Vista VLI-4ED28V12IRQ User manual

VLI-4ED28V12IRQ
Quick Start Guide
1 Warning and Caution
■ If the product does not work correctly, please contact Technical
Support via the details over the page. Never attempt to disassemble the
camera yourself. (We shall not be responsible for any problems caused
by unauthorized repair or maintenance.)
■ In the use of the product, you must adhere to compliance with
electrical safety regulations of your nation and region. When the
product is mounted on wall or ceiling, the device shall be firmly
fixed.
■ Do not allow water or liquid intrusion into the camera.
■ Do not use camera beyond specified voltage range.
■ Do not drop the camera or subject it to physical shock.
■ Avoid touching the camera lens.
■ If cleaning is necessary, please use clean cloth to wipe it gently.
■ Do not aim the camera at direct sunlight.
■ Do not place the camera in extremely hot, cold (operating
temperature is -30˚C~60˚C), dusty or damp locations and do not
expose it to high electromagnetic radiation.
■ To avoid heat accumulation, good ventilation is required for
operating environment.
2 Package
3 Overview
1
2
3
5
* It is recommended y ou install the security cap for outdoor installation.
* If a PoE switch is used to power the camera, DC12V power supply is
not required.
Connecting Network Cable
1
① Loosen the nut from the main adapter.
②Pass the network cable (before RJ45 connector crimping)
through both parts of the connector, then crimp.
③Plug in the new RJ45 plug into the hermetic connector. Tighten the
nut and the main cover.
4 Installation
Please make sure that the wall or ceiling is strong enough to
withstand 3 times the weight of the camera. Please install the
camera into a dry environment.
①Loosen the fixed screw to disassemble the camera.
②Open the cover of the dome and then insert a micro SD card, if
required. Re-install the cover.
Please read this g u id e carefully before operating the unit
and keep it for further reference.
All examples and pictures used here are for reference only.
The contents of this guide are subject to change without
notice.
Camera
Quick start guide
Tapping screw ×4
Screwdriver
Drill template
Plastic plug ×4
1
2
3
4
5
6
7
8
Ethernet connector
Audio input connector
Power connector
Mounting base
Fixed screw
Microphone
Micro SD card slot
Reset(hold 5 secs)
4
6

Note: *Check the waterproof ring on the card slot cover is
installed properly before installing the cover back.
*Please install the cover in the same way you disassemble it, so
that the sealing performance will not be affected.
③Drill the screw holes and the cable access hole in the wall according
tothe drill template below.
(MM)
④Route and connect the cables. Then secure the mounting base to
theceiling or wall with the screws provided
⑤Install the dome and enclosure to the mounting base and then
adjust the dome to obtain an optimum view angle
⑥Finally, tighten the fixed screw and make sure the camera is
fixed firmly.
5 Network Connection
①Make sure the camera and PC are connected via the same VLAN.
②Download the IP-Tool from the Vista website via the QR
code and install on to the PC. Run the IP-Tool as shown below.
③Double click the required camera listed in the IP-Tool to open
web browser access to it. Or manually enter the default IP address in
the address bar of your browser.
The default IP address of this camera is 192.168.226.201.
Follow directions to download and install any required plugin if it is
the first time logging into the camera.
④Activate and log in to the camera - default username is admin;
default password is 123456. Set a new password for security.
Make any configuration changes necessary.
Customer Support
For assistance in installing, operating, maintaining and troubleshooting
this product refer to this document and any other documentation provided
via the QR code below etc. If you still have questions, please contact
Norbain Technical Support and Sales:
Norbain SD, Inspired, Easthampstead Road,
Bracknell , Berkshire RG12 1YQ.
UK [phone]
Note: You should be at the equipment and ready with details before
calling Technical Support.
Our CE EU-Authorised Representative: Comply Express Unipessoal
LDA, StartUp Madeira - EV141, Campus da Penteada, 9020-105 Funchal,
Madeira, Portugal”
NORBAIN SD reserves the right to make changes to the product and
specification of the product from time to time without prior notice.
VLI-4ED28V12IRQ - Quick Guide V1.0 2022-05-26
Ø79.
Ø5.0
Switch
Network Cable
Network Cable
IPC
Router
Computer