Virgin Pure T6 WaterBar Operating manual

Changing your
purication supplies
T6 WaterBar

Better water, pure and simple
We hope you’re enjoying your unlimited supply of pure water.
To ensure that your WaterBar keeps giving you pure water, now is the time to replace some
supplies. After this (as now) your WaterBar will continue to serve a little bit of water heaven
with every button pressed!
You will either receive box 1 or box 2 depending on which supplies need to be changed:
Box 1
A descaling pod
A replacement lter – to keep the water pure and clean
Box 2
A descaling pod
A replacement lter – to keep the water pure and clean
A new UV lamp – to kill bacteria and viruses
By replacing it’s worn out supplies with shiny new models you’ll keep your Virgin Pure WaterBar
working beautifully. So you can keep drinking tasty, clean pure water to your
heart’s content.
It’s quick and simple to give your WaterBar some well deserved TLC. Follow this step by step
guide and you’ll be up and running in no time. If you get stuck:
• Try the trouble shooting guide on page 7
• Visit the Help & Support pages on www.virginpure.com
• Give us a call on 0845 301 7700
We’re always here to help.
If you’re not 100% happy email us at [e-mail]
and we’ll get it xed for you – whatever it is. It’s that simple.
Keep it pure, Virgin Pure.
2

Every 6 months - the de-scaling process
and inserting a new lter
The descaling pod contains citric salt for scale removal. When descaling your WaterBar it can’t
be used for approximately six hours, it’s therefore best performed overnight. Your WaterBar
needs to be de-scaled before you change your lter.
Leave your WaterBar switched
on. Remove the lid.
Insert the pod into the lter’s
position (either way round)
until it clicks rmly into place.
Do not drink water from the
WaterBar from this point
until the process is complete.
After at least six hours, press the
EXTRA HOT button, and then wait
until the water boils. Dispense four
litres of water by pressing the HOT
button. Air may still be present in
the system so a light spluttering
may occur. If there are scale
particles still in the water,
repeat this step.
Press PUSH and pull the lter
up using the ribbon tab.
Dispose of the lter in
accordance with your Local
Authority guidelines.
Press the HOT button and let
the hot water run for 1 minute.
Place a ve-litre container
under the spout.
Remove the pod from its
package. Wet the stems
(legs) of the pod with water
to lubricate before inserting.
Press the EXTRA HOT
button, and wait for the
water to boil.
Stick the warning label
enclosed with this pack on the
front of the device to ensure no
one uses it whilst the descaler
is working, and wait for at
least six hours.
3
How to perform the descaling process
Needs to be performed every six months
Note : the unit cannot be used during the scale removal process for approximately
6 hours.
Therefore it is recommended to carry out the procedure at night
* The capsule contains citric salt for scale removal.
1. Remove the rubber pad. 2. Press the PUSH button and pull the filter
upwards, using the ribbon tab.
3. Remove the cleaning capsule from its
package.
4. Insert the capsule to the filter's position
(in any direction), until it snaps firmly into
place.
Attention
:
As of now and until the
process completes, do not drink
water from the device.
5. Place a 5 liter container under the spout. 6. Press the EH (EXTRA HOT) button, and wait
for the water to boil.
3
How to perform the descaling process
Needs to be performed every six months
Note : the unit cannot be used during the scale removal process for approximately
6 hours.
Therefore it is recommended to carry out the procedure at night
* The capsule contains citric salt for scale removal.
1. Remove the rubber pad. 2. Press the PUSH button and pull the filter
upwards, using the ribbon tab.
3. Remove the cleaning capsule from its
package.
4. Insert the capsule to the filter's position
(in any direction), until it snaps firmly into
place.
Attention
:
As of now and until the
process completes, do not drink
water from the device.
5. Place a 5 liter container under the spout. 6. Press the EH (EXTRA HOT) button, and wait
for the water to boil.
3
How to perform the descaling process
Needs to be performed every six months
Note : the unit cannot be used during the scale removal process for approximately
6 hours.
Therefore it is recommended to carry out the procedure at night
* The capsule contains citric salt for scale removal.
1. Remove the rubber pad. 2. Press the PUSH button and pull the filter
upwards, using the ribbon tab.
3. Remove the cleaning capsule from its
package.
4. Insert the capsule to the filter's position
(in any direction), until it snaps firmly into
place.
Attention
:
As of now and until the
process completes, do not drink
water from the device.
5. Place a 5 liter container under the spout. 6. Press the EH (EXTRA HOT) button, and wait
for the water to boil.
3
How to perform the descaling process
Needs to be performed every six months
Note : the unit cannot be used during the scale removal process for approximately
6 hours.
Therefore it is recommended to carry out the procedure at night
* The capsule contains citric salt for scale removal.
1. Remove the rubber pad. 2. Press the PUSH button and pull the filter
upwards, using the ribbon tab.
