VistaPure V3000 User manual

Installation Guide & Owner’s Manual
Specialized water filtration for autoclaves, dental bottles,
ultrasonic cleaners & instrument washers
Model V3000
106101
VistaResearchGroup.com
P.O. Box 321, Ashland, Ohio 44805-0321
From
City Water
To
Drain
To/From
Storage
Tank
Injection
Port
To
Wand
To
Faucet
Polishing Filter
R3255
VistaResearchGroup.com
Filter Installation Date
Replace this filter annually or as needed
based on local water quality.
Hyperfiltration Element
R3254 Replace whenever system-mounted
TDS meter “IN” displays number > 10%
of source water TDS.
VistaResearchGroup.com
Filter Installation Date
Deionization Filter
R3253 Replace this filter and R3252 when
system-mounted TDS meter “OUT”
displays number ≥ 4 ppm.
VistaResearchGroup.com
Filter Installation Date
Deionization Filter
R3252 Replace this filter and R3253 when
system-mounted TDS meter “OUT”
displays number ≥ 4 ppm.
VistaResearchGroup.com
Filter Installation Date
Prefilter
R3251 Replace this filter annually or as needed
based on local water quality.
VistaResearchGroup.com
Filter Installation Date

2Installation Guide & Owner’s Manual
TM
Table of Contents
Introduction ��������������������������������������������������������������������������������������������������������������������������������������������������������������������3
Important Information ��������������������������������������������������������������������������������������������������������������������������������������������������3
Preparation ����������������������������������������������������������������������������������������������������������������������������������������������������������������������4
System Overview ������������������������������������������������������������������������������������������������������������������������������������������������������������5
Installation �����������������������������������������������������������������������������������������������������������������������������������������������������������������������6
System Maintenance
Monitoring TDS �������������������������������������������������������������������������������������������������������������������������������������������������������10
Filter Life & Replacement Thresholds ����������������������������������������������������������������������������������������������������������������� 11
Changing Filter Elements �������������������������������������������������������������������������������������������������������������������������������������� 11
Checking Tank Air Pressure ����������������������������������������������������������������������������������������������������������������������������������12
Sanitizing the Tank and Faucet ����������������������������������������������������������������������������������������������������������������������������13
Filter Performance Record �����������������������������������������������������������������������������������������������������������������������������������14
VistaPure Limited Warranty ����������������������������������������������������������������������������������������������������������������������������������������15
VistaPure System Information �����������������������������������������������������������������������������������������������������������������������������������16
Pelton & Crane
Pelton�net
11727 Fruehauf Drive
Charlotte, NC 28273
United States of America
CUSTOMER SERVICE
[phone]
TECHNICAL SUPPORT
[phone]
Distribution
SciCan Inc.
SciCan�com
701 Technology Drive
Canonsburg, Pennsylvania 15317
United States of America
PHONE [phone]
FAX [phone]
TOLL FREE [phone]
SciCan Ltd.
SciCan�com
1440 Don Mills Road
Toronto, Ontario M3B 3P9
Canada
PHONE [phone]
FAX [phone]
TOLL FREE [phone]
VistaPure systems are sold through dental and medical dealers throughout North America by:
VistaPure is a trademark of Vista Research Group, LLC�
VistaResearchGroup.com vrg.support [phone]
 1244 County Road 1475, Ashland, Ohio 44805

