Vista VK2-1080XVRDPTZ User manual

VK2-1080XVRDPTZ
User Manual

VK2-1080XVRDPTZ User Manual V1.0 2
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO
NOT INSERT ANY METALLIC OBJECTS THROUGH THE
VENTILATION GRILLS OR OTHER OPENINGS ON THE
EQUIPMENT.
CAUTION
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.

VK2-1080XVRDPTZ User Manual V1.0 3
CE COMPLIANCE STATEMENT
WARNING
This is a Class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED
BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING
TO THE INSTRUCTIONS.

VK2-1080XVRDPTZ User Manual V1.0 4
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves,
or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding
type plug has two blades and a third grounding prong. The wide blade or the
third prong is provided for your safety. If the provided plug does not fit into
your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when
the apparatus has been damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
15. CAUTION –THESE SERVICING INSTRUCTIONS ARE FOR USE BY
QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF
ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN
THAT CONTAINED IN THE OPERATING INSTRUCTIONS UNLESS YOU
ARE QUALIFIED TO DO SO.
16. Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed
Class 2 power source only.
17. ITE is to be connected only to PoE networks without routing to the outside
plant.

VK2-1080XVRDPTZ User Manual V1.0 5
TABLE OF CONTENTS
1. Description....................................................................................................................7
1.1 Components .......................................................................................................................7
1.2 Key Features.......................................................................................................................8
2. Installation.....................................................................................................................9
2.1 Installation ..........................................................................................................................9
2.2 Basic Configuration of Camera System..........................................................................11
2.3 Connections......................................................................................................................12
2.4 Network Connection & IP assignment ............................................................................13
3. Operation.....................................................................................................................14
3.1 Access from a browser....................................................................................................14
3.2 Access from the internet..................................................................................................15
3.3 Setting the admin password over a secure connection ................................................15
3.4 Live View Page .................................................................................................................16
3.5 VK2-1080XVRDPTZ Setup................................................................................................18
3.5.1 Basic Configuration...................................................................................................18
1) Users............................................................................................................................19
2) Network........................................................................................................................20
3) Video & Image .............................................................................................................21
4) Audio............................................................................................................................23
5) Date & Time .................................................................................................................24
3.5.2 Live View ....................................................................................................................25
3.5.3 Video & Image............................................................................................................25
1) Basic ............................................................................................................................25
2) Image............................................................................................................................26
3) Auto Exposure.............................................................................................................27
4) Day & Night..................................................................................................................28
5) Auto Focus ..................................................................................................................29
6) DIS................................................................................................................................30
7) Webcasting..................................................................................................................30
3.5.4 Audio ..........................................................................................................................31
3.5.5 Event...........................................................................................................................31
1) Event In........................................................................................................................31
2) Event Out.....................................................................................................................35
3) Event Map....................................................................................................................41
3.5.6 Dome Configuration...................................................................................................43
1) Preset...........................................................................................................................43

VK2-1080XVRDPTZ User Manual V1.0 6
2) Tour..............................................................................................................................44
3) Motor Setup.................................................................................................................45
4) RS485...........................................................................................................................46
5) View Angle...................................................................................................................46
6) System Menu...............................................................................................................47
7) Privacy Zone................................................................................................................48
3.5.7 System........................................................................................................................49
1) Information ..................................................................................................................49
2) Security........................................................................................................................49
3) Date & Time .................................................................................................................51
4) Network........................................................................................................................52
5) Language.....................................................................................................................60
6) Maintenance ................................................................................................................61
7) Support........................................................................................................................62
3.6 Help ...................................................................................................................................64
3.7 Resetting to the factory default settings.........................................................................64
4. Appendix .....................................................................................................................65
4.1 Troubleshooting...............................................................................................................65
4.2 Alarm Connection.............................................................................................................66
4.3 Preventive Maintenance...................................................................................................66
4.4 Product Specification.......................................................................................................67
4.5 System Requirement for Web Browser...........................................................................70
4.6 General Performance Considerations.............................................................................70

VK2-1080XVRDPTZ User Manual V1.0 7
1. Description
This manual applies to the VK2-1080XVRDPTZ full HD PTZ vandal resistant day/Night dome.
1.1 Components
The VK2-1080XVRDPTZ is designed with compact, small size, hard dome camera housing. The
housing is constructed of aluminum, steel and plastic. The housing is designed to be mounted on a
wall or a ceiling. The housing meets the Protection Classification IP66 standards for dust and
moisture resistance.
* Dome Camera 1
* Installation Guide/CD 1
* Template Sheet 1
* Mounting Bracket 1
* Safety Lanyard 1
* RJ-45 Coupler 1
* Accessory Kit 1
1) Mounting screws (PH6 x 35.0) (4)
2) Plastic anchors (4)
3) O-Rings (4)
4) Torx wrench (1)
* Accessory Connector 1
1) 3-pin terminal block (1)
2) 6-pin terminal block (1)