3. Remove the cleaning capsule from its
package.
4. Insert the capsule to the filter's position
(in any direction), until it snaps firmly into
place.
Attention: As of now and until the
process completes, do not drink
water from the device.
5. Place a 5 liter container under the spout. 6. Press the EH (EXTRA HOT) button, and wait
for the water to boil.
3
How to perform the descaling process
Needs to be performed every six months
Note : the unit cannot be used during the scale removal process for approximately
6 hours.
Therefore it is recommended to carry out the procedure at night
* The capsule contains citric salt for scale removal.
1. Remove the rubber pad. 2. Press the PUSH button and pull the filter
upwards, using the ribbon tab.
3. Remove the cleaning capsule from its
package.
4. Insert the capsule to the filter's position
(in any direction), until it snaps firmly into
place.
Attention : As of now and until the
process completes, do not drink
water from the device.
5. Place a 5 liter container under the spout. 6. Press the EH (EXTRA HOT) button, and wait
for the water to boil.
3
How to perform the descaling process
Needs to be performed every six months
Note : the unit cannot be used during the scale removal process for approximately
6 hours.
Therefore it is recommended to carry out the procedure at night
* The capsule contains citric salt for scale removal.
1. Remove the rubber pad. 2. Press the PUSH button and pull the filter
upwards, using the ribbon tab.
3. Remove the cleaning capsule from its
package.
4. Insert the capsule to the filter's position
(in any direction), until it snaps firmly into
place.
Attention: As of now and until the
process completes, do not drink
water from the device.
5. Place a 5 liter container under the spout. 6. Press the EH (EXTRA HOT) button, and wait
for the water to boil.
3
How to perform the descaling process
Needs to be performed every six months
Note : the unit cannot be used during the scale removal process for approximately
6 hours.
Therefore it is recommended to carry out the procedure at night
* The capsule contains citric salt for scale removal.
1. Remove the rubber pad. 2. Press the PUSH button and pull the filter
upwards, using the ribbon tab.
3. Remove the cleaning capsule from its
package.
4. Insert the capsule to the filter's position
(in any direction), until it snaps firmly into
place.
Attention: As of now and until the
process completes, do not drink
water from the device.
5. Place a 5 liter container under the spout. 6. Press the EH (EXTRA HOT) button, and wait
for the water to boil.
4
7. Press the Hot Water button (HOT) and let
hot water run for 1 minute.
8. Place the included warning label on the
front of the device and wait for at
least 6 hours.
Attention!
Appliance is in descaling process
Do not use
Remove sticker when process ends &
follow attached instruction
9. After the wait, press the PUSH button,
remove the capsule, and discard it.
10.Place a 5 liter container under the spout.
Push the filter back to its position, until it
snaps firmly into place.
11.Press the EH (EXTRA HOT) button, and wait
for the water to boil.
Attention!
Appliance is in descaling process
Do not use
Remove sticker when process ends &
follow attached instruction
12.Press the Hot Water button (HOT) and let
hot water run for 3 minutes.
Note: If there are still scale particles in the
water, repeat Step 12.
13.The scale removal process is completed.
Remove the warning label and discard it.
The device is ready for use.
Note: For more information, please contact
Customer Service.
4
7. Press the Hot Water button (HOT) and let
hot water run for 1 minute.
8. Place the included warning label on the
front of the device and wait for at
least 6 hours.
Attention!
Appliance is in descaling process
Do not use
Remove sticker when process ends &
follow attached instruction
9. After the wait, press the PUSH button,
remove the capsule, and discard it.
10.Place a 5 liter container under the spout.
Push the filter back to its position, until it
snaps firmly into place.
11.Press the EH (EXTRA HOT) button, and wait
for the water to boil.
Attention!
Appliance is in descaling process
Do not use
Remove sticker when process ends &
follow attached instruction
12.Press the Hot Water button (HOT) and let
hot water run for 3 minutes.
Note: If there are still scale particles in the
water, repeat Step 12.
13.The scale removal process is completed.
Remove the warning label and discard it.
The device is ready for use.
Note: For more information, please contact
Customer Service.
1
4
7
2
5
8
3
6
9
3

4
7. Press the Hot Water button (HOT) and let
hot water run for 1 minute.
8. Place the included warning label on the
front of the device and wait for at
least 6 hours.
Attention!
Appliance is in descaling process
Do not use
Remove sticker when process ends &
follow attached instruction
9. After the wait, press the PUSH button,
remove the capsule, and discard it.
10.Place a 5 liter container under the spout.
Push the filter back to its position, until it
snaps firmly into place.
11.Press the EH (EXTRA HOT) button, and wait
for the water to boil.
Attention!
Appliance is in descaling process
Do not use
Remove sticker when process ends &
follow attached instruction
12.Press the Hot Water button (HOT) and let
hot water run for 3 minutes.
