation, good ventilation is required for
operating environment.
Quick Start Guide
Panoramic Bullet
Network Camera
Camera Quick start guide
CD Plastic plug ×4
Drill template
Screwdriver Rubber plug
4 tapping screws
● Connecting Alarm Input/Output
■ Please read this instruction carefully before using the product
and keep it for further reference.
■ All the examples and pictures used here are for reference only.
■ The contents of this manual are subject to change without
notice.
2
13
1 Ethernet Connector *
2 Audio Input (MIC)
3 Audio Output (HP)
4 Alarm Input/Output
5 RS485
6 Power Connector *
7 Ground
8 Reset
9 Micro SD Card Slot
* 1
* 2 This camera can be powered by DC 12V/PoE power supply. If the PoE switch
is used to power the camera, DC12V power supply is not required.
It is recommended to install the security cap for outdoor installation.
Security cap
Ground
1
3
4
5
6
7
89
2
ALARM
4 3 2 1
R 485
S
+
ALARM
4 3 2 1
R 485
S
+
1--ALM-COM
2--ALM-OPEN
3--ALM-INA
4--ALM-GND
RS485T+
RS485T-
Please make sure that the wall or ceiling is strong enough to
withstand 3 times the weight of the camera.
① Open the cover of the camera and then insert a micro SD card.
Then install back this cover and fix it firmly with the screws (please
keep it flat when installing).
● Connecting Network Cable
Alarm
Power Source
IPC
ALARM-COM
ALARM-OPEN
Alarm Input
Alarm Output
+
+
--
Sensor
IPC
ALARM-INA
ALARM-GND
3
4
1
2
Overview
Installation
Cable Connection
1
2
3
Network Cable
2
1
Quick Star t Guide
HD PTZ Camera
■ Please read this instruction carefully before using the product
and keep it for further reference.
■ All the examples and pictures used here are for reference only.
■ The contents of this manual are subject to change without
notice.
► Connecting Network Cable
1 Ethernet connector
2
3 Safety wire
Power connector
1
2
3
DC12V
① Loosen the nut from the main element.
② Run the network cable (without RJ 45 connector) through the
both elements. Then crimp the cable with RJ 45 connector.
③ Connect the cable to the hermetic connector. Then tighten the
nut and the main cover.
3
Micro SD Card Installation
Please make sure the wall is strong enough to bear the dome
camera’s weigh and the camera is powered off during
installation.
This PTZ camera supports wall or ceiling mounting. Please select
a way to install as needed. The following instructions are for
reference only.
Insert a micro
SD card
1. Loosen the four screws of
the cover and then remove
the cover.
2. Insert a micro SD card as indicated
above and then install the cover back.
Wall Mounting
1. Pull the cables through the
bracket.
3. Drill the screw holes on the wall
according to the drill template. Then
insert the plastic plugs into the holes.
4. Insert two screws to the holes
as indicated by the arrows (left)
and leave 12mm clearance.
5. Connect the cables and then
hang the bracket on the wall.
6. Attach the bracket to the wall
with four screws.
2. Secure the PTZ camera to the
bracket with screws.
12
Telecamera Speed Dome IP 2Mpx (1920 × 1080), sensore CMOS 1/2,8in, obiettivo
5 ~ 75 mm, ltro IR meccanico, zoom ottico 15x, illuminatori IR con portata no a
150m, slot SD CARD 256GB, funzioni di analisi video, WDR, BLC, Defog e 3DNR,
RTSP, alimentazione PoE+ (IEEE 802.3at) o 12 Vdc max 22 W, completa di sta󰀨a
da parete, grado di protezione IP66. Dimensioni senza sta󰀨a ø 173x247 mm. Peso
2100 g.
Speed Dome IP 2Mpx camera (1920 × 1080), 1/2.8in CMOS sensor, 5~75 mm
lens, mechanical IR lter, 15x optical zoom, IR illuminators with a capacity of up
to 150m, 256GB SD CARD slots, video analysis functions, WDR, BLC, Defog and
3DNR, RTSP, PoE+ power supply (IEEE 802.3at) or 12 Vdc max 22 W, complete
with wall bracket, IP66 protection degree. Dimensions without bracket ø 173x247
mm. Weight 2100 g.
Contenuto della confezione
Una volta ricevuto il dispositivo, controllare gli accessori indicati di seguito. Le illu-
strazioni sotto riportate hanno solo funzione di riferimento. Far riferimento all'appa-
recchiatura in dotazione.