3
© 2000-2018 Vista Research Group, LLC. All rights reserved.
VistaPure is designed to produce two grades of high-purity water: distilled-quality water for use in
autoclaves, and non-corrosive, low-TDS water for filling dental bottles, ultrasonic cleaners and for final
rinse cycles in instrument washers� Water used in autoclaves must be virtually free of dissolved solids
in order to protect the heating chamber and to prevent buildup of contaminants that can create hard
deposits and necessitate more frequent cleanings� Water used in self-contained dental bottle systems
should be of a high quality, but not distilled-grade water, which is corrosive to metals used in the
construction of dental units�
The VistaPure system is designed to be built in to sterilization center cabinetry, and can also be installed in
an equipment room� The system provides up to 4�25 gallons of treated water in its pressurized storage tank
(based on city water pressure), and automatically replenishes this supply as water is drawn from storage�
The system does not require electricity—it needs only a potable supply of cold water and a drain� To
maximize the life of the system filtration elements, we recommend that the water supplied to the system
be free of sediment, and softened if the source water is very hard�
Introduction
Please read this entire manual before proceeding with installation and operation, and always follow local
plumbing codes.
The VistaPure system can be installed nearly anywhere in the typical dental, medical, lab or hospital setting,
typically near a faucet and sink in a sterilization center� The system and tank are designed to fit in a base
cabinet, but can be installed anywhere there is a quality cold water supply and drain connection� The system
board is designed for horizontal installation� Please keep the system board and water storage tank at the same
level� The system should be installed no farther than 10-12’ from where the wand and faucet will be used�
Please locate the system label on the corner of the mounting board and record the installation date using a
fine-tipped permanent marker or some other writing instrument that will not smear�
IMPORTANT INFORMATION
For System Installers
We recommend that a professional technician or plumber familiar with dental/medical oces perform the
installation since interface with a cold water line and drain is involved� He/she should be familiar with local
plumbing codes and techniques for successful dental/medical equipment installations�
Please keep the Installation Guide & Owner’s Manual handy for future reference and ensure that anyone
responsible for operation and maintenance of the system is familiar with all details contained in this manual�
Please return the registration form or register online at vrg�support/register immediately upon installation�
IMPORTANT INFORMATION
For System Owners
We recommend turning o the system at the end of each work day by closing the valves on the system
board, water storage tank, and autoclave wand�

4Installation Guide & Owner’s Manual
TM
Preparation
Every VistaPure comes in two (2) cartons� Box 1 of 2 contains the system� Box 2 of 2 contains all other
items, including the Installation Guide & Owner’s Manual, warranty registration card, water storage tank,
dispensing wand, faucet, drain fitting, TDS meters, colored tubing and all other accessories� Make sure all
items needed for installation are present and undamaged� If damage is evident, contact the shipping
company or your distributor immediately�
Box 2
Box 1
VistaPure System
x2
x3
x2
S6112
1/4” Swivel Elbows
S6114
3/8” Swivel Elbows
S6119
3/8” x 3/8” x 1/4” Tee Union
S6133
3/8” Tube x Faucet
S6135
3/8” Angle Stop Adapter
x 3/8” Compression x 1/4” Tube
S6161
3/8” x 1/4” Tank Valve
S6310
3/8” x 1/4” Union
S6588
Cable Ties
S6589
Mounting Cable Tie
S9035
Syringe
S9111
Water Storage Tank
S9117
Economy TDS Meter
S9155
VistaPure Chrome Faucet
S9300
VistaPure Wand
(with clip, wrench, screws)
DH154
DrainHub (four-port)
S4730
1/2” NPT x 1/4” Tubing
Male Adapter
S8015
1/2” NPT Plug
Tubing
White (3/8”)
Natural (3/8”)
Red (1/4”)
Blue (1/4”)
Black (1/4”)
Blue Coil (3/8”)
12’
12’
12’
12’
12’
x3
10’

5
© 2000-2018 Vista Research Group, LLC. All rights reserved.
System Overview
VistaResearchGroup.com
P.O. Box 321, Ashland, Ohio 44805-0321
From
City Water
To
Drain
To/From
Storage
Tank
Injection
Port
To
Wand
To
Faucet
106101
From
City Water
To
Drain
To/From
Storage
Tank
Injection
Port
To
Wand
To
Faucet
From
City Water
To
Drain
To/From
Storage
Tank
Injection
Port
To
Wand
To
Faucet
H
F
D
D
G
B
C
E
A
To Drain
To Tank
To Wand
To Faucet
From H20 Supply
R3253
Deionization Filter
R3252
Deionization Filter
R3251
Prefilter
R3254
Hyperfiltration Element
R3255
Polishing Filter
K
J
M
N
I
System Manifold
A1 From City Water to Prefilter
A2 To Drain from Pump
A3 To and from Storage Tank
A4 Injection Port to Tank Line
A5 To Autoclave Wand
A6 To Bottle Faucet
AAutomatic Shut-O Valve
System Water Shut-O Valve
Check Valves
Injection Port Assembly
Flow Restrictor
Permeate Pump
Dual TDS Meter
B
C
D
E
F
G
H
DrainHub with fittings
Storage Tank Shut-O Valve
Water Storage Tank
Tank Air Valve
VistaPure Wand
VistaPure Chrome Faucet
I
J
K
L
M
L
N