Note: If there are still scale particles in the
water, repeat Step 12.
13.The scale removal process is completed.
Remove the warning label and discard it.
The device is ready for use.
Note: For more information, please contact
Customer Service.
2
“REPLACEMENT”Press
Press Press
Press
Press
What does the kit include?
A filter with an extraction tab
How to change the filter
a. Removing the Used Filter and Installing a New Filter with Extraction Tab
1. Remove the rubber pad 2. Press the PUSH button and
pull the filter out
3. Remove the new filter from its
wrapper (make sure that the
extraction tab is attached)
4. Insert the filter until you hear
a click
5. Replace the rubber pad
b. Draining the Air bubble from the New Filter
1. Press the cold water button
(COLD) for 2 minutes
2. Wait for 10 minutes 3. Press the cold waterbutton
again, until water starts running
c. Resetting the Filter’s Counter
1. Click MENU 2. *Scroll to “Change filter/lamp" 3. Click OK
4. *Scroll to “Filter” 5. Click OK 6. *Scroll to “Yes”
7. Click OK 8. Click BACK until the main
screen appears
What does the kit include?
A filter with an extraction tab
How to change the filter
a. Removing the Used Filter and Installing a New Filter with Extraction Tab
1. Remove the rubber pad 2. Press the PUSH button and
pull the filter out
3. Remove the new filter from its
wrapper (make sure that the
extraction tab is attached)
4. Insert the filter until you hear
a click
5. Replace the rubber pad
b. Draining the Air bubble from the New Filter
1. Press the cold water button
(COLD) for 2 minutes
2. Wait for 10 minutes 3. Press the cold waterbutton
again, until water starts running
c. Resetting the Filter’s Counter
1. Click MENU 2. *Scroll to “Change filter/lamp" 3. Click OK
4. *Scroll to “Filter” 5. Click OK 6. *Scroll to “Yes”
7. Click OK 8. Click BACK until the main
screen appears
1. Place Jug under spout
2. 3. 4.
Press the PUSH button,
pull the filter out using the
extraction tab and
discard it
Filter change every 6 months
* In T6 2 button models, scrolling is done using the COLD button only.
2
“REPLACEMENT”Press
Press Press
Press
Press
What does the kit include?
A filter with an extraction tab
How to change the filter
a. Removing the Used Filter and Installing a New Filter with Extraction Tab
1. Remove the rubber pad 2. Press the PUSH button and
pull the filter out
3. Remove the new filter from its
wrapper (make sure that the
extraction tab is attached)
4. Insert the filter until you hear
a click
5. Replace the rubber pad
b. Draining the Air bubble from the New Filter
1. Press the cold water button
(COLD) for 2 minutes
2. Wait for 10 minutes 3. Press the cold waterbutton
again, until water starts running
c. Resetting the Filter’s Counter
1. Click MENU 2. *Scroll to “Change filter/lamp" 3. Click OK
4. *Scroll to “Filter” 5. Click OK 6. *Scroll to “Yes”
7. Click OK 8. Click BACK until the main
screen appears
What does the kit include?
A filter with an extraction tab
How to change the filter
a. Removing the Used Filter and Installing a New Filter with Extraction Tab
1. Remove the rubber pad 2. Press the PUSH button and
pull the filter out
3. Remove the new filter from its
wrapper (make sure that the
extraction tab is attached)
4. Insert the filter until you hear
a click
5. Replace the rubber pad
b. Draining the Air bubble from the New Filter
1. Press the cold water button
(COLD) for 2 minutes
2. Wait for 10 minutes 3. Press the cold waterbutton
again, until water starts running
c. Resetting the Filter’s Counter
1. Click MENU 2. *Scroll to “Change filter/lamp" 3. Click OK
4. *Scroll to “Filter” 5. Click OK 6. *Scroll to “Yes”
7. Click OK 8. Click BACK until the main
screen appears
1. Place Jug under spout
2. 3. 4.
Press the PUSH button,
pull the filter out using the
extraction tab and
discard it
Filter change every 6 months
* In T6 2 button models, scrolling is done using the COLD button only.
2
“REPLACEMENT”Press
Press Press
Press
Press
What does the kit include?
A filter with an extraction tab
How to change the filter
a. Removing the Used Filter and Installing a New Filter with Extraction Tab
1. Remove the rubber pad 2. Press the PUSH button and
pull the filter out
3. Remove the new filter from its
wrapper (make sure that the
extraction tab is attached)
4. Insert the filter until you hear
a click
5. Replace the rubber pad
b. Draining the Air bubble from the New Filter
1. Press the cold water button
(COLD) for 2 minutes
2. Wait for 10 minutes 3. Press the cold waterbutton
again, until water starts running
c. Resetting the Filter’s Counter
1. Click MENU 2. *Scroll to “Change filter/lamp" 3. Click OK
4. *Scroll to “Filter” 5. Click OK 6. *Scroll to “Yes”
7. Click OK 8. Click BACK until the main
screen appears
What does the kit include?