Package content
After you receive your device, please check the following accessories. The pictures
here are for reference only.
Overview
Installation
Cable Connection
1
2
3
Network Cable
2
1
Quick Start Guide
HD PTZ Camera
■ Please read this instruction carefully before using the product
and keep it for further reference.
■ All the examples and pictures used here are for reference only.
■ The contents of this manual are subject to change without
notice.
► Connecting Network Cable
1 Ethernet connector
2
3 Safety wire
Power connector
1
2
3
DC12V
① Loosen the nut from the main element.
② Run the network cable (without RJ 45 connector) through the
both elements. Then crimp the cable with RJ 45 connector.
③ Connect the cable to the hermetic connector. Then tighten the
nut and the main cover.
3
Micro SD Card Installation
Please make sure the wall is strong enough to bear the dome
camera’s weigh and the camera is powered off during
installation.
This PTZ camera supports wall or ceiling mounting. Please select
a way to install as needed. The following instructions are for
reference only.
Insert a micro
SD card
1. Loosen the four screws of
the cover and then remove
the cover.
2. Insert a micro SD card as indicated
above and then install the cover back.
Wall Mounting
1. Pull the cables through the
bracket.
3. Drill the screw holes on the wall
according to the drill template. Then
insert the plastic plugs into the holes.
4. Insert two screws to the holes
as indicated by the arrows (left)
and leave 12mm clearance.
5. Connect the cables and then
hang the bracket on the wall.
6. Attach the bracket to the wall
with four screws.
2. Secure the PTZ camera to the
bracket with screws.
12

Viale Vicenza, 14
36063 Marostica VI - Italy
www.vimar.com
49401710A0 00 2105
46235.015B
ENIT
Overview
Installation
Cable Connection
1
2
3
Network Cable
2
1
Quick Start Guide
HD PTZ Camera
■ Please read this instruction carefully before using the product
and keep it for further reference.
■ All the examples and pictures used here are for reference only.
■ The contents of this manual are subject to change without
notice.
► Connecting Network Cable
1 Ethernet connector
2
3 Safety wire
Power connector
1
2
3
DC12V
① Loosen the nut from the main element.
② Run the network cable (without RJ 45 connector) through the
both elements. Then crimp the cable with RJ 45 connector.
③ Connect the cable to the hermetic connector. Then tighten the
nut and the main cover.
3
Micro SD Card Installation
Please make sure the wall is strong enough to bear the dome
camera’s weigh and the camera is powered off during
installation.
This PTZ camera supports wall or ceiling mounting. Please select
a way to install as needed. The following instructions are for
reference only.
Insert a micro
SD card
1. Loosen the four screws of
the cover and then remove
the cover.
2. Insert a micro SD card as indicated
above and then install the cover back.
Wall Mounting
1. Pull the cables through the
bracket.
3. Drill the screw holes on the wall
according to the drill template. Then
insert the plastic plugs into the holes.
4. Insert two screws to the holes
as indicated by the arrows (left)
and leave 12mm clearance.
5. Connect the cables and then
hang the bracket on the wall.
6. Attach the bracket to the wall
with four screws.
2. Secure the PTZ camera to the
bracket with screws.
12
Overview
Installation
Cable Connection
1
2
3
Network Cable
2
1
Quick Start Guide
HD PTZ Camera
■ Please read this instruction carefully before using the product
and keep it for further reference.
■ All the examples and pictures used here are for reference only.
■ The contents of this manual are subject to change without
notice.
► Connecting Network Cable
1 Ethernet connector
2
3 Safety wire
Power connector
1
2
3
DC12V
① Loosen the nut from the main element.
② Run the network cable (without RJ 45 connector) through the
both elements. Then crimp the cable with RJ 45 connector.
③ Connect the cable to the hermetic connector. Then tighten the
nut and the main cover.
3
Micro SD Card Installation
Please make sure the wall is strong enough to bear the dome
camera’s weigh and the camera is powered off during
installation.
This PTZ camera supports wall or ceiling mounting. Please select
a way to install as needed. The following instructions are for
reference only.
Insert a micro
SD card
1. Loosen the four screws of
the cover and then remove
the cover.
2. Insert a micro SD card as indicated
above and then install the cover back.
Wall Mounting
1. Pull the cables through the
bracket.
