Vingtor ACM-M-A-V2 User manual

www.vingtor.com
Zenitel Norway AS
P.O. Box 4498 Nydalen
NO-0403 OSLO
Norway
STENTOFON and VINGTOR products are developed and marketed by Zenitel Norway AS. The company’s Quality Assurance System is certified to meet the requirements in NS-EN ISO 9001:2002. Zenitel
Norway AS reserves the right to modify designs and alter specifications without prior notice, in pursuance of a policy of continuous improvement. © 2009 Zenitel Norway AS.
DOC NO
A100K10587 v.1.0 [e-mail]
Phone list
In use indication
Microphone mute
Pause (Not used)
Redial
R (or Flash)
Dial keys
Loudspeaking
Ringing signal Hi
/
Lo volume
Flash/R switch. Select R mode
Handset Hi/Lo volume
Telephone line, RJ11
Ext. Phone, RJ11
VINGTOR analogue telephone DT-800M
USER GUIDE
ACM Telephone System
ACM-M-A-V2
2009.05.27
A100K 10587 v.1.0

Basic Functions
The functions and codes are the same for all analogue telephones.
Some analogue telephones have special feature keys which are needed for some of the described functions.
Establish internal telephone call
Lift handset●
Dial number of desired phone●
Call is set up when remote phone handset is lifted–
Replace handset to end the conversation●
Establish external telephone call
Lift handset●
Dial trunk access code (default = 001) to get external dial tone●
Optional: Enter user and PIN code for call authorization for call–
billing. See programming list for actual code.
Dial external phone number●
Call is set up when handset on remote phone is lifted–
Replace handset to end the conversation●
Receive call in noisy area
For calls in noisy areas, the telephone line will be connected in
parallel to a signal unit.
Signal unit will provide visual or audio indication on incoming–
call
Lift handset to receive call●
Public address (PA) call
Lift handset●
Dial 84 for general PA call without zones●
Call is set up towards the PA system–
System plays a DING-DONG to the PA system–
After DING-DONG, speak into handset for PA announcement●
Replace handset to end the PA call●
Microphone mute
Only for telephones with MUTE button.
Press and hold the MUTE button to block own microphone during●
conversation
Release the MUTE button to re-open the microphone●
Re-dial
Only for telephones with REDIAL button.
Replace handset or push the handset switch●
Lift handset●
Press the REDIAL button to repeat last dialed number●
Redial can not be used for external calls
+
X
MUTE
REDIAL
+
PBX Functions
Inquiry call
Only for telephones with R button.
Press R+2 during conversation●
Dial number of desired phone●
Call is set up when handset on remote enquired phone is lifted–
Press R+2 to toggle between the phones●
The other conversation will be parked–
Replace handset to disconnect both phones●
Call transfer
Only for telephones with R button.
Press R+2 during conversation●
Dial number of desired phone●
Call is set up when handset on remote enquired phone is lifted–
Press R+3 to transfer the call●
Replace handset to withdraw from conversation●
The two other phones will remain in conversation–
Call forwarding
Lift handset and dial 71●
Dial remote phone number you want calls forwarded to●
Press the●¾button to confirm
Replace handset●
Own phone will ring for ca. 10 sec. when called,–
then forwarded if not answered
Dial 70 from your own phone to cancel Call forwarding●
Follow me
Lift handset on the phone you want calls to be transferred to●
Dial 72●
Dial your own phone number●
Replace handset●
Own phone will ring for ca. 10 sec. when called,–
then transferred to present phone if not answered
Dial 73 + own phone number to cancel Follow me●
Busy notify
If the called station is busy, dial 57 or press the●¾button to send
an attention tone (3 beeps) to the busy stations.
Call priority and busy override
Only a selected set of telephones will have option for
busy override.
If caller get busy tone, dial 58 or●¾¾ for busy override
The other call is disconnected and the priority call is set up–
R
R R
++
++
CALLER OWN REMOTE
R
R
++
+
CALLER OWN REMOTE
++
CALLER OWN REMOTE
C=
+
+
CALLER OWN
PRESENT
C=
OR
OR