A filter with an extraction tab
How to change the filter
a. Removing the Used Filter and Installing a New Filter with Extraction Tab
1. Remove the rubber pad 2. Press the PUSH button and
pull the filter out
3. Remove the new filter from its
wrapper (make sure that the
extraction tab is attached)
4. Insert the filter until you hear
a click
5. Replace the rubber pad
b. Draining the Air bubble from the New Filter
1. Press the cold water button
(COLD) for 2 minutes
2. Wait for 10 minutes 3. Press the cold waterbutton
again, until water starts running
c. Resetting the Filter’s Counter
1. Click MENU 2. *Scroll to “Change filter/lamp" 3. Click OK
4. *Scroll to “Filter” 5. Click OK 6. *Scroll to “Yes”
7. Click OK 8. Click BACK until the main
screen appears
1. Place Jug under spout
2. 3. 4.
Press the PUSH button,
pull the filter out using the
extraction tab and
discard it
Filter change every 6 months
* In T6 2 button models, scrolling is done using the COLD button only.
10
13
11 12
2
“REPLACEMENT”Press
Press Press
Press
Press
What does the kit include?
A filter with an extraction tab
How to change the filter
a. Removing the Used Filter and Installing a New Filter with Extraction Tab
1. Remove the rubber pad 2. Press the PUSH button and
pull the filter out
3. Remove the new filter from its
wrapper (make sure that the
extraction tab is attached)
4. Insert the filter until you hear
a click
5. Replace the rubber pad
b. Draining the Air bubble from the New Filter
1. Press the cold water button
(COLD) for 2 minutes
2. Wait for 10 minutes 3. Press the cold waterbutton
again, until water starts running
c. Resetting the Filter’s Counter
1. Click MENU 2. *Scroll to “Change filter/lamp" 3. Click OK
4. *Scroll to “Filter” 5. Click OK 6. *Scroll to “Yes”
7. Click OK 8. Click BACK until the main
screen appears
What does the kit include?
A filter with an extraction tab
How to change the filter
a. Removing the Used Filter and Installing a New Filter with Extraction Tab
1. Remove the rubber pad 2. Press the PUSH button and
pull the filter out
3. Remove the new filter from its
wrapper (make sure that the
extraction tab is attached)
4. Insert the filter until you hear
a click
5. Replace the rubber pad
b. Draining the Air bubble from the New Filter
1. Press the cold water button
(COLD) for 2 minutes
2. Wait for 10 minutes 3. Press the cold waterbutton
again, until water starts running
c. Resetting the Filter’s Counter
1. Click MENU 2. *Scroll to “Change filter/lamp" 3. Click OK
4. *Scroll to “Filter” 5. Click OK 6. *Scroll to “Yes”
7. Click OK 8. Click BACK until the main
screen appears
1. Place Jug under spout
2. 3. 4.
Press the PUSH button,
pull the filter out using the
extraction tab and
discard it
Filter change every 6 months
* In T6 2 button models, scrolling is done using the COLD button only.
Insert the lter until you
hear a click.
Replace the lid and remove the
warning label.
To remove the descaling pod,
press PUSH, remove the pod,
and dispose of it in accordance
with your Local Authority
guidelines.
The de-scaling process is now
complete.
Unwrap your new lter,
making sure the ribbon tab
stays in place.
Place a jug under the spout and
press the COLD button for two
minutes.
Draining the air from your new lter
Place a container under the
spout and press the COLD
button for two minutes.
Wait for 10 minutes.
14 15
2
“REPLACEMENT”Press
Press Press
Press
Press
What does the kit include?
A filter with an extraction tab
How to change the filter
a. Removing the Used Filter and Installing a New Filter with Extraction Tab
1. Remove the rubber pad 2. Press the PUSH button and
pull the filter out
3. Remove the new filter from its
wrapper (make sure that the
extraction tab is attached)
4. Insert the filter until you hear
a click
5. Replace the rubber pad
b. Draining the Air bubble from the New Filter
1. Press the cold water button
(COLD) for 2 minutes
2. Wait for 10 minutes 3. Press the cold waterbutton
again, until water starts running
c. Resetting the Filter’s Counter
1. Click MENU 2. *Scroll to “Change filter/lamp" 3. Click OK
4. *Scroll to “Filter” 5. Click OK 6. *Scroll to “Yes”
7. Click OK 8. Click BACK until the main
screen appears
What does the kit include?
