Vista 12V Series User manual

INSTALLATION INSTRUCTIONS In-Ground and Well Lights
5270
Main supply cable
Silicone filled
safety connectors 36" Pigtail
Lens
Stainless steel screw
Fixture housing
Pea Gravel
Soil
TOOLS REQUIRED FOR
INSTALLATION:
●Wire strippers
●Blade head screwdriver
●Shovel
FOR USE ONLY WITH LOW VOLTAGE LANDSCAPE POWER UNITS THAT DO NOT EXCEED 25 AMPS, 15 VOLT MAXIMUM.
WARNING: Luminaires must be installed in accordance with the National Electrical Code (NEC) and local codes.
Failure to do so will void the warranty and may result in serious injury and/or damage to the luminaire.
SAFETY WARNING: Luminaire can become very hot depending on lamp wattage used. Lens and metal around
lamp can become hot enough to blister hands. Particular care should be taken not to locate luminaires where
small children can reach them if high wattage lamps are used.
LUMINAIRES ARE NOT TO BE INSTALLED WITHIN 10 FT. (3.05M) OF A POOL OR SPA. SECONDARY CABLE IS NOT TO
BE BURIED MORE THAN 6”. WHEN USING MULTIPLE LUMINAIRES, LOAD IS NOT TO EXCEED THE TOTAL WATTS OF
TRANSFORMER RATING. DO NOT USE EXTENSION CORDS ON POWER UNITS.
NOTE: Always use UL recognized wire connectors for connections.
NOTE: Save these instructions for future reference.
LUMINAIRE IS UL LISTED FOR ABOVE GROUND INSTALLATION ONLY.
LUMINAIRE MOUNTING:
PRECAUTION: Luminaire is not submersible and adequate drainage must be provided during installation. It is recommended
that the luminaire be surrounded by 3” to 4” of pea gravel or sand to assure proper drainage. Top of luminaire must be
above grade so rain and irrigation water can not accumulate for long periods of time.
1. To prevent electrical shock, disconnect transformer from electrical supply before installation or service.
2. Dig hole approximately 10” diameter by 8” deep. This allows approximately 3” of pea gravel or sand to surround the
luminaire housing.
3. Strip the (2) leads from the luminaire pigtail wire. Using the two (2) silicone lled safety connectors (provided), connect the
leads from the luminaire to the main supply cable leads.
NOTE: Luminaires are supplied with 36” of 18-2 cable pigtail for secure connection to the main supply cable. The wire is to
be protected by routing in close proximity to the luminaire. The wiring shall be buried a maximum of 6 inches
(15.2 cm) in order to connect to the main supply cable.
4. Install luminaire in hole and backll hole after installation with pea gravel or sand.
5. Provide power to luminaire and check for proper operation.
12V SERIES
1625 Surveyor Avenue • Simi Valley, CA 93063 • [phone] • (800) 766-VISTA (8478)
FAX: (888) 670-VISTA (8478) • [email protected] • www.vistapro.com
In-Grade Soil Installation:

LAMP INSTALLATION/REPLACEMENT:
CAUTION: Do not exceed maximum wattage marked on luminaire label.
1. To prevent electrical shock, disconnect transformer from electrical supply before service.
2. Loosen the ve (5) cover screws and remove cover.
3. Remove gasket.
4. Replace lamp with correct wattage and type marked on xture label.
NOTE: DO NOT touch Halogen lamp with bare hands. Always use soft cloth or the plastic wrapping (if available) from the
lamp to handle the lamp.
5. Clean gasket and channel and re-install gasket.
6. Re-install cover and tighten the ve (5) screws evenly.
1625 Surveyor Avenue • Simi Valley, CA 93063 • [phone] • (800) 766-VISTA (8478)
FAX: (888) 670-VISTA (8478) • [email protected] • www.vistapro.com
Lens
Stainless
steel screw
Rigid conduit
Concrete
pour kit
Flexible conduit
(Recomended)
Fixture housing
Concrete
Soil
TOOLS REQUIRED FOR
INSTALLATION:
●Wire strippers
●Blade head screwdriver
●Shovel
●Teon tape
●Pipe sealer
LUMINAIRE MOUNTING:
1. To prevent electrical shock, disconnect transformer from electrical supply before installation or service.
2. Dig hole approximately 10” diameter to a depth suitable to make top of xture ush to 1/8” above grade. Pea gravel or
sand is recommended for seating the luminaire housing to aid positioning.
3. Install JBCP-150 concrete mounting guard making sure the top edge of the ring lines up with the top edge of the lens
cover. Secure side bands to the bottom of xture with #10 screws provided. (Side bands of JBCP-150 may be bent outward
to adjust the t of the top ring.)
4. Install conduit through 3/4” NPT holes in bottom of luminaire using Teon tape or other thread sealant. Using plug
(provided), seal unused conduit entry if required.
NOTE: UL listed exible conduit is recommended for in and out connections to ease xture position and adjustment during
installation.
5. Support luminaire in selected position using standard masonry procedures.
NOTE: When installing in concrete, JBCP-150 must be ush to 1/8” above grade to promote water runoff.
6. Pull supply wires (line in), through conduit into luminaire wire compartment.
8. Wire luminaire as required using silicone lled safety connectors (provided).
9. Pour concrete at least 2” thick.
10. Install lamp with correct wattage and type marked on the xture label and set lamp at desired aiming angle.
11. Replace silicone rubber gasket, lens, and cover, and tighten screws evenly.
NOTE: Failure to remove all dirt and debris from gasket sealing surface may cause leakage and void the warranty.
Concrete Pour Installation:
IMPORTANT SAFETY INSTRUCTIONS
THE LIGHTED LAMP IS HOT!!
WARNING: TO REDUCE THE RISK OF FIRE, OR INJURY TO
PERSONS:
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamps get hot quickly! Contact only switch/plug when turning on.
3. Do not touch hot lens, guard or enclosure.
4. Keep lamp away from material that may burn.
5. Do not touch the lamp at any time. Use a soft cloth. Oil from the skin may damage lamp.
6. Do not operate luminaire tting with a missing or damaged cover.
SAVE THESE INSTRUCTIONS
NOTE:
Lamp bracket may
be adjusted for
lamp aiming. Loosen
bracket screws (1),
then manually tilt
bracket (2) to desired
position. Tighten
bracket screws
afterward to secure
lamp position.
1
2