Vintage view Case & Crate Series User manual

Case & Crate
Bin Short (CC-BIN) Installation Instructions
The Bin Short is the base unit for all Case & Crate bin congurations.
Video guides, spec sheets, and additional support are available at vintageview.com/caseandcrate
• (2) Bin Side Wall
• (4) Bin Shelves
• (4) Levelers
Parts List & Congurations
• (4) Couplers (for vertical extension)
• (24) 5mm x 25mm Bolts with Nuts
• (1) Wall Anchor Bracket with
Bin/Locker Short (Figure A)
All parts included in this box for Bin; Locker Doors
(CC-LOCKER) required for Locker conguration
Bin/Locker Tall (Figure B)
Additional Bin needed (CC-BIN); Locker Doors
(CC-LOCKER) required for Locker conguration
Bin/Locker Extended Units (Figure C)
Bin Extension kits (CC-BIN-EX) required for modu-
lar, horizontal growth. Locker Doors (CC-LOCKER)
required for Locker conguration and additional Bins
and Extension Kits required for tall congurations.
• (1) Toggle Bolt

Instructions
Step 1: Prep the Pieces
Begin by orienting the Bin Side Wall. The front features
the thicker 1”x1” steel supports and the top of each
unit features one drill hole on the inside of the slimmer
1”x0.5” beam.
Insert the supplied levelers on the bottom of each unit that
will be used as a base. Insert End Caps to the top of the
unit (skip this if it will the base unit of a Bin Tall congura-
tion).
Step 2: Connect the Shelves
Lay the rst Bin Side Wall on the ground on its narrow
edge (at a 90-degree angle from the oor). Starting from
the top end, connect the rst shelf using the supplied metal
bolts inserted into the pre-drilled holes. Ensure the tabs of
the shelf are facing down and the shelf is ush with the top
of the support. Repeat this step for the middle shelfs.
When installing the bottom shelf, ensure its tabs are
facing up (the opposite of the other three shelves).
Pro Tip: When threading the bolts to the shelves, place
the bolt head on the outside of the unit for added security.
Step 3: Attach the Second Side Wall
Align the top of the second Side Wall with the top shelf
and connect using the provided bolts. Repeat for all other
shelves.
Front
Front

Step 3b: Prep for Extension Unit
When installing Extension units, do not thread the nut
until attached the shelf from the Extension kit. See the
“Make it Wide” instructions on next page for more
information.
Step 4: Finish
Stand the unit upright and add your favorite 16 bottles into each bin.
For maximum stability, we recommend attaching all Bin congurations to the wall using the included Wall
Anchor Bracket. With unit pressed against the wall, nd the pre-drilled hole on the back post of the Bin
unit and mark its location on the wall. Pre-drill a hole (1/2” for provided drywall anchor). Then, attach
the unit to the wall using the provided toggle bolt. Repeat for all Bin units.
Instructions

Make it Wide: Add extension units
The Case & Crate Bins and Lockers are designed to modularly extend left or right, sharing the inside
Support Wall.
1. Stand the Bin/Locker Short or Tall upright.
2. Starting from the top, install all shelves in the same manner as Step 2
3. Attach the Side wall on the outside in the same manner as Sept 3a
4. Repeat for as many Extension units necessary.
Reference Figure C
Accessorize
Make it a Locker
Installation instructions are included in all Locker Door (CC-LOCKER) packages. If you don’t have the
Locker Doors already, nd them at vintageview.com/caseandcrate.
Add an X-Bin
Installation instructions are included in all X-Bin (CC-XRACK) packages. If you don’t have an X-Bin al-
ready, nd them at caseandcrate.com.
Enhance your Bin
Make it Tall: Add a top unit
Build the top unit following Steps 1-3, removing the End
Caps from the base. Conrm that the base Bin unit has
the supplied Levelers attached to the bottom and the
End Caps removed from the top.
With the base Bin unit standing upright, insert supplied
Couplers to the top of the unit. Slide the top Bin onto its
respective set of Couplers.
For installations including Extension Kits, install the rst top
Bin with the shelf nuts not secured (Step 3b), then connect
the extension shelves, followed by the Extension Kit Side
Wall. Repeat as many times as necessary.