Vitek VTC-C770DN User manual

BLACKYELLOWMAGENTACYAN
VITEK
VTC-C770DN
700TVL True Day and Night
(ICR) Camera
• 1/3” Sony High Density EXVIEW CCD
• Sony Effio Digital Signal Processor
• 700TVL High Resolution
• .003Lux (F1.2@50IRE)
• Supports C/CS mount DC drive lenses
• Supports NTSC & PAL Standards
• Adaptive Tone Reproduction
• 2DNR - Two Dimensional Motion Adaptive Noise Reduction
• Motion Detection
• Privacy Mask
• On Screen Display (OSD) Menu
• 24VAC/12DC Dual Voltage

VTC-C770DN
1
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
This symbol is intended to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying the unit.
This symbol is intended to alert the user to the presence of un-insulated "dangerous
voltage" within the product's enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to a person.
Warning (NTSC version) -- This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at their expense.
Caution -- Any changes or modifications in construction of this device that are not expressly
approved by the party responsible for compliance, could void the user's authority to operate the
equipment.
WARNING
Caution
To prevent electric shocks
and risk of fire hazards, do
NOT use other than specific
power source.

VTC-C770DN
2
Table of contents
1. Safety Instructions and Notes…......................................................................................................
2. General Descriptions............................................................................……………………………...
3. Supplied Items......................................................................................……………………………...
4. Part names…………………………….…...................................................…………………………...
5. Installation and Commissioning Instructions....................................................……………………...
6. Setup Menu…………………............................................................................……………………...
7. Specifications…………………………………………….....................................................................
8. Dimensional Drawings….................................................................................................................
3
4
4
5
6
8
19
20

VTC-C770DN
3
1. Safety Instructions and Notes
• Read instructions carefully before putting the camera into operation.
• Keep the operating instructions in a safe place for later use.
• The Standard Box Camera is designed for indoor use only and it must not be installed where exposed
to rain and moisture.
• Do not operate the cameras beyond their specified temperature, humidity or power ratings.
• Never open the case of the camera because there are precision parts inside. An accident may result.
• Do not put anything metallic or foreign through the vent. A fire or electric shock may result.
• Be sure to turn off the power before installing or making connection.
• Pay attention when laying the connection cable and observe that the cable is not subject to heavy
loads, kinks or damage and no moisture can get in.
• Do not install the camera in places exposed to vibrations and shocks.
• Be very careful not to drop or shock the camera while carrying it.
• Do not angle the camera to the sun.
• Do not make any modification to the unit (neither to the software nor the hardware). Improper
modification voids the warranty and can cause malfunctions or damages. The manufacturer accepts
no liability for damages resulting from unauthorized or improper modifications to the unit.
• Some types of lenses may cause hunting, light amount drop or other problems. In such case, readjust
the lenses.
• Because of the digital image device characteristics, images may look rugged at high temperatures.
This does not mean the camera is in trouble.
• The warranty becomes void if repairs are attempted by unauthorized persons.
• Contact the supplier if any functional problems arise.
Cleaning:
• Do not touch the surface of the imaging device.
• Keep front and rear lens surfaces clean.
Notice -- The images used in this manual are processed to help comprehension and may differ from
actual video of the camera.

VTC-C770DN
4
2. General Descriptions
VTC-C770DN (VTC-C770DN/PAL for PAL) is an ultra clear resolution camera that achieves 700TVL
resolution and a crisp color reproduction with the use of Sony 960H EX-view CCD and Effio-E image signal
processor.
With Effio-E digital imaging system,
- Delivers crystal clear images with 700TVL resolution that accurately capture every aspect of any
scene
- Color signal processing provides the optimum balance between the luminance and chroma signals for
high color reproducibility. It even captures detailed scenes that contain very high spatial frequency.
- Incorporates 2-D noise reduction signal processing
With ICR mechanism,
- Enhances its sensitivity about 10x at night
- Accepts infrared light
With 24VAC/12VDC dual power design,
- Offers flexibility of installation
- Ensures reliability
Main features are:
• 1/3" Sony High Density EXVIEW CCD
•Sony Effio Digital Signal Processor
•700TVL High Resolution
•0.003Lux (F1.2@50IRE)
•Supports C/CS mount DC drive lenses
•Supports NTSC & PAL Standards
•Adaptive Tone Reproduction
•2DNR - Two Dimensional Motion Adaptive Noise Reduction
•Motion Detection
•Privacy Mask
•On Screen Display (OSD) Menu
•24VAC/12DC Dual Voltage
3. Supplied Items
1 x ULTRACLEAR RESOLUTION Color Camera
1 x Dust protection cap
1 x Installation and Operating Instructions

