Vitek Transcendent Series User manual

VITEK
VTC-THT2RFE-2
VTD-THD2RFE-2
VTC-THB2RFE-2
FEATURES
• 1/2.9” 2.1 MegaPixel Progressive Scan CMOS Image Sensor
• High Definition Analog (HDA) / HD-TVI / AHD / HD-CVI / CVBS
• 2.8mm Fixed Iris Lens
• Supports OSD Menu
• 1 Matrix IR with up to 100’ IR Range (VTC-THB2RFE-2,
VTC-THT2RFE-2)
• 16 IR LEDs with up to 65’ Range (VTD-THD2RFE-2)
• True Mechanical Day/Night function by ICR
• Digital Wide Dynamic Range (D-WDR)
• XD-DNR Noise Reduction
• Supports Up The COAX Control (CoC)
• IP67 Weather Resistance (+IK10 on VTD-THD2RFE-2)
• Over 1500’ HD Video Transmission (Depending on cable
characteristics and integrity)
• VTC-THB2RFE-2: Optional J Boxes VT-TJB07, TJB08
• VTC-THT2RFE-2: Optional J Boxes VT-TJB01, TJB08,
Wall Mount VT-TWMT-3
• VTD-THD2RFE-2: Optional J Box VT-TJB03A, Wall Mount
VT-TWMT-3, In-ceiling Semi Flush Mount VT-TFMT-S
• 12VDC Operation
• 3-year Warranty
Transcendent Series 2.1 Megapixel Indoor/Outdoor
HD-TVI/AHD/CVI/CVBS IR Cameras

2
Safety Precaution
CAUTION: TO REDUCE THE RISK OF ELECTICAL
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
To prevent electrical shock and risk of fire hazards, do not expose this unit
to rain or moisture and only use specified power source..
Warning :
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
their own expense.
Caution :
Any changes or modifications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user's authority
to operate the equipment.
Main power quality should be that of atypical commercial environment. If the user
of the model requires continued operation during power interruptions, it is
recommended that the device be powered from an uninterruptible power supply
(UPS).
The symbol is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature
accompanying the unit.
The symbol is intended to alert the user tothe presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude toconstitute a risk of electrical shock.

3
VTC-THB2RFE-2 Components
Overview
Screws
Drill Template
Camera
User Manual
34
1
2
57
6
Video Connection
Connect the BNC video connector to a BNC cable, then to a DVR.
Power
12VDC
Power Connection
Connect the power connector to a regulated 12 VDC power adaptor.
Monitor
Video
Lens
Sun Shield
Mount Lock
Mount Base
BNC Video Output
Output Mode Switch
Power Cable
1
2
3
4
5
6
7
This series supports AHD/TVI/CVI/CVBS video output.
The video output can be changed by pressing and holding the button in the
video switch cable for 5 seconds (the default video output is TVI video
output). Before switching video outputs, please remove the cover of the
video switch cable.
Video Output Mode Switch:

4
Installation
Before you begin, please make sure that the wall or ceiling is strong
enough to withstand 3 times the weight of the camera. The mounting
steps are as follows:
2. Route the cables and connect the power & video cables, use the
rubber plug to fill the gap of the mounting base. then secure the
mounting base to the ceiling or wall with screws.
3. Loosen the mount lock to adjust the Pan and Tilt of the camera, then
tighten the mount lock to secure the viewing angle adjustments.
1. Attach the drill template to
the place where you want to
install the camera, then drill
3 screw holes and 1 cable
hole (if you want to route the
cables through the mounting
base) according to the drill
template

5
VTC-THT2RFE-2 Components
Overview
2
1
3
4
Camera
Manual
Screws
Hex Wrench
Mounting Plate
Rubber Plug
Lens
Lock Screws
BNC Video Output
Output Mode Switch
Power Cable
1
2
3
4
5
5
Monitor
Video
Video Connection
Connect the BNC video connector to a BNC cable, then to a DVR.
Power Connection
Connect the power connector to a regulated 12 VDC power adaptor.
Power
12VDC
This series supports AHD/TVI/CVI/CVBS video output.
The video output can be changed by pressing and holding the button in the
video switch cable for 5 seconds (the default video output is TVI video
output). Before switching video outputs, please remove the cover of the
video switch cable.
Video Output Mode Switch:

6
Installation
Before you begin, please make sure that the wall or ceiling is strong
enough to withstand 3 times the weight of the camera. The mounting
steps are as follows:
1. Attach the drill template to
the place where you want to
install the camera, then drill
3 screw holes and 1 cable
hole (if you want to route the
cables through the mounting
base) according to the drill
template
.
2. Route the cables and
connect the power & video
cables, then secure the
mounting base to the ceiling
or wall with screws.
3. Loosen the lock screws, then
adjust the camera to obtain
the optimium viewing angle.
Confirm the correct viewing
angle with a monitor. Next
insert the rubber plug.
4. Tighten the lock screws to secure the viewing angle adjustments.
Rubber Plug

7
VTD-THD2FE-2 Components
Overview
Camera
Manual
Drill Template
Screws
Hex Wrench
Mounting Base
Dome Cover
BNC Video Output
Output Mode Switch
Power Cable
1
2
3
4
5
1
2
3
4
5
Monitor
Video
Video Connection
Connect the BNC video connector to a BNC cable, then to a DVR.
Power Connection
Connect the power connector to a regulated 12 VDC power adaptor.
Power
12VDC
This series supports AHD/TVI/CVI/CVBS video output.
The video output can be changed by holding and pressing the button in the
video switch cable for 5 seconds (the default video output is AHD video
output). Before switching video outputs, please remove the cover of the
video switch cable.
Video Output Mode Switch:

