Vintage view VR Series User manual

Vino Rails for Wood Surfaces
Installation instructions for Vino Rails (SKUs: VR-)
Included Parts
• (2) Vino Rails
• (2) Wood Lags
• (1) Hex Key
• (2) Nuts
• (1) 8.5”x11” Plotting Guide
Required Tools
• (1) Level
• (1) Drill
• (1) 5/32” (4mm) Drill Bit
• (2) 10mm or adjustable
wrenches, or...
• (1) M6 Driver (recommended)
Important Note: The following instructions are for installing Vino Rails for Wood Surfaces (standard wine
bottles, 750ml). Installation surfaces must have a minimum thickness of 1/2” (13.7mm). Please reference the
BILT 3D app and/or product specic guides for drywall-backed or Magnum bottle (1.5L) instructions.
Figure B
1. MARK MOUNTING HOLE LOCATIONS
Use a level to ensure the printed mounting template is
horizontal along the long edge (Figure A), mark hole
locations by piercing the template with a pencil or sharp
at the center the two (2) marks corresponding with the
bottle direction chosen. Mounting holes will be 2-1/2”
(65mm) apart.
For Magnum racking, adjust to 3” (77mm) but reference
product specic instructions.
Pro Tip: To plot additional Vino Rails in the same column,
mark a minimum of 5” (127mm) above or below each
mounting hole for next set of Vino Rails.
2. CONFIRM WALL SURFACE
Drill two (2) pilot holes using a 5/32” (4mm) Drill Bit
(Figure B) to determine whether your installation will
be into solid wood or drywall surface.
NOTE: If it is determined to be drywall, please use
(or purchase if necessary) Vino Series Collars and
reference the Vino Rails with Collars (SKUs: VRC-)
install guide.
Figure A

Instructions: Vino Rails for Wood Surfaces (VR)
Figure F
3. INSTALL WOOD LAGS
a. Using Hex Key or M6 Driver
Using either the provided hex key, drive the Lag Stud
into the pilot holes until the coarse threads are no longer
visible. When driving the Lag Stud, take care to ensure it
remains level.
For larger projects or if a sturdier tool is needed, use an
optional M6 Driver.
b. Using Nuts
Alternatively, attach two (2) provided nuts onto the ne
threaded end of the Lag Stud. Using two 10mm wrench-
es, tighten the nuts against one another (Figure C), essen-
tially creating a screw head. Then use one wrench on the
outer nut and screw the wood lag into the pilot holes until
the coarse threads are no longer visible.
4. INSTALL VINO RAILS
Thread two (2) Vino Rails onto the Studs (Figure D). Then,
rmly hand-tighten taking care not to over tighten. Con-
rm Rails are level.
5. ADD WINE
Only the good stuff.
Problems?
Try Vino Rails installation using BILT 3D intelligent instruc-
tions, visit www.vintageview.com or give us a call at
303-504-9463.
Additional Notes:
All installations into drywall require the use of collars and
alternate fasteners to properly support the Vino Rails. Any
application outside of these parameters is not warranted
by VintageView and may result in product and/or instal-
Figure C
Figure C Figure D
lation failure, property dam-
age and/or bodily injury.
Care:
Vino Rails should be regu-
larly checked for tightness.
Should any rack to be found
to be loose, tighten by hand
until secure. If the face of the
wall surface shows signs of breakage, discontinue
use immediately until the wall may be adequately
repaired.
Vino Rails may be cleaned a dry dusting cloth, com-
pressed air cans, rubbing alcohol and a clean cloth
to remove grease, oil, or other substances. Do not
use cleaning supplies or abrasive surfaces as they
will damage the nished surfaces of the parts.