VTC-C770DN
5
3
③
1
2
②
4
5
4. Part Names
4.1 Front view
Lens Connector for Auto-iris lens (DC Drive)
1 Back Focus Adjustment 2Dust Protection Cap
3Lens connector for auto iris lenses 4Back focus Adjustment Lock Screw
5Camera Mount Hole (Top and Bottom)
PIN No
DC Iris
1
Damp(-)
2
Damp(+)
3
Drive(+)
4
GND
PIN 4 PIN 2
PIN 3 PIN 1

VTC-C770DN
6
ⓐ
ⓑ
ⓒ
ⓓ
4.2 Rear side view
5. Installation and Commissioning Instructions
•Make sure the power is removed before the installation.
•To apply power:
First connect the low voltage (DC12V or AC24V). Then plug the AC adapter to AC outlets to avoid an
improper reset from power jitter and a damage from the surge voltage when no load.
5.1. Attaching the lens
•Remove the Dust Protection cap from the lens mount
•Screw the lens onto the camera without using force
5.2. Setting the back focus lock
The back focus is the distance between the lens support on the camera and the image sensor. Optimum
focus is only possible when the correct distance is set. It may be necessary to set the back focus in
individual cases due to production tolerances of the lens. The iris of the lens must be open as wide as
possible. (Smallest F value) to set the back focus. For lenses with automatic iris control, you will require an
ND filter (gray filter) to prevent the iris from closing in bright light.
Setting for lenses with a fixed focal distance
If the focus cannot be set exactly by turning the focus ring (lens), please proceed as follows:
ⓐOSD menu switches (Up/ Down/ Left/ Right / Enter)
ⓑVideo Output Connector (BNC)
ⓒPower indicator LED
ⓓPower Input Terminal

VTC-C770DN
7
1. Point the camera at an object with sufficient contrast. The distance to the object should be longer than
1,000 x the focal distance.
2. Open the iris on the lens
3. Set the focus of lens so that the distance at the lens is close to infinity but not to exact infinity position.
4. Loosen Back focus Adjustment Lock: Screw one~two turns on the camera with industrial “+” driver
5. Rotate Back Focus Adjustment until the optimum focus is achieved.
6. Tighten Back focus Adjustment Lock Screw again.
7. Trim the focus precisely at lens if necessary.
Setting for lenses with a variable focal distance (zoom):
If the focus changes as the focal distance changes, please proceed as follows:
1. Point the camera at an object with sufficient contrast at a distance of approximately 2 meters
2. Open the iris on the lens
3. Set the maximum focal distance (Tele) at the lens
4. Set the optimum focus with the focus ring
5. Set the smallest focal distance (wide angle)
6. Loosen Back focus Adjustment Lock. Screw one~two turns on the camera with the industrial “+” driver
7. Adjust Back Focus Adjustment until the optimum focus is achieved. Steps 3,4,5 and 7 may need to be
repeated several times to obtain the best results
8. Tighten Back focus Adjustment Lock Screw again
5.3. Installation
The camera has a 1/4”thread insert on its top and bottom sides for mounting the camera to a tripod, wall
or ceiling with a corresponding mount.
5.4 Commissioning
• First, connect the power supply to the power terminal on the rear panel of camera
• Second, plug the power adaptor to the main supply
• ⓒPower indicator LED will be lit
• The camera is ready for operation
5.5. Power Supply Connections
Camera can work with either 24VAC or 12VDC, dual voltage power. It does NOT require the polarity-
matched connection for 12VDC supply. Primary and secondary grounds are completely isolated to avoid
the possible ground-loop problems. Its excellently wide operating voltage range of 10.5V-30V for DC and
12-28.8V for AC gives extra flexibility at the installation.