3. Drill the screw holes on the wall
according to the drill template. Then
insert the plastic plugs into the holes.
4. Insert two screws to the holes
as indicated by the arrows (left)
and leave 12mm clearance.
5. Connect the cables and then
hang the bracket on the wall.
6. Attach the bracket to the wall
with four screws.
2. Secure the PTZ camera to the
bracket with screws.
12
Overview
Installation
Cable Connection
1
2
3
Network Cable
2
1
Quick Start Guide
HD PTZ Camera
■ Please read this instruction carefully before using the product
and keep it for further reference.
■ All the examples and pictures used here are for reference only.
■ The contents of this manual are subject to change without
notice.
► Connecting Network Cable
1 Ethernet connector
2
3 Safety wire
Power connector
1
2
3
DC12V
① Loosen the nut from the main element.
② Run the network cable (without RJ 45 connector) through the
both elements. Then crimp the cable with RJ 45 connector.
③ Connect the cable to the hermetic connector. Then tighten the
nut and the main cover.
3
Micro SD Card Installation
Please make sure the wall is strong enough to bear the dome
camera’s weigh and the camera is powered off during
installation.
This PTZ camera supports wall or ceiling mounting. Please select
a way to install as needed. The following instructions are for
reference only.
Insert a micro
SD card
1. Loosen the four screws of
the cover and then remove
the cover.
2. Insert a micro SD card as indicated
above and then install the cover back.
Wall Mounting
1. Pull the cables through the
bracket.
3. Drill the screw holes on the wall
according to the drill template. Then
insert the plastic plugs into the holes.
4. Insert two screws to the holes
as indicated by the arrows (left)
and leave 12mm clearance.
5. Connect the cables and then
hang the bracket on the wall.
6. Attach the bracket to the wall
with four screws.
2. Secure the PTZ camera to the
bracket with screws.
12
Overview
Installation
Cable Connection
1
2
3
Network Cable
2
1
Quick Start Guide
HD PTZ Camera
■ Please read this instruction carefully before using the product
and keep it for further reference.
■ All the examples and pictures used here are for reference only.
■ The contents of this manual are subject to change without
notice.
► Connecting Network Cable
1 Ethernet connector
2
3 Safety wire
Power connector
1
2
3
DC12V
① Loosen the nut from the main element.
② Run the network cable (without RJ 45 connector) through the
both elements. Then crimp the cable with RJ 45 connector.
③ Connect the cable to the hermetic connector. Then tighten the
nut and the main cover.
3
Micro SD Card Installation
Please make sure the wall is strong enough to bear the dome
camera’s weigh and the camera is powered off during
installation.
This PTZ camera supports wall or ceiling mounting. Please select
a way to install as needed. The following instructions are for
reference only.
Insert a micro
SD card
1. Loosen the four screws of
the cover and then remove
the cover.
2. Insert a micro SD card as indicated
above and then install the cover back.
Wall Mounting
1. Pull the cables through the
bracket.
3. Drill the screw holes on the wall
according to the drill template. Then
insert the plastic plugs into the holes.
4. Insert two screws to the holes
as indicated by the arrows (left)
and leave 12mm clearance.
5. Connect the cables and then
hang the bracket on the wall.
6. Attach the bracket to the wall
with four screws.
2. Secure the PTZ camera to the
bracket with screws.
12
Overview
Installation
Cable Connection
1
2
3
Network Cable
2
1
Quick Start Guide
HD PTZ Camera
■ Please read this instruction carefully before using the product
and keep it for further reference.
■ All the examples and pictures used here are for reference only.
■ The contents of this manual are subject to change without
notice.
► Connecting Network Cable
1 Ethernet connector
2
3 Safety wire
Power connector
1
2
3
DC12V
① Loosen the nut from the main element.
② Run the network cable (without RJ 45 connector) through the
both elements. Then crimp the cable with RJ 45 connector.
③ Connect the cable to the hermetic connector. Then tighten the
nut and the main cover.
3
Micro SD Card Installation
Please make sure the wall is strong enough to bear the dome
camera’s weigh and the camera is powered off during
installation.
This PTZ camera supports wall or ceiling mounting. Please select
a way to install as needed. The following instructions are for
reference only.
Insert a micro
SD card
1. Loosen the four screws of
the cover and then remove
the cover.
2. Insert a micro SD card as indicated
above and then install the cover back.
Wall Mounting
1. Pull the cables through the
bracket.