6Installation Guide & Owner’s Manual
TM
Installation
If the system is not already mounted in another product (sterilization center, etc�), mount as desired near a cold
water source and drain�
Provide for a 1/4” connection to the cold water supply� This is usually accomplished using a compression fitting
or one of the supplied fittings on the cold water line� Check local codes�
1
2
2A 2B S6119
3/8” x 3/8” x 1/4” Tee Union
For 3/8” O�D� smooth
supply tubing
S6135
3/8” Angle Stop Adapter
x 3/8” Compression x 1/4” Tube
For 3/8” braided supply lines
with prefitted compression nuts
2A
2B
NOTE:
Use either 4A or 4B method to
supply cold water to the VistaPure�
Where can it be installed?
The VistaPure system and included tank are designed to fit in a
base cabinet, but can be installed anywhere there is a quality cold
water supply and drain connection.
The system board is designed for horizontal installation—typically
on the right side of the inside of a base cabinet—and can be
“flipped” to be installed horizontally on the opposite side, if
necessary. Ideally, the system board and water storage tank
should be installed at the same level, and located no farther than
10-12’ from where the wand and faucet will be used.

7
© 2000-2018 Vista Research Group, LLC. All rights reserved.
Provide a drain connection with trap as shown below� A four-port DrainHub (DH154) and adapter fittings
are included with each VistaPure system� This CSA-certified, multi-port drain adapter makes it simple and
convenient to add drain connections in the future, if needed� Be sure to install a 1/2” NPT threaded plug
(provided) in any unused port(s) of the DrainHub�
3
4
1-1/2”
w/ Trap Drain Line
from VistaPure
3C
Drain Line
from VistaPure
1-1/2”
w/ Trap
3D
3A
Drain Line from
Instrument Washer
Drain Line
from VistaPure
To Branch
Tailpiece
Countertop
Airgap above
Flood Rim
3E
3A Typical installation of DrainHub (DH154) using existing sink drain system� Push-to-connect adapter (S4730)
and three 1/2” NPT plugs (S8015) are included with the VistaPure system� Various optional configurations are
available�
Installation beside the main drain line can oer maximum flexibility and minimize any sounds of drainage
possibly noticeable from the sink drain� This optional position can be achieved with the use of a simple drain tee
adapter fitting�
Alternate installation of drain Air Gap (S9145) using existing sink drain system� Order separately�
Alternate installation of drain Air Gap (S9145) using separate riser and trap� Order separately�
Alternate installation of dual inlet drain Air Gap system (S9147) using branch tailpiece� Order separately�
Mount the faucet on the sink or countertop deck in the sterilization center, lab or kitchenette as desired� The
faucet & 3/8” push-type faucet connector fitting are included in the accessory kit� If it is necessary to drill a hole
through the countertop surface, the hole needs to be 5/8” (or 1�5cm) wide�
3C
3D
3E
NOTE:
Local codes vary greatly, so be sure to verify the preferred method prior to installation. Every VistaPure has a pressurized drain discharge and
multiple check valves in the system to prevent backflow from drain connections.
If additional backflow measures are required, a 1/4” VistaCheck Dual Check Backflow Preventer (VC250-A) can be installed on the red water
supply line. VistaCheck is CSA-certified for supply lines in the USA and Canada.
3B
3B