VTC-C770DN
8
6. SETUP menu
6.1 In the menu
Use , buttons to move the cursor and , buttons to change the settings.
Press button to select or enter. button stands for MENU or ENTER button.
6.2 MAIN menu
Follow the chart for submenu settings
MAIN menu-1
Default
Descriptions
SHUTTER
/AGC
AUTO
Sets the parameters related to the shutter mode and AGC for AUTO and
MANUAL settings. See '6.3 SHUTTER/AGC menu' for details.
LENS
AUTO
Selects the lens type, AUTO or MANUAL. AUTO supports DC auto-iris lens
only. See '6.4 LENS menu' for details.
DAY/NIGHT
AUTO
Sets DAY/NIGHT mode to AUTO, COLOR or B/W.
AUTO –Camera switches DAY from/to NIGHT automatically.
BURST, DELAY CNT, DAY→NIGHT, NIGHT→DAY can be set.
See '6.5 DAY/NIGHT menu' for details.
COLOR –Day/Night is disabled and forces to DAY mode only.
B/W –Day/Night is disabled and forces to NIGHT mode only.
Camera removes IR cut filter and switches to B/W.
PICTADJUST
-
Sets MIRROR, BRIGHTNESS, CONTRAST, SHARPNESS, HUE or GAIN.
See '6.6 PICT ADJUST menu' for details.
WHITE BAL
ATW
Sets ATW, PUSH, USER1, USER2, ANTI CR, MANUAL or PUSH LOCK.
See '6.7 WHITE BAL menu' for details.
ATR
OFF
Sets ON/OFF for enabling/disabling ATR (Adaptive Tone Reproduction)
compensation for the better dynamic range of the image.
See '6.8 ATR menu' for adjusting the dynamic ranges.
BACKLIGHT
OFF
Selects BACKLIGHT mode out of OFF, HLC or BLC. Areas and gains for
HLC and BLC are factory preset and not user adjustable.
NEXT
Moves to MAIN menu-2.
EXIT
Exits the setup menu. To save the changes, move cursor to 'SAVE ALL'
and press button before exiting the setup menu.
SAVE ALL
Saves all parameters by pressing button.
MAIN menu-1
MAIN menu-2
6.2.1 MAIN menu-1
8

VTC-C770DN
9
6.2.1 MAIN menu-2
6.3 SHUTTER/AGC menu
This menu offers how to control/select SHUTTER,AUTO IRIS and AGC to get the best image for the high
luminance and the low luminance according to the scene.
For example, to reduce the wash out and extend the dynamic range for the highlight scene, it is improved
by SHUTTER+AUTO IRIS in the outdoor daylight. This mode may show color rolling or the video level
hunting problem in certain lighting condition such as fluorescent lights.
Flickerless mode reduces the flickers by NTSC camera under 50Hz light or PAL camera under
60Hz light. MAIN> SHUTTER/AGC> MANUAL> SHUTTER must be set to 1/100 (NTSC), 1/120 (PAL) and
MAIN> SHUTTER/AGC> AUTO> MODE to AUTO IRIS. Normal shutter speed with an auto iris lens
should be set to 1/60 (NTSC) and 1/50 (PAL) for the best sensitivity.
To enter SHUTTER/AGC menu, press button at MAIN menu-1>SHUTTER/AGC.
MAIN menu-2
Default
Descriptions
NR
-
Sets the noise reduction parameters for NR MODE, Y LEVEL and
C LEVEL. See '6.9 NR menu' for details.
MOTION DET
OFF
Sets ON/OFF for enabling/disabling MOTION DET.
See '6.10 MOTION DET menu' for the parameter settings.
PRIVACY
OFF
Sets ON/OFF for enabling/disabling PRIVACY.
See '6.11 PRIVACY menu' for the parameter settings.
LANGUAGE
ENGLISH
Selects the language out of 7 languages.
CAMERA ID
OFF
Sets ON/OFF for enabling/disabling of ID display.
Factory default ID is this version of the camera.
User programmed camera ID will be lost and restored with Factory default
ID after CAMERA RESET. See '6.12 ID menu' for editing ID.
CAMERA
RESET
Restores FACTORY DEFAULT.
To save the restored parameters, move cursor to 'SAVE ALL' and press
button before exiting the setup menu.
BACK
Returns to MAIN menu-1.
EXIT
Exits the setup menu.
To save the changes, move cursor to 'SAVE ALL' and press button.
SAVE ALL
Saves all settings by pressing button.