A filter with an extraction tab
How to change the filter
a. Removing the Used Filter and Installing a New Filter with Extraction Tab
1. Remove the rubber pad 2. Press the PUSH button and
pull the filter out
3. Remove the new filter from its
wrapper (make sure that the
extraction tab is attached)
4. Insert the filter until you hear
a click
5. Replace the rubber pad
b. Draining the Air bubble from the New Filter
1. Press the cold water button
(COLD) for 2 minutes
2. Wait for 10 minutes 3. Press the cold waterbutton
again, until water starts running
c. Resetting the Filter’s Counter
1. Click MENU 2. *Scroll to “Change filter/lamp" 3. Click OK
4. *Scroll to “Filter” 5. Click OK 6. *Scroll to “Yes”
7. Click OK 8. Click BACK until the main
screen appears
1. Place Jug under spout
2. 3. 4.
Press the PUSH button,
pull the filter out using the
extraction tab and
discard it
Filter change every 6 months
* In T6 2 button models, scrolling is done using the COLD button only.
16
4

To reset your lter counter
Immediately after replacing the lter you need to reset the counter so that your WaterBar will
tell you when your lter needs changing again.
Press MENU.
Scroll to FILTER.
Press OK.
Scroll to REPLACEMENT.
Press OK.
Press BACK until the main
screen appears.
Press OK.
Scroll to Yes.
2
“REPLACEMENT”Press
Press Press
Press
Press
What does the kit include?
A filter with an extraction tab
How to change the filter
a. Removing the Used Filter and Installing a New Filter with Extraction Tab
1. Remove the rubber pad 2. Press the PUSH button and
pull the filter out
3. Remove the new filter from its
wrapper (make sure that the
extraction tab is attached)
4. Insert the filter until you hear
a click
5. Replace the rubber pad
b. Draining the Air bubble from the New Filter
1. Press the cold water button
(COLD) for 2 minutes
2. Wait for 10 minutes 3. Press the cold waterbutton
again, until water starts running
c. Resetting the Filter’s Counter
1. Click MENU 2. *Scroll to “Change filter/lamp" 3. Click OK
4. *Scroll to “Filter” 5. Click OK 6. *Scroll to “Yes”
7. Click OK 8. Click BACK until the main
screen appears
What does the kit include?
A filter with an extraction tab
How to change the filter
a. Removing the Used Filter and Installing a New Filter with Extraction Tab
1. Remove the rubber pad 2. Press the PUSH button and
pull the filter out
3. Remove the new filter from its
wrapper (make sure that the
extraction tab is attached)
4. Insert the filter until you hear
a click
5. Replace the rubber pad
b. Draining the Air bubble from the New Filter
1. Press the cold water button
(COLD) for 2 minutes
2. Wait for 10 minutes 3. Press the cold waterbutton
again, until water starts running
c. Resetting the Filter’s Counter
1. Click MENU 2. *Scroll to “Change filter/lamp" 3. Click OK
4. *Scroll to “Filter” 5. Click OK 6. *Scroll to “Yes”
7. Click OK 8. Click BACK until the main
screen appears
1. Place Jug under spout
2. 3. 4.
Press the PUSH button,
pull the filter out using the
extraction tab and
discard it
Filter change every 6 months
* In T6 2 button models, scrolling is done using the COLD button only.
2
“REPLACEMENT”Press
Press Press
Press
Press
What does the kit include?
A filter with an extraction tab
How to change the filter
a. Removing the Used Filter and Installing a New Filter with Extraction Tab
1. Remove the rubber pad 2. Press the PUSH button and
pull the filter out
3. Remove the new filter from its
wrapper (make sure that the
extraction tab is attached)
4. Insert the filter until you hear
a click
5. Replace the rubber pad
b. Draining the Air bubble from the New Filter
1. Press the cold water button
(COLD) for 2 minutes
2. Wait for 10 minutes 3. Press the cold waterbutton
again, until water starts running
c. Resetting the Filter’s Counter
1. Click MENU 2. *Scroll to “Change filter/lamp" 3. Click OK
4. *Scroll to “Filter” 5. Click OK 6. *Scroll to “Yes”
7. Click OK 8. Click BACK until the main
screen appears
What does the kit include?
A filter with an extraction tab
How to change the filter
a. Removing the Used Filter and Installing a New Filter with Extraction Tab
1. Remove the rubber pad 2. Press the PUSH button and
pull the filter out
3. Remove the new filter from its
wrapper (make sure that the
extraction tab is attached)
4. Insert the filter until you hear
a click
5. Replace the rubber pad
b. Draining the Air bubble from the New Filter
1. Press the cold water button
(COLD) for 2 minutes
2. Wait for 10 minutes 3. Press the cold waterbutton
again, until water starts running
c. Resetting the Filter’s Counter
1. Click MENU 2. *Scroll to “Change filter/lamp" 3. Click OK
4. *Scroll to “Filter” 5. Click OK 6. *Scroll to “Yes”
7. Click OK 8. Click BACK until the main
screen appears
1. Place Jug under spout
2. 3. 4.