8Installation Guide & Owner’s Manual
TM
• If the system is mounted inside a cabinet, under a sink or on a sliding device, be careful that tubes are
not crushed or crimped� If the system is on a sliding device for easy access, make certain to create a coil
with the tubes that will allow the system to move in and out without causing damage or restriction�
• If the VistaPure system is to be installed remote to the autoclave(s) and/or in a cabinet, fish the solid
blue tubing behind cabinetry to the autoclave center� Join the solid blue tubing and the coiled blue
tubing with the white 1/4” x 3/8” push-type union that is already attached to one end of the coiled
tubing� Make certain to provide a restraint at the straight end of the coiled tubing near the union so that
when pulling out on the autoclave wand and coiled tubing the union connection is not stressed� Extra
lengths of tubing are included with each system� A mounting zip tie is provided with system�
RED From Cold Water Supply NATURAL To and From Tank BLUE STRAIGHT To Autoclave Area
BLACK To Drain WHITE To Faucet BLUE COILED To Autoclave Filler Wand
Attach colored tubing to the proper segments on the system manifold and the appliance/device as
shown below and on page 5� When attaching tubing to the push-type fittings, make certain all tubing
cuts are straight and free from burrs� Tubing must be firmly inserted into the fitting (11/16” plunge) to
avoid leaks�
5
6Wand Installation
6A
6B
6C
USE: To use the wand, remove it from the clip holder, turn the blue valve handle so it’s inline with the
tubing, then press downward on the mushroom button� Water will flow from the spout�
STORAGE: To store the wand after use, turn the blue handle so it is 90º to the tubing and press the wand
into the clip holder�
Push wand assembly valve onto the end of the 3/8” O�D� coiled tubing� Firmly push and twist the
tubing to make certain it engages into the O-ring in the valve�
Attach the white 3/8” x 1/4” union adapter on the opposite end of the coiled tubing to the 1/4”
tubing that runs to the “Autoclave Wand” port on the VistaPure system manifold� Secure the
union adapter to a solid surface using the included mounting zip tie�
Attach the small wand holder clip to the desired location using the two screws provided� The
clip may be oriented in any direction and mounted in any location�

9
© 2000-2018 Vista Research Group, LLC. All rights reserved.
Position the water storage tank as near to the VistaPure system board as possible, at the same level�
The system board and storage tank can be separated by up to 30 feet (9 meters), as long as they’re
on the same level and there are no significant “dips” in the tank line tubing, which could create back
pressure�
Locate the white elbow tank valve in the accessory pack and attach valve to the top of the storage
tank� Hand-tighten only—never use tools on system valves and fittings! Make sure to open the tank
valve after installing it on the tank—the system will not work if the tank valve is closed� (A valve handle
in the open position is in line with the tubing; when closed, it is 90° to the tubing�)
Check the air pressure pre-charge in the water storage tank according to the maintenance
instructions on page 12�
After all tubing connections have been made, turn the cold water supply valve on to allow water to
enter the system� Allow it to run for at least 10 minutes� Wastewater should run to the drain and a
pulsing/ clicking sound should be audible from the permeate pump—this is normal� Check for leaks at
all connections�
Sanitize the storage tank and faucet following the maintenance instructions on page 13�
After installing the system, checking the air pressure in the storage tank, and sanitizing the tank and
faucet, the VistaPure system is ready for use� Depending on the city water pressure, filling the storage
tank completely (up to 4�25 gallons for the standard tank) may require about an hour� However, water
can be used any time after about 30 minutes, as the system can send water to the wand and faucet
even while making new water�
7
9
11
8
10
12