VTC-C770DN
10
6.3.1 SHUTTER/AGC>AUTO SETUP menu
NOTICE : The setting AUTO IRIS at SHUTTER/AGC>AUTO SETUP>HIGH LUMINANCE MODE will be
changed to SHUT+AUTO IRIS if MAIN menu-1>LENS is changed to MANUAL.
As a result, the lens iris can NOT be fully opened when MAIN menu-1>LENS>AUTO IRIS>
MODE is OPEN.
This can be recovered by setting SHUTTER/AGC>AUTO SETUP>HIGH LUMINANCE MODE
to AUTO IRIS.
AUTO SETUP
Default
Descriptions
MODE
AUTO
IRIS
Selects the shutter mode from AUTO IRIS or SHUT+AUTO IRIS when
MAIN>LENS>AUTO but it is fixed to SHUT if MAIN>LENS>MANUAL.
AUTO IRIS - Light level is controlled by an auto iris lens only.
For proper auto iris operation, the auto iris operation mode in MAIN>
LENS>AUTO>MODE must be set to AUTO.
The shutter speed is fixed to the setting at MAIN>SHUTTER/AGC>
MANUAL> SHUTTER in this mode.
Set SHUTTER to 1/60 (NTSC) or 1/50 (PAL) for the best sensitivity
unless it is in Flickerless mode.
To set Flickerless mode: MAIN>SHUTTER/AGC>MANUAL>SHUTTER
must be set to 1/100 (NTSC), 1/120 (PAL) and MAIN>SHUTTER/AGC>
AUTO>MODE to AUTO IRIS.
SHUT+AUTO IRIS- Light level is controlled by the combination of an
auto iris lens and shutter control to improve the highlight from wash-
out and extend the dynamic range. Shutter speed can vary between
1/60(1/50)~1/10,000sec.
This mode enhances the overall video quality of daylight but may show
a smeared image in bright spotlights. However, color rolling or video
level hunting may occur under a certain lighting condition such as
fluorescent lights.
BRIGHT-
NESS
032
Adjusts the brightness of the image by an auto iris lens or a shutter
speed control + an auto iris lens.
MODE
AGC
Sets AGC to compensate the video level when the scene is dim.
BRIGHT-
NESS
x0.50
Sets the brightness level which starts AGC from x0.25, x0.50, x0.75 and
x1.0 of full video level.
If set to x0.50, the camera will start AGC when the video level goes
down to below the 50% level.
HIGH LUMINANCE
LOW LUMINANCE

VTC-C770DN
11
6.3.2 SHUTTER/AGC>MANUAL SETUP menu
6.4 LENS menu
To enter LENS menu, press button at MAIN menu-1>LENS>AUTO.
6.5 DAY/NIGHT menu
To enter DAY/NIGHT menu, press button at MAIN menu-1>DAY/NIGHT
AUTO IRIS
Default
Descriptions
TYPE
DC
MUST BE SET TO DC ONLY.
This camera does NOT support video type auto iris lens.
MODE
AUTO
AUTO –Lens iris is automatically controlled according to the scene‟s
light level.
OPEN –Lens is fully opened regardless of the light level.
CLOSE –Lens is fully closed.
SPEED
080
Adjusts the iris control speed.
The lower the value, the faster the speed.
If the speed is too slow or fast, the iris control may be unstable.
MANUAL
SETUP
Default
Descriptions
MODE
SHUT
+AGC
Compensates the video level by the manual shutter control and AGC.
SHUTTER
1/60
(1/50)
Sets the manual shutter to 1/60(1/50), 1/100(1/120), 1/250,1/500,1/1000,
1/2000,1/4000 or 1/10000.
Manual shutter is only useful when luminance is unchanged.
AGC
6.00
Sets AGC gain in dB. Higher gain compensates for a brighter scene, but
noise increases.
Manual AGC can be set to 6, 12, 18, 24, 30, 36, 42 or 44 8dB.

VTC-C770DN
12
IMPORTANT ACTIVITY!!!
DAY->NIGHT and NIGHT->DAY operations must be examined and verified at the final
installation.
Block the lens for a few seconds for NIGHT mode, then release and let it return to DAY mode.
If camera stays at NIGHT mode for more than 10sec, slightly increase „N→D THRES‟ and repeat the fore-
mentioned steps.
If the scene is too dim or the lens iris was adjusted too low (near close), it may not return to DAY.
DAY/NIGHT
Default
Descriptions
BURST
OFF
BURST mode contains color burst signal when the camera switches to B/W.
ON mode maintains the same color signal in B/W so that the video signal
provides better compatibility with certain color equipment.
OFF mode removes the color burst signal B/W video and increase the total TV
lines.
DELAY
CNT
005
DELAY CNT is the time in seconds before Day↔Night switches. DELAY can
avoid the unwanted/frivolous switching of short term lights such as light from
a passing car.
DAY→NIGHT
005
DAY→NIGHT mode sets a threshold level to determine when switch from
DAY to NIGHT. Lower (Higher) value makes the camera switched from Day to
Night at lower (higher) illumination.
If the camera stays in Color at night time, increase DAY→NIGHT threshold
value until it just switches to Night.
CAUTION If the value between DAY→NIGHT and NIGHT→DAY is
minimal, then camera may switch between DAY and NIGHT mode
repeatedly.
NIGHT→
DAY.
3
NIGHT→DAY mode sets a threshold level to determine when to switch from
NIGHT to DAY. Lower (Higher) value makes the camera switched from Night
to Day at lower (higher) illumination.
If the camera stays in B/W mode during day time, decrease NIGHT→DAY
threshold value until it switches to Day.
CAUTION If the value between DAY→NIGHT and NIGHT→DAY is
minimal, then camera may switch between DAY and NIGHT mode
repeatedly.

