VISIONARY DESIGNS MOD-1232 Manual

© 2017
Order #XXXXX
SETUP INSTRUCTIONS
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
MOD-1232 Workstation
Top View
Front View

© 2017
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all setscrews
and locks during disassembly
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information

© 2017
Order #XXXXX
Step 1 of 2
Workstation Assembly
Steps
1)
Attach horizontals [5] and [6] between verticals [1] [2] [3] and [4].
Note: bottom of horizontals [6] should be on top of stoppers and 4” from floor.
2) Set Floor onto lips of horizontals [6].
3) Slide infill panels between verticals [1] [2] [3] and [4].
4) Attach horizontal extrusions [7] [8] and [9] between verticals [1] [2] [3] [4]
and on top of infills and door.
5) Connect vertical [10] between horizontal extrusions [8].
1
1
4
3
2
3
4
5
6
5
6
Extrusions [6]
have a lip for the
floor to rest
upon.
4”
7
8
98
9
Floor
Infill
Infill
Door
Stopper
10
Connectors for
Monitor Mount
Attachment
Door
Hinge
Hinge
Pin
Slide pin into
hinge attached
to vertical.
Slide door
hinge over pin.
Door Connection
*
Item
1
2
3
4
5
6
7
8
9
10
Qty.
1
1
1
1
2
2
1
2
2
1
Description
36”h Vertical Extrusion w/ Door Hinges
36”h Vertical Extrusion w/ Door Stop
36”h Vertical Extrusion
36”h Vertical Extrusion
19”w Horizontal Extrusion
23”w Horizontal Extrusion
19”w Horizontal Extrusion
8.87”w Horizontal Extrusion
23”w Horizontal Extrusion
42.8”h Vertical Extrusion
Infill
2

© 2017
Order #XXXXX
Step 2 of 2
Workstation Assembly (Cont’d)
2-piece Counter Top
Steps
1)
Velcro shelf supports to inside of assembled base.
2) Set internal shelf on top of supports.
3)
Slide counter top on vertical extrusion [10] and set
on assembled base.
4) Attach graphics to extrusions [10] & [1] [4].
See Graphic Attachment detail.
5) Attach literature holders to extrusion [4].
See Literature Holder Attachment detail.
6) Attach monitor mount to extrusion [10].
See Monitor Mount detail.
Internal
Shelf
10 10
4
1
Connector
Literature Holder Attachment
Locks
Literature
Holder
Attach angled end of Connector to
Literature Holder. Attach flat end of
Connector to vertical extrusion.
Tighten locks to secure.
*
*
Connector
Graphic Attachment
Cap
Graphic
Standoff
Slide Connector into groove of extrusion.
Tighten set screws to secure in place.
Screw Standoff into Connector. Place
Graphic between Standoff and Cap,
then screw Cap to tighten in place.
Monitor Mount
V4 Connectors
*
Slide connectors into groove
of extrusion. Tighten set screws
to secure connectors in place.
Attach monitor mount back
plate to extrusion, using bolts.
Bolts
Monitor
Mount
*
*
**
*