VK2-1080XVRDPTZ User Manual V1.0 8
1.2 Key Features
Brilliant video quality
The VK2-1080XVRDPTZ offers the highly efficient H.264 video compression, which drastically
reduces bandwidth and storage requirements without compromising image quality. Motion
JPEG is also supported for increased flexibility.
Triple Streams
The VK2-1080XVRDPTZ can deliver triple video streams simultaneously at full frame rate in
all resolutions up to 1920 x 1080 using Motion JPEG and H.264. This means that several
video streams can be configured with different compression formats, resolutions and frame
rates for different needs.
Image setting adjustment
The VK2-1080XVRDPTZ also enables users to adjust image settings such as contrast,
brightness and saturation to improve images before encoding takes place.
Intelligent video capabilities
The VK2-1080XVRDPTZ includes intelligent capabilities such as enhanced video motion
detection. The network camera’s external inputs and outputs can be connected to devices
such as sensors and relays, enabling the system to react to alarms and activate lights or
open/close doors.
Improved Security
The VK2-1080XVRDPTZ logs all user access, and lists currently connected users. Also, its full
frame rate video can be provided over HTTPS.
PoE (Power over Ethernet)
This VK2-1080XVRDPTZ can be powered through PoE, which simplifies installation since only
one cable is needed for carrying power, as well as video controls.
ONVIF Certificate
This is a global interface standard that makes it easier for end users, integrators, consultants,
and manufacturers to take advantage of the possibilities offered by network video technology.
ONVIF enables interoperability between different vendor products, increased flexibility,
reduced cost, and future-proof systems.

VK2-1080XVRDPTZ User Manual V1.0 9
2. Installation
2.1 Installation
The dome camera is for use in surface or pendant mounting applications, and the mounting
position must be capable of supporting loads of up to 3.5 lb (1.6 kg). (Pendant mounting must use
pendant mount accessory.)
The dome camera’s mounting bracket should be attached to a structural object, such as hard wood,
wall stud or ceiling rafter that supports the weight of the dome camera.
CAUTION: A silicone rubber sealant must be applied to seal the housing to secure
waterproofing.
2.1.1 Locking Dome Camera
A. Make screw holes on the ceiling using the supplied mounting Template Sheet (Figure A).
B. Fix the Mounting Bracket to the ceiling using supplied Anchors (4x) and Mounting Screws (4x)
(Figure B).
C. Hook up the Safety Lanyard to the Safety Lanyard Hook of the Mounting Bracket (Figure C).
D. Align the locking tab on the bracket and the locking slot on the base of the dome (Figure D).
E. Turn the dome to the counterclockwise about 10 degree to the locked position (Figure E).

VK2-1080XVRDPTZ User Manual V1.0 10
CAUTION: Before installing mounting bracket to surface pre-adjust the four mounting
screws "A" on the base of the dome camera to best match the mounting
bracket locked position. Unscrew the locking screw on the side of the dome's
base and fit the tab of the mounting bracket into the locking slot. Screws "A"
should not be too tight or too loose when the dome is in the locked position.
After setting the proper positions of screws "A" remove the mounting bracket
and install it to the proper surface. If it is too difficult to lock the dome in
position after the mounting bracket has been installed readjust the screws "A"
by unscrewing them a small amount and try to install dome camera again.

VK2-1080XVRDPTZ User Manual V1.0 11
2.2 Basic Configuration of Camera System
No.
Connector
Wire Color
Description
1
3-pin terminal block
RED
24VAC or 12VDC+
WHITE
24VAC or 12VDC-
2
6-pin terminal block
PINK
GND
GRAY
ALARM INPUT
BROWN
GND
YELLOW
ALARM OUTPUT
GREEN
RS485+
BLUE
RS485-
3
RJ-45
BLACK
Ethernet, RJ-45 port compatible with
10/100Mbps having PoE functionality.
4
STEREO
GRAY
AUDIO OUTPUT
5
STEREO
BLACK
AUDIO INPUT
The camera must be installed by qualified service personnel in accordance with all local electrical
and building codes.
AC+ AC- AC+ AC- FGND (Rx+) (Rx-) Rx(Tx)+ Rx(Tx)- GND