3. Drill the screw holes on the wall
according to the drill template. Then
insert the plastic plugs into the holes.
4. Insert two screws to the holes
as indicated by the arrows (left)
and leave 12mm clearance.
5. Connect the cables and then
hang the bracket on the wall.
6. Attach the bracket to the wall
with four screws.
2. Secure the PTZ camera to the
bracket with screws.
12
Overview
Installation
Cable Connection
1
2
3
Network Cable
2
1
Quick Start Guide
HD PTZ Camera
■ Please read this instruction carefully before using the product
and keep it for further reference.
■ All the examples and pictures used here are for reference only.
■ The contents of this manual are subject to change without
notice.
► Connecting Network Cable
1 Ethernet connector
2
3 Safety wire
Power connector
1
2
3
DC12V
① Loosen the nut from the main element.
② Run the network cable (without RJ 45 connector) through the
both elements. Then crimp the cable with RJ 45 connector.
③ Connect the cable to the hermetic connector. Then tighten the
nut and the main cover.
3
Micro SD Card Installation
Please make sure the wall is strong enough to bear the dome
camera’s weigh and the camera is powered off during
installation.
This PTZ camera supports wall or ceiling mounting. Please select
a way to install as needed. The following instructions are for
reference only.
Insert a micro
SD card
1. Loosen the four screws of
the cover and then remove
the cover.
2. Insert a micro SD card as indicated
above and then install the cover back.
Wall Mounting
1. Pull the cables through the
bracket.
3. Drill the screw holes on the wall
according to the drill template. Then
insert the plastic plugs into the holes.
4. Insert two screws to the holes
as indicated by the arrows (left)
and leave 12mm clearance.
5. Connect the cables and then
hang the bracket on the wall.
6. Attach the bracket to the wall
with four screws.
2. Secure the PTZ camera to the
bracket with screws.
12
Fig. 1 Fig. 2 Fig. 3
Fig. 4
Fig. 5 Fig. 6 Fig. 7 Fig. 8
Overview
Installation
Cable Connection
1
2
3
Network Cable
2
1
Quick Start Guide
HD PTZ Camera
■ Please read this instruction carefully before using the product
and keep it for further reference.
■ All the examples and pictures used here are for reference only.
■ The contents of this manual are subject to change without
notice.
► Connecting Network Cable
1 Ethernet connector
2
3 Safety wire
Power connector
1
2
3
DC12V
① Loosen the nut from the main element.
② Run the network cable (without RJ 45 connector) through the
both elements. Then crimp the cable with RJ 45 connector.
③ Connect the cable to the hermetic connector. Then tighten the
nut and the main cover.
3
Micro SD Card Installation
Please make sure the wall is strong enough to bear the dome
camera’s weigh and the camera is powered off during
installation.
This PTZ camera supports wall or ceiling mounting. Please select
a way to install as needed. The following instructions are for
reference only.
Insert a micro
SD card
1. Loosen the four screws of
the cover and then remove
the cover.
2. Insert a micro SD card as indicated
above and then install the cover back.
Wall Mounting
1. Pull the cables through the
bracket.
3. Drill the screw holes on the wall
according to the drill template. Then
insert the plastic plugs into the holes.
4. Insert two screws to the holes
as indicated by the arrows (left)
and leave 12mm clearance.
5. Connect the cables and then
hang the bracket on the wall.
6. Attach the bracket to the wall
with four screws.
2. Secure the PTZ camera to the
bracket with screws.
12
Inserire la scheda SD
Insert SD card
Connessione alla rete Ethernet
Come esempio, accediamo alla telecamera IP attraverso la LAN. In una LAN è
possibile accedere in due modi:
1. Accesso tramite IP-Tool
2. Accesso diretto tramite Internet Explorer
Accesso alla telecamera tramite IP-Tool
1) Assicurarsi che la telecamera e il PC siano connessi alla LAN.
2) Eseguire il download di IP-Tool dalla sezione prodotto del sito www.vimar.com e
installarlo sul computer. Inne, avviare IP-Tool come mostrato di seguito.
3) Modicare l'indirizzo IP. L'indirizzo IP predenito
di questa telecamera è 192.168.226.201. Fare
click sulle informazioni della telecamera elenca-
te nella tabella sopra riportata per visualizzare
le informazioni di rete sulla destra. Modicare
l'indirizzo IP e il gateway della telecamera e
assicurarsi che l'indirizzo di rete si trovi nello
stesso segmento della rete locale del computer.