10 Installation Guide & Owner’s Manual
TM
Total dissolved solids (TDS) is the quantitative measure of virtually all constituents found in a particular
water supply, counted as parts per million (ppm) or milligrams per liter (mg/L)� Water is simply H2O;
basically, everything else found in it would contribute to the TDS� A typical city water supply will have a TDS
reading of 150-350 ppm, although it varies greatly�
Water for use in autoclaves should be of distilled quality, which is a TDS of 0-5 ppm (0-4 ppm preferred)�
Water with TDS readings higher than 5 ppm will eventually cause scale build-up and more frequent
cleaning and/or repair� The worse the water, the more costly the maintenance and repairs—to the point
that some autoclaves won’t even operate if the TDS is high�
The VistaPure system comes equipped with a battery-operated dual TDS meter that enables you to check
the water quality throughout the system� For example, slide the switch on the TDS meter (see Figure F) to
“IN�” This reads the level of TDS in the water emerging from the Hyperfiltration element� Slide the switch to
“OUT” to display the level of TDS emerging from the Deionization filters�
A separate, handheld TDS meter is also included, which can be used to determine the level of TDS in the
supply water fed to the system� With these data, one can monitor the complete process as necessary�
Under normal operating conditions, TDS levels might be as follows in this example:
City Water Feed = 200 ppm TDS = X
After Hyperfiltration = 010 ppm TDS = 5% of X
After Deionization = 000 ppm TDS
Remember, this is only an example� However, the reading on the “IN”
should generally be about 5% or less of the inbound water TDS� The
Deionization filters remove the balance remaining to achieve the 0-4
ppm TDS level desired�
Figure E shows the handheld TDS monitor provided with your system�
It can be used to determine the quality of the raw and treated water�
Simply remove remove the protective cap exposing the probe, push the
power button to activate, and immerse the probe into the water� The
LCD display will show the TDS level� After use, shake the water out of
the probe area and wipe the outer portion dry—never push anything
into the probe area� Check the water quality frequently and change
filter elements as required� Both TDS monitors are powered by a simple
button-cell battery, available at most any store�
Monitoring TDS
NOTE:
Replacement batteries for meters should be purchased locally� Both
included TDS meters take two (2) of the following battery:
357A (LR44) Alkaline Button Cell - 1�5V 110mAh�
Water should be running through the system when checking water quality using the system-mounted
TDS meter. Simply run the VistaPure faucet for a few moments and the system will start to produce
water and yield accurate results.
Check TDS levels at least monthly and record the data in the chart on page 14.
F
E

11
© 2000-2018 Vista Research Group, LLC. All rights reserved.
Changing Filter Elements
Warning: never attempt to change any filter element(s) with pressure on the system�
Follow these steps when changing filter elements:
Turn OFF water inlet supply (Figure C on page 5)�
To relieve all pressure from the system, discharge all water from the storage tank by locking open the
handle on the chrome faucet (lift UP on the black handle)
Disconnect the tubing from any filter element(s) to be replaced by pushing in on the collet and
removing the tubing, starting on the side of the filter(s) opposite the system manifold�
Pull the filter(s) out away from the board, one clip at a time, then disconnect the tubing from the other
end of the filter(s)�
Reverse the process to install your replacement filter(s)� Take care to note the proper direction of flow�
Don’t forget to record the installation date on the filer label using a permanent marker and in the table
on the back panel of the instruction manual�
After any filter elements are replaced, perform a system cleansing procedure as outlined on page 13�
This cleansing procedure should be followed at least once per year and anytime a filter is changed�
1
2
3
4
5
6
Notice: During the initial installation and at least once per year during the tank cleansing process, check
the air precharge pressure in the water storage tank using a digital tire pressure gauge� With the tank empty
and water valve in the OPEN position, remove the cover cap from the air valve and check the precharge air
pressure� The precharge pressure should be set at 6�0-7.5 psi for most applications� Add air as needed using
a tire pump or compressor� To lower air pressure if too high, depress the stem in the air valve and re-check�
See complete directions on page 12�
Filter Life & Replacement Thresholds
Prefilter (R3251): approximately one year (change at least annually)�
Deionization Filters (R3252 & R3253): 4 months to 3 years, depending on volume of usage and quality
of local water supply� Change BOTH deionization filters whenever the system-mounted TDS meter “OUT”
(recorded in Column D above) displays a number equal to or greater than 4 parts per million (ppm)�
Hyperfiltration Element (R3254): 3-5 years, depending on the volume of usage and quality of local water
supply� Replace the hyperfiltration filter whenever the system-mounted TDS meter “IN” exceeds 10% of the
TDS of the municipal water supply TO the system, as measured with the included, handheld meter (percent
recorded in Column C above)�
Polishing Filter (R3255): approximately one year (change at least annually)�

