Vision TM-WB User manual

1
TM-WB_manual_en
TM-WB OWNERS MANUAL

2
TM-WB_manual_en
www.visionaudiovisual.com/techmount/tm-wb

3
TM-WB_manual_en
DECLARATION OF CONFORMITY
Where applicable Vision products are certified and comply with all known local regulations to a
‘CB Certification’ standard. Vision commits to ensure all products are fully compliant with all
applicable certification standards for sale in the EU and other participating countries.
The product described in this owner manual is in compliance with RoHS (EU directive
2002/95/EC), and WEEE (EU directive 2002/96/EC) standards. This product should be returned
to the place of purchase at the end of its useful life for recycling.
WARNINGS
During installation take care to adhere to workplace health and safety laws:
Do not cut or drill any parts above head height. This should all be done using the correct
safety equipment at floor level.
Avoid overstretching which might result in the ladder tipping over.
SWL (safe working load): Projector: 10kg, Whiteboard / Flat Panel: 50kg
Ensure it is installed in an appropriate place –for example not obstructing an emergency exit.
IN THE LOWEST POSITION THE BOOM AND PROJECTOR CAN PRESENT A
HEAD HEIGHT HAZARD
Check stability after installation.
Installation must be done by a specialist audio-visual installer
Allow 500mm x 500mm space around the bracket.
Avoid installing in a moist environment, or in direct sunshine, or near corrosive gas or liquid.
Routing of cables through the bracket must comply with local regulations.
ENSURE POWER CABLE IS NOT TWISTED, SQUEEZED, OR SHEARED!
All products are designed and imported into the EU by ‘Vision’ who is wholly owned by ‘Azlan
Logistics Ltd.’, Registered in England Nr. 04625566 at Lion House, 4 Pioneer Business Park,
Clifton Moor, York, YO30 4GH. WEEE Registration: GD0046SY
DECLARATION OF ORIGIN
All Vision products are made in the People’s Republic of China (PRC).

4
TM-WB_manual_en
ACCESSORIES

5
TM-WB_manual_en
INSTALLATION
1. ATTACH LEGS TO WALL Use spirit level to ensure legs are plumb. Route cables at same
time.
ALTERNATIVE USING STAND-OFFS
Ensure the correct fixtures are used to attach the Techmount to the wall.
The fixtures provided may not be suitable for your application.
NOTE: At least six fixtures must be used for each leg, with two at the top.

6
TM-WB_manual_en
2. HANG FRAME ON LEGS
3. FIT BRACKETS to side of frame as shown. Add locking screws to prevent frame being lifted
off legs.
Locking screwsLocking screws

7
TM-WB_manual_en
4. ATTACH UPRIGHT
5. ATTACH BOOM

8
TM-WB_manual_en
6. ATTACH SPIDER TO PROJECTOR
7. FIT PROJECTOR ASSEMBLY TO BOOM Tighten screw to lock the two parts of the boom
together

9
TM-WB_manual_en
8. FIT ADJUSTABLE ARMS TO WHITEBOARD / FLAT PANEL
9. HANG BOARD ON FRAME Make projector level and turn on. Set projector zoom as large as
possible. Adjust boom length so image is same size as board. Hang board at same height
as image.

10
TM-WB_manual_en
10. TEST EXCURSION Plug motor into power and move assembly to upper and lower limits to
ensure no snags and mount is operating safely.
Adjustments may be necessary. Once complete tighten all bolts.
SPECIFICATIONS
PRODUCT WEIGHT: 40.5 kg
SAFE WORKING LOAD:
Interactive Whiteboard / Touch-panel LCD: 50 kg
Projector: 10 kg
CONTRUCTION MATERIAL: Aluminium and Steel
COLOUR: White and Aluminium
TECHNICAL DETAILS:
Motor Type: Linear-drive
Rated Cycles: 12000
Speed: 25mm/s
Pushing Force: 2000N
Pulling Force: 1800N
ACCESSORIES:
1 x EU Figure-8 Power cable 1.8m long
1 x UK Figure-8 Power cable 1.8m long

11
TM-WB_manual_en
WARRANTY
This product comes with a 2-year return to base warranty, effective from the date of purchase.
This warranty applies only to the original purchaser and is not transferable. For the avoidance of
doubt, this will be taken from the information held by the appointed national distributor at the
point of sale. The liability of the manufacturer and its appointed service company is limited to
the cost of repair and or replacement of the faulty unit under warranty, except for death or
injury (EU85/374/EEC). This warranty protects you against the following:
Faulty welds resulting in the product not safely performing its task within the recommended
SWL (safe working load).
Poor finishing resulting in the product not being able to be assembled.
External corrosion if identified within 24 hours of purchase. The inside of the pipe is not
powder-coated, so light corrosion may develop over time. This is normal and does not
adversely affect the load-bearing capability of the product, therefore it is not covered in this
warranty.
If you find you do have a problem with this product, you should contact the AV reseller you
purchased this product from. The original purchaser is responsible for shipment of the product
to the manufacturer’s appointed service centre for repair. We will endeavour to return repaired
units within 5 working days, however this may not always be possible in which case it will be
returned as soon as practically possible. This warranty does not protect this product against
faults caused by abuse, misuse, or incorrect installation which might be caused by ignoring the
guidelines set out in this manual. If failure is not covered by this warranty, the owner will be
given the option to pay for labour and parts to repair the unit at the service company’s standard
rate.
LEGAL DISCLAIMER: Because we are committed to improving our products, the details above
may change without prior warning. This User Manual is published without warranty and any
improvements or changes to the User Manual necessitated by typographical errors, inaccuracies
of current information, or improvements to programs and/or equipment, may be made at any
time and without notice. Such changes will be incorporated into new editions of the User
Manual.