Visture T05N User manual

Smart TPMS
Installation Guide
Internal Sensor

Smart Tire Pr essure Mo nitorin g System
Instal lat ion Guide o f interna l sensor
Smart Tire Pr essure Mo nitorin g System
Instal lat ion Guide o f interna l sensor
1, Installation of internal sensor
A,Components of internal sensor
Sensor
Sensor module
Non-slip nuts
Position tag
EPDM seal Aluminum tube
Fixing nut
Cap
Pad
Wheel sticker
B,Installed sensor corresponding to tires' position
ID code of four sensors are configured.
You only need to install sensors correspond to tire position.
Installation position shown below:
F.L
R.L
F.R
R.R
Please install sensor per sensor's position tag

Smart Tire Pr essure Mo nitorin g System
Instal lat ion Guide o f interna l sensor
Smart Tire Pr essure Mo nitorin g System
Instal lat ion Guide o f interna l sensor
C,Internal sensor installation
Please install configured receiver and sensors.
If there is wrong ID code or mix position of sensor,
please refer “learn code by inflate&deflate”
(detail please refer to use manual of receiver)
Please make sure receiver is open when installing sensor,
in this way, data could be sent to receiver immediately once sensor installed.
Detail process:
2,Picture of installation sensors
1,Remove the tire from vehicle, detached tire and rim, then clean inside of tire and rim.
2,Select internal sensor ,which is assembled ( sensor + valve) in advance, of corresponding tire's position
3,Install internal sensor accompanied with valve, make sure there is gap between sensor module and wheel.
Instead original valve with internal sensor, then put pad around valve and fasten fixing nut . shake the valve
gently up and down to make sure sensor closed to wheel finally screw fixing nut by tool.
(install sensor with plastic valve is same as install normal valve, just using tool to pull out valve. Please pay
attention there is distance between sensor module and wheel)
4,Inflate tire after installed sensor, and check leakage by using foam, ensure no leakage
5,Adjust lead weight and do balance of wheel
6,Installation other sensors by same method
Jack up car, remove tire Detach tire and rim Cut off the original valve
(do not scratch wheel)
Insert sensor Pull out of the valve with
specia l tool s(on ly for plastic valve)
Ensure gas noz zle is c lose t o rim, and
mount pad, fas teni ng nut o ne by one
( only for a lumi num va lve)
Inflate to standard pressure
af ter i nstalled Adjust the lead weight Do balance
F
F.L
D
F.L
E

Smart Tire Pr essure Mo nitorin g System
Instal lat ion Guide o f interna l sensor
Smart Tire Pr essure Mo nitorin g System
Instal lat ion Guide o f interna l sensor
Batter y life
Working voltage
Storage temperature
Working temperature
Temperature accuracy
Working pressure
Pressure accuracy
Transmit power
Dimension
Transmit frequency
IP
Weight
Warranty is 1 year counted from buying date ( not include periodically consumable part ).
Exception to warranty:
1,Don't follow user manual to operate product
2,Product damaged because of accident,neglect,abuse,misuse
3,Repair without authorization.
4,Damaged due to transportation
5,Ther damage not because of design,technical,manufacturing and quality problem
All failure products should be sent to us or our authorized repair center, attached with detail
Please find warranty card in specification of receiver.
if the product failure under normal operation, We will provide free replacement or repair
during the period of warranty. We reserves the right to change new products or other
equivalent product.
description of defect and show original purchase invoice. Warranty card is effective only in
purchased country. This warranty is restricted to above conditions, we will not responsible for
the damage related to our products (like tire explosion). This warranty provides you specific
legal rights, but may also varied different rights for other countries.
4,Warranty
3,Parameter of internal sensor
>5ye ar s
2.1V-3.6V
0-99Psi
±1.5Psi
IP67
<10dBm
433.92 MHz
70mm*53mm*20mm
≤ 30g(weight exclude valve 16g)