88
4. Adjust the Three-axis camer bracket to obtain the optimium
viewing angle.
5. Install the dome bubble on
the camera with the screws,
then carefully remove the
protective film to complete
the installation.
Installation
Before beginning installation, make sure that the wall or ceiling is
strong enough to withstand 3 times the weight of the camera. The
mounting steps are as follows:
2. Loosen the screws to open
the lower dome and then
loosen the lock screw to
remove the mounting base.
1. Attach the drill template to
the place where you want to
install the camera, then drill
the screw holes and 1 cable
hole according to the drill
template.
3. Route the cables and
connect the power & video
cables, use the rubber plug
to fill the gap of the mounting
base. then secure the
mounting base to the ceiling
or wall with screws.
Rubber Plug
Pan: 0°~240°
Rotation: 0°~220° Tilt: 0°~68°

9
Camera OSD Menu
The Transcendent 4-in1 camera series must be connected to a DVR
which supports HD-TVI/AHD video signal input and COC protocol to
access the OSD setup menu. Different DVRs manufacturers may have
different modes of menu operation.
You can select the menu by clicking (U) or (D) key on the
direction area. Click (L) or (R) key to select the menu on the
left. The menu with arrow icon which means it has sub-menu. You
can select the menu and click the Enter Button to enter the
sub-menu. to return to previous screen, arrow down to Return and
click Enter Button. To Exit menu arrow down to Exit and click Enter
Button.
You will see the following interface by clicking the PTZ button.
The Following image will pop-up when you left click once on the
image when using Transcendent HDA DVR's.
Click on the OSD tab and then click on the camera menu
button.

10
Detailed Specifications VTC-THT2RFE-2 VTC-THB2RFE-2
Image Sensor
Signal System
Effective Pixels
Resolution
Video Output
Lens
Day/Night
Min. IIIumination
IR LEDs
IR Distance
S/N Ratio
WDR
Digital Noise Reduction (DNR)
White Balance
BLC
Up the COAX Control (COC)
Transmission Distance
Power Input
Power Consumption (12VDC)
Resistance Rating
Operation Conditions
Weight
Dimensions
1/2.9” 2.1 Megapixel Progressive Scan CMOS Sensor
PAL/NTSC
1920(H) x 1080(V)
HD-TVI / HD-CVI / AHD: 1080p/720p (2.1 MegaPixel) / CVBS: 960H
HD-TVI / AHD / CVI / CVBS (Selectable)
2.8mm - Fixed
True Day/Night by ICR
0 lux (with IR ON)
Up to 100’
≥52dB (AGC Off)
XD-DNR (3D-DNR / 2D-DNR)
Auto (AWB)
YES
YES
Up to 1500’ (Depending on cable characteristics & integrity)
12VDC
IP67
-4°~122° / 10%~90% Humidity
6.6 x 2.93” (167.5 x 74.5mm)
1 Matrix
Ф4.25 x 3.75” (Ф108 x 95.7mm)
Digital WDR
VTD-THD2RFE-2
Ф4.57 x 3.58” (116×91mm)
+IK10
Day : < 1W; Night : < 3W
13.01 oz. / 0.82 lbs. / 370g
14.11 oz. / .88 lbs. / 400g 20.46 oz. / 1.28 lbs. / 580g
Up to 100’
1 Matrix 16 IR LEDs
Up to 65’

11
OPTIONAL MOUNTS FOR FIXED TRANSCENDENT CAMERAS
VT-TJB01
Optional Junction
Box for Cable
Management
for use with Select
Transcendent Bullet
and Turret Style
Cameras including
VTC-THT2RFE-2.
VT-TWMT3
Optional Wall Mount
for use with Select
Transcendent Fixed
Lens Turrets and Domes.
VT-TJB08
Optional Junction
Box for Cable
Management for
use with Select
Transcendent
Cameras including
VTC-THT2RFE-2, VTC-THB2RF2.
VT-TJB07
Optional Junction
Box for Cable Management
for use with Select Bullet
Style Cameras including
VTC-THB2RFE-2.
VT-TJB03A
Optional Junction
Box for Cable
Management for
use with Select
Transcendent Vandal
Dome Cameras
VT-TFM-S
Optional In-Ceiling
Semi-Flush Mount for
use with Fixed
Lens Vandal Dome
Cameras

Limited Product Warranty
VITEK products carry a three (3) year limited warranty. VITEK warrants to
the purchaser that products manufactured by VITEK are free of any rightful
claim of infringement or the like, and when used in the manner intended,
will be free of defects in materials and workmanship for a period of three
(3) years, or as otherwise stated above, from the date of purchase by the
end user. This warranty is nontransferable and extends only to the original
buyer or end user customer of a VITEK Authorized Reseller.
The product must have been used only for its intended purpose, and not
been subjected to damage by misuse, willful or accidental damage, caused
by excessive voltage or lightning.
The product must not have been tampered with in any way or the
guarantee will be considered null and void.
This guarantee does not affect your statutory rights.
Contact your local VITEK Reseller should servicing become necessary.
VITEK makes no warranty or guarantee whatsoever with respect to
products sold or purchased through unauthorized sales channels. Warranty
support is available only if product is purchased through a VITEK
Authorized Reseller.
28492 CONSTELLATION ROAD VALENCIA, CA 91355
WWW.VITEKCCTV.COM
Version 1.0
April 2020