VK2-1080XVRDPTZ User Manual V1.0 12
2.3 Connections
Connecting the Network
Connect a standard RJ-45 cable to the network port of the camera. Generally a cross-over
cable is used for directly connection to PC, while a direct cable is used for connection to a
switch.
Connecting Alarms
- AI (Alarm Input)
You can use external devices to signal the camera to react on events. Mechanical or
electrical switches can be wired to the AI (Alarm Input) and G (Ground) connectors.
- G (Ground)
NOTE: All the connectors marked G or GND are common.
Connect the ground side of the alarm input and/or alarm output to the G (Ground) connector.
- AO (Alarm Output)
The camera can activate external devices such as buzzers or lights. Connect the device to
the AO (Alarm Output) and G (Ground) connectors.
Connecting to the RS485
The camera can be controlled remotely by an external device or control system, such as a
control keyboard, using RS485 half-duplex serial communications signals.
Connecting the Power
Connect power of 12VDC or 24VAC 1.5A for the camera.
When using a 12VDC adapter, connect the positive (+) pole to the ‘+’ position and
the negative (-) pole to the ‘-’ position.
Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class 2 power source only.
- Be careful not to reverse the polarity when you connect the power cable.
- You can also use a router featuring PoE (Power over Ethernet) to supply power to the
camera.
- If PoE and 12VDC are both applied, this camera will get supplied with power from PoE.
- 24VAC is recommended to use for the camera power for stable operation with heater kit.
If using PoE, the heater will not operate at all.

VK2-1080XVRDPTZ User Manual V1.0 13
2.4 Network Connection & IP assignment
The camera supports the operation through the network. When a camera is first connected to the
network, it is necessary to allocate an IP address to the device with the “SmartManager” utility on
the CD. (Default IP 192.168.30.220)
1) Connect the network camera/device to the network and power up.
2) Start SmartManager utility (Start > All programs > SmartManager > SmartManager). The main
window will display, and after a short while any network devices connected to the network will
be displayed in the list.
3) Select the camera on the list and click right button of the mouse. You can see the pop-up
menu as below.
4) Select Assign IP Address. The Assign IP window will display. Enter the required IP address.
NOTE: More if multiple cameras are selected then a range of Ip addresses can be configured.
For more information, refer to the SmartManager User’s Manual.

VK2-1080XVRDPTZ User Manual V1.0 14
3. Operation
The VK2-1080XVRDPTZ can be used with Windows® operating system and browsers. The
recommended browsers are Internet Explorer®, Safari®, Firefox®, Opera™ and Google®
Chrome® with Windows.
NOTE: To view streaming video in Microsoft Internet Explorer, set your browser to allow ActiveX
controls.
3.1 Access from a browser
1) Start a browser (Internet Explorer).
2) Enter the IP address or host name of the in the Location/Address field of your browser.
3) You can see a starting page. Click Live View or Setup to enter web page.
4) The network camera’s Live View page appears in your browser.

VK2-1080XVRDPTZ User Manual V1.0 15
3.2 Access from the internet
Once connected, the VK2-1080XVRDPTZ is accessible on your local network (LAN). To access
the VK2-1080XVRDPTZ from the Internet you must configure your broadband router to allow
incoming data traffic to the network camera. To do this, enable the NAT traversal feature, which
will attempt to automatically configure the router to allow access to the network camera. This is
enabled from Setup > System > Network > NAT. For more information, please see “3.5.7 System >
Network > NAT” of User's Manual.
3.3 Setting the admin password over a secure connection
To gain access to the product, the password for the default administrator user must be set. This is
done in the “Admin Password” dialog, which is displayed when the VK2-1080XVRDPTZ is
accessed for the setup at the first time. Enter your admin name and password, set by the
administrator.
NOTE: The default administrator user name and password is “admin”. If the password is lost, the
must be reset to the factory default settings. Please see “Resetting to the factory default
settings”.
To prevent network eavesdropping when setting the admin password, this can be done via an
encrypted HTTPS connection, which requires an HTTPS certificate (see NOTE below).
To set the password via a standard HTTP connection, enter it directly in the first dialog shown
below. To set the password via an encrypted HTTPS connection, please see “3.5.7 System >
Security > HTTPS” of User's Manual.
NOTE: HTTPS (Hypertext Transfer Protocol over SSL) is a protocol used to encrypt the traffic
between web browsers and servers. The HTTPS certificate controls the encrypted
exchange of information.