Modicare l'indirizzo IP del dispositivo in base
alla situazione specica.
Network Connections
Here we take accessing IP camera via LAN for example. In LAN, there
are two ways to access.
1. Access through IP-Tool
2. Directly Access through IE Browser
Access the camera through IP-Tool
1) Make sure that the camera and the PC are well connected to the LAN.
2) download IP-Tool Product info sheet section of www.vimar.com website and then
install it in the computer. After that, run the IP-Tool as shown below.
3) Modify the IP address. The default IP address
of this camera is 192.168.226.201. Click the
information of the camera listed in the above ta-
ble to show the network information on the right
hand. Modify the IP address and gateway of the
camera and make sure its network address is
in the same local network segment as the com-
puter’s. Please modify the IP address of your
device according to the practical situation
Overview
Installation
Cable Connection
1
2
3
Network Cable
2
1
Quick Start Guide
HD PTZ Camera
■ Please read this instruction carefully before using the product
and keep it for further reference.
■ All the examples and pictures used here are for reference only.
■ The contents of this manual are subject to change without
notice.
► Connecting Network Cable
1 Ethernet connector
2
3 Safety wire
Power connector
1
2
3
DC12V
① Loosen the nut from the main element.
② Run the network cable (without RJ 45 connector) through the
both elements. Then crimp the cable with RJ 45 connector.
③ Connect the cable to the hermetic connector. Then tighten the
nut and the main cover.
3
Micro SD Card Installation
Please make sure the wall is strong enough to bear the dome
camera’s weigh and the camera is powered off during
installation.
This PTZ camera supports wall or ceiling mounting. Please select
a way to install as needed. The following instructions are for
reference only.
Insert a micro
SD card
1. Loosen the four screws of
the cover and then remove
the cover.
2. Insert a micro SD card as indicated
above and then install the cover back.
Wall Mounting
1. Pull the cables through the
bracket.
3. Drill the screw holes on the wall
according to the drill template. Then
insert the plastic plugs into the holes.
4. Insert two screws to the holes
as indicated by the arrows (left)
and leave 12mm clearance.
5. Connect the cables and then
hang the bracket on the wall.
6. Attach the bracket to the wall
with four screws.
2. Secure the PTZ camera to the
bracket with screws.
12
12

Viale Vicenza, 14
36063 Marostica VI - Italy
www.vimar.com
49401710A0 00 2105
46235.015B
Speciche/ Specications
46235.015B
Telecamera
Cam
Sensore/Sensor 1/2,8" CMOS Scansione Progressiva 2 Mpixel
Pixel immagine/Pixel image 1920 X 1080
Sensibilità/ Sensitivity Color: [email protected],AGC ON - B/W: 0.001Lux @F1.6 AGC ON - 0 lux IR Led ON
Obiettivo/Lens Zoom ottico 15X (5 - 75 mm) - Optic zoom 15X (5 - 75 mm)
Angolo di visione / Vision corner 54° Wide - 4° Tele
Immagine
Image
Compressione Video/Video compression H264 - H265 - MJPEG
Bit Rate 64Kbs ~ 4Mbs
Frame rate primario
Primary frame rate
Frame rate secondario
Secondary frame rate
30 Fps (1920X1080)
30 Fps (1280X720)
30 Fps (1280X720)
30 Fps (704x576)
30 Fps (480x240)
30 Fps (352x288)
Codica/ Codication VBR/CBR
Qualità/Quality Livello VBR 5, CBR illimitato - unlimited
Connessioni
Connections
Network RJ45 10/100M
Uscita Video CVBS/CVBS video output No
SD card Si non inclusa - Yes not included (256 GB MAX)
RS485 No
Audio In / out 0/0
Allarme / Alarm In / out 0/0
Funzioni
Functions
Funzioni/Functions WDR 120dB, Defog, BLC, HLC, 3D DNR, Smart tracking
Analisi Video Intelligente /
Intelligent Video Analysis
Rilevamento e riconoscimento volti (max 15 volti /sec) - Attraversamento linea, intrusione area, anomalia ,
conteggio veicoli/persone /
Face Detection and Recognition (max 15 faces per second) - Line Crossing, Area Intrusion, Anomaly, Vehicle/
People Count
Sorveglianza remota/remote control Browser IE, CVM per controllo da remoto - CVM for remote control
Utenti online/Online users 6 utenti / 6 users
Protocollo di rete/Network protocol UDP, IPv4, IPv6, DHCP, NTP, RTSP, PPPoE, DDNS, SMTP, FTP, HTTP, 802.1x, UPnP, HTTPs, QoS, TCP/IP
Compatibilità/Compatibility Onvif
Archiviazione/Storage Archiviazione su scheda SD - SD-card storage
Giorno e Notte/Day & Night Auto / Manual /Timing
Limite/Limit Pan Tilt 360° continuo, -5° a 90° auto Flip
Preset 360
Cruise/Track 8/4
Altro
Other
PoE Sì / Yes
Range IR Smart IR no a 150m / Smart IR up to 150m
Grado/Degree IP/IK IP66/-
Range temperatura/Temperature range -30° C +55°C
Alimentazione/Power supply 12 Vdc o PoE+(IEEE 802.3at)
Consumi/Consumptions Max 22 W
Dimensioni/Dimensions (mm) Ø173x247
Peso/Weight (g) 2100
Note multi-stream sta󰀨a inclusa / included bracket -
database max 10000 volti / database max 10000 faces
Ad esempio, l'indirizzo IP del computer in uso è 192.168.1.4. Di conseguenza l'indi-
rizzo della telecamera deve essere cambiato in 192.168.1.X.