Press the PUSH button,
pull the filter out using the
extraction tab and
discard it
Filter change every 6 months
* In T6 2 button models, scrolling is done using the COLD button only.
2
“REPLACEMENT”Press
Press Press
Press
Press
What does the kit include?
A filter with an extraction tab
How to change the filter
a. Removing the Used Filter and Installing a New Filter with Extraction Tab
1. Remove the rubber pad 2. Press the PUSH button and
pull the filter out
3. Remove the new filter from its
wrapper (make sure that the
extraction tab is attached)
4. Insert the filter until you hear
a click
5. Replace the rubber pad
b. Draining the Air bubble from the New Filter
1. Press the cold water button
(COLD) for 2 minutes
2. Wait for 10 minutes 3. Press the cold waterbutton
again, until water starts running
c. Resetting the Filter’s Counter
1. Click MENU 2. *Scroll to “Change filter/lamp" 3. Click OK
4. *Scroll to “Filter” 5. Click OK 6. *Scroll to “Yes”
7. Click OK 8. Click BACK until the main
screen appears
What does the kit include?
A filter with an extraction tab
How to change the filter
a. Removing the Used Filter and Installing a New Filter with Extraction Tab
1. Remove the rubber pad 2. Press the PUSH button and
pull the filter out
3. Remove the new filter from its
wrapper (make sure that the
extraction tab is attached)
4. Insert the filter until you hear
a click
5. Replace the rubber pad
b. Draining the Air bubble from the New Filter
1. Press the cold water button
(COLD) for 2 minutes
2. Wait for 10 minutes 3. Press the cold waterbutton
again, until water starts running
c. Resetting the Filter’s Counter
1. Click MENU 2. *Scroll to “Change filter/lamp" 3. Click OK
4. *Scroll to “Filter” 5. Click OK 6. *Scroll to “Yes”
7. Click OK 8. Click BACK until the main
screen appears
1. Place Jug under spout
2. 3. 4.
Press the PUSH button,
pull the filter out using the
extraction tab and
discard it
Filter change every 6 months
* In T6 2 button models, scrolling is done using the COLD button only.
2
“REPLACEMENT”Press
Press Press
Press
Press
What does the kit include?
A filter with an extraction tab
How to change the filter
a. Removing the Used Filter and Installing a New Filter with Extraction Tab
1. Remove the rubber pad 2. Press the PUSH button and
pull the filter out
3. Remove the new filter from its
wrapper (make sure that the
extraction tab is attached)
4. Insert the filter until you hear
a click
5. Replace the rubber pad
b. Draining the Air bubble from the New Filter
1. Press the cold water button
(COLD) for 2 minutes
2. Wait for 10 minutes 3. Press the cold waterbutton
again, until water starts running
c. Resetting the Filter’s Counter
1. Click MENU 2. *Scroll to “Change filter/lamp" 3. Click OK
4. *Scroll to “Filter” 5. Click OK 6. *Scroll to “Yes”
7. Click OK 8. Click BACK until the main
screen appears
What does the kit include?
A filter with an extraction tab
How to change the filter
a. Removing the Used Filter and Installing a New Filter with Extraction Tab
1. Remove the rubber pad 2. Press the PUSH button and
pull the filter out
3. Remove the new filter from its
wrapper (make sure that the
extraction tab is attached)
4. Insert the filter until you hear
a click
5. Replace the rubber pad
b. Draining the Air bubble from the New Filter
1. Press the cold water button
(COLD) for 2 minutes
2. Wait for 10 minutes 3. Press the cold waterbutton
again, until water starts running
c. Resetting the Filter’s Counter
1. Click MENU 2. *Scroll to “Change filter/lamp" 3. Click OK
4. *Scroll to “Filter” 5. Click OK 6. *Scroll to “Yes”
7. Click OK 8. Click BACK until the main
screen appears
1. Place Jug under spout
2. 3. 4.
Press the PUSH button,
pull the filter out using the
extraction tab and
discard it
Filter change every 6 months
* In T6 2 button models, scrolling is done using the COLD button only.
2
“REPLACEMENT”Press
Press Press
Press
Press
What does the kit include?
A filter with an extraction tab
How to change the filter
a. Removing the Used Filter and Installing a New Filter with Extraction Tab
1. Remove the rubber pad 2. Press the PUSH button and
pull the filter out
3. Remove the new filter from its
wrapper (make sure that the
extraction tab is attached)
4. Insert the filter until you hear
a click
5. Replace the rubber pad
b. Draining the Air bubble from the New Filter
1. Press the cold water button
(COLD) for 2 minutes
2. Wait for 10 minutes 3. Press the cold waterbutton
again, until water starts running
c. Resetting the Filter’s Counter
1. Click MENU 2. *Scroll to “Change filter/lamp" 3. Click OK
4. *Scroll to “Filter” 5. Click OK 6. *Scroll to “Yes”
7. Click OK 8. Click BACK until the main
screen appears
What does the kit include?