12 Installation Guide & Owner’s Manual
TM
Checking Tank Air Pressure
At least once per year and whenever filters are changed, check the air pressure of the system’s water
storage tank�
Things you’ll need:
• Digital tire air pressure gauge (available for less than $10 at most auto supply retailers)
Note: If air ever comes out of the tank valve or water comes out of the air valve, the diaphragm in the tank is
damaged and the tank needs to be replaced� See the support section available online at http://vrg�support�
Turn o the main water supply to the
system�
Lock the chrome bottle faucet open to drain
the tank completely�
When the water stops flowing, locate
the small cap on the air valve� Turn it
counterclockwise to remove the cap�
Use the digital tire gauge to check the air
pressure pre-charge� The air pressure should
be a minimum of 6�0 psi (41 kPa) and a
maximum of 7�5 psi (52 kPa)�
To add air to the tank, use a compressor or
bicycle tire pump� To remove air, press in
gently on the valve needle� Use the air gauge
to check for desired pressure�
When finished checking air pressure, thread
the cap back onto the air valve, close the
faucet and sanitize the tank and faucet line�
See instructions on page 13�
1
2
3
4
5
6

13
© 2000-2018 Vista Research Group, LLC. All rights reserved.
Turn o the main water supply to the
system�
Lock the chrome bottle faucet open to drain
the tank completely, then close the faucet�
Place one ounce (30 mL/cc) of 8�25%
unscented chlorine bleach into a small cup�
Dip one end of a clean cotton swab into the
bleach, then carefully wipe the tip and inside
edge of the faucet opening�
Remove the cap from the tube on the
injection port of the system manifold�
Draw the chlorine bleach into the 35 cc
syringe provided with the system and inject
the bleach into the injection port tube�
Draw a full syringe of plain water, then inject
the water into the injection port tube and
replace the cap�
Turn on the water supply to the system and
allow it to make water for 10 minutes�
Open the chrome faucet until water
emerges for a few seconds and bleach can
be detected, then turn o the faucet�
Let the system sit idle for another
20 minutes�
Open the chrome bottle faucet and allow
the water to run until all water has been
drained from the tank�
To rinse the tank, waterlines and faucet,
close the faucet and allow the system to
make water for at least 10 minutes�
Open the chrome bottle faucet and allow
the water to run until all water has been
drained from the tank� Make sure that the
water running from the faucet no longer has
a noticeable bleach odor�
Close the faucet and allow the system to
make water and refill the tank completely�
The system is now ready for use�
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Sanitizing the Tank and Faucet
At least once per year and whenever filters are changed, sanitize the VistaPure system. This process
requires about one hour before the system is ready for use again�
Things you’ll need:
• One ounce (30 mL) of non-scented chlorine bleach
• 35 cc (mL) syringe (included with each VistaPure system)
• Clean cotton swab

14 Installation Guide & Owner’s Manual
TM
Date
“A”
City Water to System
(Use Handheld
TDS Meter)
“B”
After Hyperfiltration
(Use Mounted
Meter “IN”)
“C”
% TDS Remaining
(Divide Column B
by Column A)
“D”
TDS after D/I
(Use Mounted
Meter “OUT”)
“E”
Water from Wand
(Use Handheld
TDS Meter)
“F”
Water from Faucet
(Use Handheld
TDS Meter)
Filter Performance Record