Dopo la modica inserire la password di amministratore e fare clic sul pulsante
"Modica" per modicare l'impostazione.
La password predenita dell'amministratore è 123456.
4) Fare doppio clic sull'indirizzo IP, il sistema aprirà Internet Explorer per collega-
re l'IP-CAM. Internet Explorer scarica automaticamente i controlli ActiveX. Dopo il
download viene visualizzata la nestra di accesso. Immettere User Name (Nome
utente) e Password per accedere.
Il Nome Utente predenito è admin, la Password è 123456
6.2 Accesso alla telecamera tramite Internet Explorer
Le impostazioni di rete predenite sono indicate di seguito:
- Indirizzo IP: 192.168.226.201 HTTP:80
- Subnet Mask: 255.255.255.0 Porta Dati:9008
- Gateway: 192.168.226.1
Il Nome Utente predenito è admin, la Password è 123456
For example, the IP address of your computer is 192.168.1.4. So the IP address of
the camera shall be changed to 192.168.1.X.
After modication, please input the password of the administrator and click “Modify”
button to modify the setting.
The default password of the administrator is 123456.
4) Double-click the IP address and then the system will pop up the IE browser to connect
IP-CAM.
IE browser will automatically download the Active X control.
After downloading, a login window will pop up. Input the user name and password to login.
The default password of the administrator is 123456.
6.2 Directly Access Through IE
The default network settings are as shown below:
IP address: 192.168.226.201 HTTP:80
Subnet Mask: 255.255.255.0 Data Port:9008
Gateway: 192.168.226.1
The default user is admin, password of the administrator is 123456.

Viale Vicenza, 14
36063 Marostica VI - Italy
www.vimar.com
49401710A0 00 2105
46235.015B
Descrizione Preset / Preset Description
Chiama Preset/
Call Preset
Call No. 90 Preset Run track 1
Call No. 91 Preset Run cruise 1
Call No. 92 Preset Run cruise 2
Call No. 93 Preset Run cruise 3
Call No. 94 Preset Run cruise 4
Call No. 95 Preset Menu OSD / OSD menu
Call No. 97 Preset Abilita scansione casuale / Enable random scan
Call No. 99 Preset Abilita P-SCAN / Enable P-PSCAN
Impostare Preset
Set Preset
Set No. 91 Preset Impostare scansione casuale;
Set random scan;
Set No. 92 Preset Imposta limite sinistro di P-PSCAN / Set left border of P-PSCAN
Set No. 93 Preset Imposta limite destro di P-PSCAN / Set right border of P-PSCAN
Regole di installazione
L’installazione deve essere e󰀨ettuata da personale qualicato con l’osservanza delle disposizioni regolanti
l’installazione del materiale elettrico in vigore nel paese dove i prodotti sono installati.
Conformità normativa
Direttiva EMC. Direttiva RoHS
Norme EN 55032, EN 55035, EN 63000
Regolamento REACh (UE) n. 1907/2006 – art.33. Il prodotto potrebbe contenere tracce di piombo.