VK2-1080XVRDPTZ User Manual V1.0 16
3.4 Live View Page
The Live View page comes in several screen modes: 1920x1080, 1280x1024, 1280x720, 704x576,
704x480, 640x480 and 320x240. Users are allowed to select the most suitable one out of those
modes. Adjust the mode in accordance with your PC specifications and monitoring purposes.
1) General controls
Live View Page Setup Page Help Page
The video drop-down list allows you to select a customized or pre-programmed
video stream on the Live View page. Stream profiles are configured under
Setup > Basic Configuration > Video & Image. For more information, please
see “3.5.1 Basic Configuration > Video & Image” of User’s Manual.
The resolution drop-down list allows you to select the most suitable one
out of video resolutions to be displayed on Live View page.
The protocol drop-down list allows you to select which combination of
protocols and methods to use depending on your viewing requirements, and
on the properties of your network.
The preset drop-down list allows you to select the preset number for the PTZ
camera being used. This icon is inactivated if the PTZ settings are not set.
2) Control toolbar
The live viewer toolbar is available in the web browser page only. It displays the following
buttons:
The Stop button stops the video stream being played. Pressing the key again toggles the
start and stop. The Start button connects to the or starts playing a video stream.
The Pause button pauses the video stream being played.
The Snapshot button takes a snapshot of the current image. The location where the
image is saved can be specified.
The Digital Zoom button activates a zoom-in or zoom-out function for video image on the
live screen.
The Full Screen button causes the video image to fill the entire screen area. No other
windows will be visible. Press the 'Esc' button on the computer keyboard to cancel full
screen view.
The Manual Trigger button activates a pop-up window to manually start or stop the
event.
The PTZ button activates a pop-up window for Pan, Tilt and Zoom control.
Use this scale to control the volume of the speakers.

VK2-1080XVRDPTZ User Manual V1.0 17
Use this scale to control the volume of the microphone.
Use this scale to control the volume of the speakers and microphones.
3) Video Streams
The VK2-1080XVRDPTZ provides several images and video stream formats. Your
requirements and the properties of your network will determine the type you use.
The Live View page in the VK2-1080XVRDPTZ provides access to H.264 and Motion JPEG
video streams, and to the list of available video streams. Other applications and clients can
also access these video streams/images directly, without going via the Live View page.

VK2-1080XVRDPTZ User Manual V1.0 18
3.5 VK2-1080XVRDPTZ Setup
This section describes how to configure the network camera, and is intended for product.
Administrators, who have unrestricted access to all the Setup tools; and Operators, who have
access to the settings for Basic Configuration, Live View, Video & Image, Audio, Event, Dome
Configuration, System
You can configure the VK2-1080XVRDPTZ by clicking Setup in the top right-hand corner of the
Live View page. Click on this page to access the online help that explains the setup tools.
When accessing the VK2-1080XVRDPTZ for the first time, the “Admin Password” dialog appears.
Enter your admin name and password, set by the administrator.
NOTE: If the password is lost, the VK2-1080XVRDPTZmust be reset to the factory default settings.
Please see “Resetting to the Factory Default Settings”.
3.5.1 Basic Configuration
You can see the device information in this information page.

VK2-1080XVRDPTZ User Manual V1.0 19
1) Users
User access control is enabled by default. An administrator can set up other users, by giving
these user names and passwords. It is also possible to allow anonymous viewer login, which
means that anybody may access the Live View page, as described below:
The user list displays the authorized users and user groups (levels):
User Group
Authority
Guest
Provides the lowest level of access, which only allows access
to the Live View page.
Operator
An operator can view the Live View page, create and modify
events, and adjust certain other settings. Operators have no
access to System Options.
Administrator
An administrator has unrestricted access to the Setup tools
and can determine the registration of all other users.
Enable anonymous viewer login: Check the box to use the webcasting features. Refer to
“3.5.3 Video & Image” for more details.

VK2-1080XVRDPTZ User Manual V1.0 20
2) Network
The VK2-1080XVRDPTZ supports both IP version 4 and IP version 6. Both versions may be
enabled simultaneously, and at least one version must always be enabled. When using IPv4,
the IP address for the VK2-1080XVRDPTZ can be set automatically via DHCP, or a static IP
address can be set manually. If IPv6 is enabled, the VK2-1080XVRDPTZ an IP address
according to the configuration in the network router. There is also the option of using the
Internet Dynamic DNS Service. For more information on setting the network, please see “3.5.7
System > Network > Basic”.
Obtain IP address via DHCP: Dynamic Host Configuration Protocol (DHCP) is a protocol
that lets network administrators centrally manage and automate the assignment of IP
addresses on a network. DHCP is enabled by default. Although a DHCP server is mostly
used to set an IP address dynamically, it is also possible to use it to set a static, known IP
address for a particular MAC address.
Use the following IP address: To use a static IP address for the network camera, check
the radio button and then make the following settings:
- IP address: Specify a unique IP address for your network camera.
- Subnet mask: Specify the mask for the subnet the VK2-1080XVRDPTZ is located on.
- Default router: Specify the IP address of the default router (gateway) used for connecting
devices attached to different networks and network segments.
NOTES:
1. DHCP should only be enabled if using dynamic IP address notification, or if your DHCP
server can update a DNS server, which then allows you to access the VK2-1080XVRDPTZ
by name (host name). If DHCP is enabled and you cannot access the unit, you may have to
reset it to the factory default settings and then perform the installation again.
2. The ARP/Ping service is automatically disabled two minutes after the unit is started, or as
soon as an IP address is set.
3. Pinging the unit is still possible when this service is disabled.