15
© 2000-2018 Vista Research Group, LLC. All rights reserved.
During the time period and subject to the conditions
hereinafter set forth, Vista Research Group, LLC
(VRG) will repair or replace to the original user any
portion of a VistaPure which proves defective due
to defective materials or workmanship of VRG�
Contact your nearest authorized VRG distributor/
dealer for warranty service� At all times VRG shall have
and possess the sole right and option to determine
whether to repair or replace defective equipment,
parts, or components� Damage due to conditions
beyond the control of VRG is NOT COVERED BY THIS
WARRANTY� (Contact parcel or freight company for
claims on freight damaged in transit)
WARRANTY PERIOD: VRG shall warrant its VistaPure
systems for a period of one (1) year from the date of
installation, or eighteen (18) months from the date of
manufacture, whichever comes first�
LABOR, ETC., COSTS: VRG shall IN NO EVENT be
responsible or liable for the cost of field labor or other
charges incurred by any customer in removing and/
or re-axing any VRG product, part or component
thereof�
THIS WARRANTY WILL NOT APPLY: (a) To defects
or malfunctions resulting from failure to properly
install, operate or maintain the unit in accordance
with printed instructions provided; (b) to failures
resulting from abuse, accident or negligence; (c)
to normal maintenance services and the parts used
in connection with such service; (d) to units which
are not installed in accordance with applicable local
codes, ordinances and good trade practices; (e) if the
unit is moved from its original installation location, or;
(f) if the unit is used for purposes other than for what
it was designed and manufactured�
RETURN OF REPLACED COMPONENTS: Any item to
be replaced under this Warranty must be returned to
Vista Research Group, LLC (VRG) in Ashland, Ohio,
or such other place as VRG may designate, freight
prepaid� Write to the address listed below for a return
authorization and the physical address to which items
should be returned for warranty attention�
PRODUCT IMPROVEMENTS: VRG reserves the right
to change or improve its products or any portions
thereof without being obliged to provide such change
or improvement of units sold and/or shipped prior to
such change or improvement�
WARRANTY EXCLUSIONS: As to any specific VRG
product, after the expiration of the time period of
the warranty applicable thereto as set forth under
the heading “Warranty Period” above, THERE WILL
BE NO WARRANTIES, INCLUDING ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR ANY PARTICULAR PURPOSE.
Some states do not allow limitations on how long an
implied warranty lasts, so the above limitations may
not apply to you� No warranties or representations at
any time made by any representative of VRG shall vary
or expand the provisions hereof�
LIABILITY LIMITATION: IN NO EVENT SHALL VRG
BE LIABLE OR RESPONSIBLE FOR CONSEQUENTIAL,
INCIDENTAL OR SPECIAL DAMAGES RESULTING
FROM OR RELATED IN ANY MANNER TO ANY VRG
PRODUCT OR PARTS THEREOF.
Some states do not allow the exclusion of limitation
of incidental or consequential damages, so the above
limitation or exclusion may not apply to you�
This Warranty gives you specific legal rights and you
may also have other rights which vary from state to
state�
For your warranty protection (Magnason-Moss
Warranty Act), the warranty card, if provided, should
be completed and returned to VRG within ten (10)
days of installation� Alternatively, register your product
online within ten (10) days of installation at
vrg.support/register� In the absence or other suitable
proof of installation date, the eective date of this
warranty will be based upon the date of manufacture
plus one hundred eighty (180) days�
VistaPure Limited Warranty

VistaPure Specialized water filtration for autoclaves,
dental bottles, ultrasonic cleaners & instrument washers
System Model # V3000
System Serial #
Installer Name
Installer Phone
Install Date
Dealer
Dealer Phone
Dealer Address
Notes
VistaPure System Information
Thank you for purchasing the VistaPure system for your practice! The following chart is for necessary
information for future reference� Please fill this out completely and keep this manual in a convenient place
for ready access and reference�
Be sure to use our convenient online warranty registration form at vrg.support/register� If you’d prefer,
you may complete and return the included Warranty Registration sheet� Make a copy of the form for your
records, then mail the original to us�
Operating Temperature Range 45º - 100º F
Operating Pressure Range 40 - 100 psi
Optimal pH Range 6�5 - 8�5
Max Total Dissolved Solids (TDS) 500
Max pH Range 5�5 - 9�5
Max Influent Hardness 10 gr / 171 ppm
Max Influent Manganese 0�05 ppm
Max Influent Iron 0�1 ppm
Max Influent Hydrogen Sulfide None
Max Influent Chlorine / Chloramine 2 ppm
Max Daily Output (24 hours) 100 Gal (378 L)
Prefilter Element Service Life 1 Year Max
Prefilter Replacement Order # R3251
Deionization Filter Elements Service Lives 4-18 Months
Deionization Filter Replacement Order #s R3252 & R3253
Hyperfiltration Filter Element Service Life 3-5 Years
Hyperfiltration Replacement Order # R3254
Polishing Filter Element Service Life 1 Year Max
Polishing Filter Replacement Order # R3255
System Dimensions (W x H x D) 22” x 16” x 6�5”
Tank Dimensions (Dia x H) 12” x 18�25”
Approximate Ship Weight (Dry 2 Cartons) 42 lbs
TM
V3000IGOM180402
VistaResearchGroup.com vrg.support [phone]
 1244 County Road 1475, Ashland, Ohio 44805