RAEE - Informazioni agli utilizzatori
Il simbolo del cassonetto barrato riportato sull’apparecchiatura o sulla sua confezione indica
che il prodotto alla fine della propria vita utile deve essere raccolto separatamente dagli altri
rifiuti. L’utente dovrà, pertanto, conferire l’apparecchiatura giunta a fine vita agli idonei centri
comunali di raccolta differenziata dei rifiuti elettrotecnici ed elettronici. In alternativa alla gestione
autonoma, è possibile consegnare gratuitamente l’apparecchiatura che si desidera smaltire al distributore,
al momento dell’acquisto di una nuova apparecchiatura di tipo equivalente. Presso i distributori di prodotti
elettronici con superficie di vendita di almeno 400 m
2
è inoltre possibile consegnare gratuitamente, senza
obbligo di acquisto, i prodotti elettronici da smaltire con dimensioni inferiori a 25 cm. L’adeguata raccolta
differenziata per l’avvio successivo dell’apparecchiatura dismessa al riciclaggio, al trattamento e allo smal-
timento ambientalmente compatibile contribuisce ad evitare possibili effetti negativi sull’ambiente e sulla
salute e favorisce il reimpiego e/o riciclo dei materiali di cui è composta l’apparecchiatura.
Installation rules
Installation should be carried out by qualified staff in compliance with the current regulations regarding the
installation of electrical equipment in the country where the products are installed.
Conformity to Standards
EMC Directive. RoHS Directive
Standards EN 55032, EN 55035, EN 63000
REACH (EU) Regulation no. 1907/2006 – Art.33. The product may contain traces of lead.
WEEE - User information
If the crossed-out bin symbol appears on the equipment or packaging, this means the product
must not be included with other general waste at the end of its working life. The user must take
the worn product to a sorted waste center, or return it to the retailer when purchasing a new one.
Products for disposal can be consigned free of charge (without any new purchase obligation)
to retailers with a sales area of at least 400 m
2
, if they measure less than 25 cm. An efficient sorted waste
collection for the environmentally friendly disposal of the used device, or its subsequent recycling, helps
avoid the potential negative effects on the environment and people’s health, and encourages the re-use
and/or recycling of the construction materials.
Cautions
- Before operation, we strongly advise users to read this manual and keep it properly for using later.
- Please use the specied power supply to connect.
- Avoid from in correct operation, shock vibration, heavy pressing which can cause damage to product.
- Do not use corrosive detergent to clean main body of the camera. If necessary, please use soft dry
cloth to wipe dirt; for hard contamination, use neutral detergent. Any cleanser for high grade furniture is
applicable.
- Avoid aiming the camera directly towards extremely bright objects, such as, sun, as this may damage
the image sensor.
- Please follow the instructions to install the camera. Do not reverse the camera, or the reversing image
will be received.
- Do not operate it incase temperature, humidity and power supply are beyond the limited stipulations.
- Keep away from heat sources such as radiators, heat registers, stove., etc.
- This is product instructions not quality warranty. We may reserve the rights of amending the typographical
errors, inconsistencies with the latest version, software upgrades and product improvements,
interpretation and modication. These changes will be published in the latest version without special
notication.
- When this product is in use, the relevant contents of Microsoft, Apple and Google will be involved in.
The pictures and screenshots in this manual are only used to explain the usage of our product. The
ownerships of trademarks, logos and other intellectual properties related to Microsoft, Apple and Google
belong to the above-mentioned companies.
Avvertenze
- Prima di utilizzare il prodotto si raccomanda vivamente di leggere il manuale e di conservarlo in un luogo
sicuro per consultazione futura.
- Utilizzare l'alimentazione specicata per il collegamento.
- Evitare di azionare il prodotto in modo improprio, sottoporlo a urti o vibrazioni, forti pressioni che
possono danneggiarlo.
- Non utilizzare detergenti corrosivi per pulire il corpo principale della telecamera. Se necessario,
utilizzare un panno morbido e asciutto per pulirla; in caso di sporco resistente utilizzare un detergente
neutro. È possibile utilizzare detergenti per mobili di qualità.
- Non puntare la telecamera direttamente verso oggetti estremamente luminosi, ad esempio il sole, in
quanto si potrebbe danneggiare il sensore d'immagine.
- Seguire le istruzioni per installare la telecamera. Non rovesciare la telecamera, altrimenti riceverà
un'immagine rovesciata.
- Non azionarla se temperatura, umidità e alimentazione non corrispondono ai limiti o valori specicati.