A filter with an extraction tab
How to change the filter
a. Removing the Used Filter and Installing a New Filter with Extraction Tab
1. Remove the rubber pad 2. Press the PUSH button and
pull the filter out
3. Remove the new filter from its
wrapper (make sure that the
extraction tab is attached)
4. Insert the filter until you hear
a click
5. Replace the rubber pad
b. Draining the Air bubble from the New Filter
1. Press the cold water button
(COLD) for 2 minutes
2. Wait for 10 minutes 3. Press the cold waterbutton
again, until water starts running
c. Resetting the Filter’s Counter
1. Click MENU 2. *Scroll to “Change filter/lamp" 3. Click OK
4. *Scroll to “Filter” 5. Click OK 6. *Scroll to “Yes”
7. Click OK 8. Click BACK until the main
screen appears
1. Place Jug under spout
2. 3. 4.
Press the PUSH button,
pull the filter out using the
extraction tab and
discard it
Filter change every 6 months
* In T6 2 button models, scrolling is done using the COLD button only.
2
“REPLACEMENT”Press
Press Press
Press
Press
What does the kit include?
A filter with an extraction tab
How to change the filter
a. Removing the Used Filter and Installing a New Filter with Extraction Tab
1. Remove the rubber pad 2. Press the PUSH button and
pull the filter out
3. Remove the new filter from its
wrapper (make sure that the
extraction tab is attached)
4. Insert the filter until you hear
a click
5. Replace the rubber pad
b. Draining the Air bubble from the New Filter
1. Press the cold water button
(COLD) for 2 minutes
2. Wait for 10 minutes 3. Press the cold waterbutton
again, until water starts running
c. Resetting the Filter’s Counter
1. Click MENU 2. *Scroll to “Change filter/lamp" 3. Click OK
4. *Scroll to “Filter” 5. Click OK 6. *Scroll to “Yes”
7. Click OK 8. Click BACK until the main
screen appears
What does the kit include?
A filter with an extraction tab
How to change the filter
a. Removing the Used Filter and Installing a New Filter with Extraction Tab
1. Remove the rubber pad 2. Press the PUSH button and
pull the filter out
3. Remove the new filter from its
wrapper (make sure that the
extraction tab is attached)
4. Insert the filter until you hear
a click
5. Replace the rubber pad
b. Draining the Air bubble from the New Filter
1. Press the cold water button
(COLD) for 2 minutes
2. Wait for 10 minutes 3. Press the cold waterbutton
again, until water starts running
c. Resetting the Filter’s Counter
1. Click MENU 2. *Scroll to “Change filter/lamp" 3. Click OK
4. *Scroll to “Filter” 5. Click OK 6. *Scroll to “Yes”
7. Click OK 8. Click BACK until the main
screen appears
1. Place Jug under spout
2. 3. 4.
Press the PUSH button,
pull the filter out using the
extraction tab and
discard it
Filter change every 6 months
* In T6 2 button models, scrolling is done using the COLD button only.
2
“REPLACEMENT”Press
Press Press
Press
Press
What does the kit include?
A filter with an extraction tab
How to change the filter
a. Removing the Used Filter and Installing a New Filter with Extraction Tab
1. Remove the rubber pad 2. Press the PUSH button and
pull the filter out
3. Remove the new filter from its
wrapper (make sure that the
extraction tab is attached)
4. Insert the filter until you hear
a click
5. Replace the rubber pad
b. Draining the Air bubble from the New Filter
1. Press the cold water button
(COLD) for 2 minutes
2. Wait for 10 minutes 3. Press the cold waterbutton
again, until water starts running
c. Resetting the Filter’s Counter
1. Click MENU 2. *Scroll to “Change filter/lamp" 3. Click OK
4. *Scroll to “Filter” 5. Click OK 6. *Scroll to “Yes”
7. Click OK 8. Click BACK until the main
screen appears
What does the kit include?
A filter with an extraction tab
How to change the filter
a. Removing the Used Filter and Installing a New Filter with Extraction Tab
1. Remove the rubber pad 2. Press the PUSH button and
pull the filter out
3. Remove the new filter from its
wrapper (make sure that the
extraction tab is attached)
4. Insert the filter until you hear
a click
5. Replace the rubber pad
b. Draining the Air bubble from the New Filter
1. Press the cold water button
(COLD) for 2 minutes
2. Wait for 10 minutes 3. Press the cold waterbutton
again, until water starts running
c. Resetting the Filter’s Counter
1. Click MENU 2. *Scroll to “Change filter/lamp" 3. Click OK
4. *Scroll to “Filter” 5. Click OK 6. *Scroll to “Yes”
7. Click OK 8. Click BACK until the main
screen appears
1. Place Jug under spout
2. 3. 4.
