Visa Lighting LATITUDE Series User manual

LATITUDE
CM2104-T
CM2104-W
CM2104-D
CM2106-T
CM2106-W
CM2106-D
CM2108-T
CM2108-W
CM2108-D
Drawing:
762298XX
Rev:
B
Sheet:
1 of 4
Eng:
DMM
Date Drawn:
1/18/19
INSTALLATION INSTRUCTIONS
Model: CM2104-T,-W,-D, CM2106-T,-W,-D, CM2108-T,-W,-D
Fixture Family: LATITUDE
1717 West Civic Drive Milwaukee, WI 53209
414-354-6600
Design Modification Rights Reserved
© Visa Lighting 2018
!
When using electrical equipment, basic safety precautions should always be followed, including the following:
Read all instructions carefully before installing and save for future use. •
Make sure all connections are in accordance with the National Electrical Code and local regulations. •
To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture •
Service should be performed by qualified personnel. •
These instructions may not cover all details or variations. If additional information is needed, please contact Visa Lighting. •
Document Description: Installation Instructions for
LATITUDE Series Luminaires

FIXTURE
HOUSING
FIXTURE
MOUNITNG
SCREWS (8)
CONDUIT
CONNECTOR (2)
(by others)
T-GRID MOUNTING
BRACKET (3)
(sold separately)
T-GRID INSTALLATION
ENDCAP
BOTTOM LENS
T-GRID ASSEMBLY
(by others)
2"
2-1/2"
ADDITIONAL MOUNTING
BRACKETS
(12" FOR 6FT MODEL)
(20" FOR 8FT MODEL)
CONDUIT FITTING
KNOCKOUTS
CENTER
MOUNTING
PLATE
Remove bottom lens from fixture housing. 1.
Remove fixture mounting screws from fixture housing. This will detach the end mounting brackets and center mounting 2.
plate from the fixture housing. Refer to page 3 for mounting dimensions.
Install T-Grid mounting brackets. These are either 'by others' or were purchased with the fixture(s). To install the T-Grid 3.
mounting to the end brackets, refer to page 4 for instructions.
Install the fixture housing by supporting the fixture to the ceiling. Make sure to line up the holes on the standoffs located on 4.
the end brackets. Secure with mounting screws.
Reinstall the bottom lens. 5.
T-GRID MOUNTING HOLE DIMENSIONS
Drawing:
762298XX
Rev:
B
Sheet:
2 of 4
Eng:
DMM
Date Drawn:
1/18/19
INSTALLATION INSTRUCTIONS
Model: CM2104-T,-W,-D, CM2106-T,-W,-D, CM2108-T,-W,-D
Fixture Family: LATITUDE
1717 West Civic Drive Milwaukee, WI 53209
414-354-6600
Design Modification Rights Reserved
© Visa Lighting
!
When using electrical equipment, basic safety precautions should always be followed, including the following:
Read all instructions carefully before installing and save for future use. •
Make sure all connections are in accordance with the National Electrical Code and local regulations. •
To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture •
Service should be performed by qualified personnel. •
These instructions may not cover all details or variations. If additional information is needed, please contact Visa Lighting. •
Document Description: Installation Instructions for
LATITUDE Series Luminaires

JUNCTION
BOX SCREWS
(by others)
WALL ANCHORS
(by others)
CENTER
MOUNTING
PLATE
MOUNTING
SURFACE
FIXTURE
HOUSING
FIXTURE
MOUNITNG
SCREWS (8)
BOTTOM LENS
ENDCAP
FIXTURE
TETHER
MOUNTING
SCREWS
(by others)
FIXTURE
TETHER
ADDITIONAL MOUNTING
BRACKETS
(12" FOR 6FT MODEL)
(20" FOR 8FT MODEL)
36" 22"
3-1/2"
5"
CENTER
MOUNTING
PLATE
Remove the end cap by removing the (4) Allen screws. Set end cap aside. 1.
Remove bottom lens from fixture housing by sliding out the side of fixture. 2.
Remove fixture mounting screws from fixture housing. This will detach the additional mounting brackets and center 3.
mounting plate from the fixture housing.
Install center mounting plate and additional end mounting brackets to mounting surface (8FT model only). Use anchors 4.
(by others), to help secure the center mounting plate and end mounting brackets to mounting surface. See above for
mounting dimensions.
Install the fixture tethers as shown in above diagram. 5.
Install the fixture housing by installing the fixture mounting screws. 6.
Reinstall the bottom lens and end cap. 7.
SHEETROCK INSTALLATION
SHEETROCK MOUNTING HOLE DIMENSIONS
Drawing:
762298XX
Rev:
B
Sheet:
3 of 4
Eng:
DMM
Date Drawn:
1/18/19
INSTALLATION INSTRUCTIONS
Model: CM2104-T,-W,-D, CM2106-T,-W,-D, CM2108-T,-W,-D
Fixture Family: LATITUDE
1717 West Civic Drive Milwaukee, WI 53209
414-354-6600
Design Modification Rights Reserved
© Visa Lighting
!
When using electrical equipment, basic safety precautions should always be followed, including the following:
Read all instructions carefully before installing and save for future use. •
Make sure all connections are in accordance with the National Electrical Code and local regulations. •
To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture •
Service should be performed by qualified personnel. •
These instructions may not cover all details or variations. If additional information is needed, please contact Visa Lighting. •
Document Description: Installation Instructions for
LATITUDE Series Luminaires

T-GRID CLIP
ADDITIONAL MOUNTING BRACKET
2 PER FIXTURE
(6FT AND 8FT MODELS ONLY)
T-GRID CLIP FASTENER
STANDOFF
Install T-Grid clip onto the T-Grid (by others). 1.
Refer to page 3 for the proper spacing of the clips. 2.
Install additional mounting bracket onto the T-Grid clip. 3.
Secure with T-Grid clip fastener. Do not over tighten. Doing so can damage the clip fastener. 4.
Follow further T-Grid installation on page 2. 5.
Drawing:
762298XX
Rev:
B
Sheet:
4 of 4
Eng:
DMM
Date Drawn:
1/18/19
INSTALLATION INSTRUCTIONS
Model: CM2104-T,-W,-D, CM2106-T,-W,-D, CM2108-T,-W,-D
Fixture Family: LATITUDE
1717 West Civic Drive Milwaukee, WI 53209
414-354-6600
Design Modification Rights Reserved
© Visa Lighting
!
When using electrical equipment, basic safety precautions should always be followed, including the following:
Read all instructions carefully before installing and save for future use. •
Make sure all connections are in accordance with the National Electrical Code and local regulations. •
To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture •
Service should be performed by qualified personnel. •
These instructions may not cover all details or variations. If additional information is needed, please contact Visa Lighting. •
Document Description: Installation Instructions for
LATITUDE Series Luminaires