- Tenere lontano da fonti di calore quali radiatori, bocchette dell'aria calda, stufe e simili.
- Il presente documento contiene le istruzioni per l'uso del prodotto. Non è la garanzia di qualità. Ci
riserviamo il diritto di correggere errori di stampa, incongruenze con la versione più recente,
aggiornamenti del software e miglioramenti, interpretazione e modiche al prodotto. Tali cambiamenti
saranno pubblicati nella versione più recente senza previa notica.
- Quando il prodotto è in uso, sono applicabili i contenuti di Microsoft, Apple e Google. Le immagini e le
schermate di questo manuale hanno lo scopo di spiegare l'utilizzo del prodotto. La proprietà dei marchi
commerciali, dei logo e altre proprietà intellettuali relative a Microsoft, Apple e Google appartengono alle
suddette aziende.
Privacy
Privacy Policy
Privacy
Informativa Privacy
In conformità a quanto previsto dal Regolamento UE 2016/679 in materia di tutela dei dati personali,
Vimar S.p.A. garantisce che il trattamento dei dati mediante prodotti elettronici è e󰀨ettuato riducendo
al minimo l’utilizzazione di dati personali e di dati identicativi, limitando il trattamento ai casi in cui è
strettamente necessario per il conseguimento degli scopi per i quali sono raccolti. I dati dell’Interessato
saranno trattati in base a quanto previsto nella informativa privacy prodotti/applicazione consultabile dal
nostro sito www.vimar.com sezione legal (Privacy Policy Prodotti - Applicazioni - Vimar energia positiva).
Ricordiamo che, in base a quanto previsto dal Regolamento UE 2016/679 in materia di tutela dei dati
personali, è responsabilità dell’utilizzatore, in qualità di titolare del trattamento dei dati raccolti durante
l’utilizzo del prodotto, tutelare e adottare delle misure di sicurezza idonee ad evitare la perdita dei dati
personali memorizzati e registrati.
Nel caso in cui i prodotti riprendano spazi pubblici, non solo la proprietà privata, dovrà essere apposta,
in modo visibile, l’informativa di ‘area videosorvegliata’ prevista dalla normativa privacy e riportata nel sito
del Garante della Privacy.
Le immagini potranno essere memorizzate per un periodo di 24 ore no ad un massimo di 72 ore nei
casi previsti nel Provvedimento del Garante della Privacy in materia di videosorveglianza (8 aprile 2010).
Inoltre, l’utilizzatore dovrà garantire e vericare la titolarità e la custodia delle proprie password e dei relativi
codici di accesso alle risorse web. L’Interessato al momento della richiesta di intervento al Centro Assistenza
Vimar, per poter consentire le attività di assistenza, deve fornire la password di accesso al sistema. La
fornitura della stessa è considerata come consenso al trattamento. Ogni Interessato sarà responsabile e
dovrà modicare la password di accesso al proprio sistema a seguito di ogni intervento svolto da parte del
Centro Assistenza Vimar.’
As required by Regulation (EU) 2016/679 on the protection of personal data, Vimar S.p.A. guarantees that
the electronic processing of data minimises the use of personal and other identication information, which
is only processed to the extent strictly necessary in order to achieve the purposes for which it was collected.
The personal information of the Data Subject is processed in accordance with the product/application privacy
policy available on our website www.vimar.com in the legal section (Product - App Privacy Policy - Vimar
energia positiva).
Please remember that, pursuant to Regulation (EU) 2016/679 on the protection of personal data, the user is
the controller of processing for the data collected during use of the products and, as such, is responsible for
adopting suitable security measures that protect the personal data recorded and stored, and avoid its loss.
Should the products monitor public areas and not just private property, it will be necessary to display - in a
visible manner - the information about the ‘area under video surveillance’ envisaged in the privacy policy
and specied on the website of the Italian Data Protection Authority (Garante).
Images may be stored for 24 hours, and for up to 72 hours in the cases envisaged in the video surveillance
measures issued by the Italian Data Protection Authority on 8 April 2010.
In addition, the user must guarantee safe possession of and control over its passwords and the related access
codes to its web resources. The Data Subject must provide the password for access to its system when
requesting help from the Vimar Support Centre, so that the related support can be provided. Provision of the
password represents consent for processing. Each Data Subject is responsible for changing the password
for access to its system on completion of the work carried out by the Vimar Support Centre.’