Press the PUSH button,
pull the filter out using the
extraction tab and
discard it
Filter change every 6 months
* In T6 2 button models, scrolling is done using the COLD button only.
2
“REPLACEMENT”Press
Press Press
Press
Press
What does the kit include?
A filter with an extraction tab
How to change the filter
a. Removing the Used Filter and Installing a New Filter with Extraction Tab
1. Remove the rubber pad 2. Press the PUSH button and
pull the filter out
3. Remove the new filter from its
wrapper (make sure that the
extraction tab is attached)
4. Insert the filter until you hear
a click
5. Replace the rubber pad
b. Draining the Air bubble from the New Filter
1. Press the cold water button
(COLD) for 2 minutes
2. Wait for 10 minutes 3. Press the cold waterbutton
again, until water starts running
c. Resetting the Filter’s Counter
1. Click MENU 2. *Scroll to “Change filter/lamp" 3. Click OK
4. *Scroll to “Filter” 5. Click OK 6. *Scroll to “Yes”
7. Click OK 8. Click BACK until the main
screen appears
What does the kit include?
A filter with an extraction tab
How to change the filter
a. Removing the Used Filter and Installing a New Filter with Extraction Tab
1. Remove the rubber pad 2. Press the PUSH button and
pull the filter out
3. Remove the new filter from its
wrapper (make sure that the
extraction tab is attached)
4. Insert the filter until you hear
a click
5. Replace the rubber pad
b. Draining the Air bubble from the New Filter
1. Press the cold water button
(COLD) for 2 minutes
2. Wait for 10 minutes 3. Press the cold waterbutton
again, until water starts running
c. Resetting the Filter’s Counter
1. Click MENU 2. *Scroll to “Change filter/lamp" 3. Click OK
4. *Scroll to “Filter” 5. Click OK 6. *Scroll to “Yes”
7. Click OK 8. Click BACK until the main
screen appears
1. Place Jug under spout
2. 3. 4.
Press the PUSH button,
pull the filter out using the
extraction tab and
discard it
Filter change every 6 months
* In T6 2 button models, scrolling is done using the COLD button only.
1
4
7
2
5
8
3
6
5

Every 12 months - change your UV lamp
Descale your WaterBar and change the lter (as detailed for ‘every 6 months’ on previous
page), then follow these steps to replace the UV lamp.
Leave your WaterBar switched
on. Remove the rubber pad.
Insert the lamp into the device.
Replace the rubber pad.
Pull the lamp upwards and
dispose of it in accordance with
your Local Authority guidelines.
Scroll to New Lamp.
Remove the new lamp from
its wrapper. Avoid touching
the lamp itself.
Press OK.
5
Press
* In T6 2 button models, scrolling is done using the COLD button only.
UV lamp change needs to be performed annually
5
Press
* In T6 2 button models, scrolling is done using the COLD button only.
UV lamp change needs to be performed annually
5
Press
* In T6 2 button models, scrolling is done using the COLD button only.
UV lamp change needs to be performed annually
5
Press
* In T6 2 button models, scrolling is done using the COLD button only.
UV lamp change needs to be performed annually
5
Press
* In T6 2 button models, scrolling is done using the COLD button only.
UV lamp change needs to be performed annually
5
Press
* In T6 2 button models, scrolling is done using the COLD button only.
UV lamp change needs to be performed annually
5
Press
* In T6 2 button models, scrolling is done using the COLD button only.
UV lamp change needs to be performed annually
1
4
7
2
5
3
6
6

Troubleshooting guide
Fault Action to rectify
1Slow water ow Remove and re-insert the lter, making sure it clicks
into place and ts into the lter holder completely
• If the problem persists, contact 0845 301 7700
2Cold water keeps running for a
while after releasing the button
Wait for about 10 minutes and try again
• If the problem persists, contact 0845 301 7700
3The WaterBar will dispense hot
water but not cold water
• Remove and re-insert the lamp
• Unplug and re-connect the device to the
power source
• Press the COLD button for 2 minutes in order
to release the air from the cold water tank
• If the problem persists, contact 0845 301 7700
4Hot and cold water come out
simultaneously
If you press the COLD button but hot water comes out,
dispense hot water for 2-3 minutes and
try again.
If you press the HOT button but cold water comes out,
dispense cold water for 2-3 minutes and
try again.
• If the problem persists, contact 0845 301 7700
7

VIRGIN and the Virgin signature logo are registered trademarks
of Virgin Enterprises Limited.
Any problems?
Contact Customer Services at:
[e-mail]
or call 0845 301 7700
Henley Business Park
Pirbright Road
Guildford
Surrey
GU3 2DX
www.virginpure.com