VTC-C770DN
13
6.6 PICT ADJUST menu
To enter PICT ADJUST menu, press button at MAIN menu-1>PICT ADJUST.
6.7 WHITE BAL menu
White balance can be set to ATW, PUSH, USER1, USER2, ANTI CR, MANUAL or PUSH LOCK.
ATW (Auto Tracking White balance) and PUSH (Full pull-in) are continuously monitoring/analyzing the color
temperature of the incoming light and correcting the white balance.
ATW limits the color temperature range at about 2,500˚K~8,500˚K to reduce the excessive compensation
for the big object which has a single color.
PUSH has no limits between about 1,800˚K~10,500˚K but it may over-compensate the white balance for
the big object which has a single color.
In cases where it goes under 2,500˚K such as halogen light, ATW may stop. If so, PUSH mode is
recommended.
USER1 and USER2 are a fixed white balance which is user-programmable by R-GAIN and B-GAIN and
useful only for the steady light.
ANTI CR (Anti Color Rolling) can reduce color rolling under the fluorescent light when the camera
operates in shutter control without an auto iris lens. (NTSC version only)
PICTADJUST
Default
Descriptions
MIRROR
OFF
Picture will be flipped horizontally if it turns ON.
BRIGHTNESS
000
Increases or decreases the brightness of the picture.
This is different from that of DC iris lens because it simply increases or
decreases the digital gain of the video.
Do not increase this too much or the dynamic range for the highlight area
will decrease.
CONTRAST
120
Increases or decreases the contrast of the picture.
SHARPNESS
128
Increases or decreases the sharpness of the picture.
Too much sharpness can make the image too harsh and show more noise
as well as line flicker at the edge of object in the picture.
HUE
128
Adjusts hue for NTSC version only.
GAIN
128
Increases or decreases the color gain of the picture.

VTC-C770DN
14
MANUAL white balance is a kind of fixed white balance which is user-programmable by B-GAIN.
(R-GAIN will be automatically adjusted in accordance with B-GAIN) and useful only for the steady light.
PUSH LOCK is a fixed white balance where the white balance is compensated only while the button is
pressed at MAIN>WHITE BAL>PUSH LOCK and finishes the white balance when button is released.
To enter ATW (MANUAL) menu, press button at MAIN menu-1>WHITE BAL>ATW(MANUAL).
MANUAL WB
Default
Descriptions
LEVEL
064
Manual White Balance Adjustment value.
ATW
Default
Descriptions
SPEED
250
Sets the AWB compensating speed. Lower value makes AWB faster.
CAUTION Too fast an AWB may force color oscillation.
DELAY CNT
001
Adjusts the AWB compensation period to next update of AWB.
The smaller value will update AWB more frequently (faster).
ATW FRAME
X2.00
Determines the ATW range with respect to the fundamental range.
A higher value than x1.00 extends the ATW range at lower and higher color
temperature.
ENVIRON-
MENT
INDOOR
Selects INDOOR or OUTDOOR.
Their ATW is optimized for the limited application and cannot cover.
INDOOR - Optimized for Indoor installation and compensates ATW for low
color temperature such as incandescent lights.
OUTDOOR - Optimized for outdoor sunlit applications and compensates
ATW for high color temperature such as daylight.

VTC-C770DN
15
6.8 ATR (Adaptive Tone Reproduction) menu
The ATR feature improves the dynamic range and the visibility of the image by providing the optimal
gradation compensation of the image in one field. This is achieved by two ways of image processing,
luminance compression and contrast enhancement, so that the tone can be enhanced at highlighted and dark
areas.
To enter ATR menu, press button at MAIN menu-1>ATR.
ATR
Default
Descriptions
LUMINANCE
MID
Compresses the highlighted area and enhances the dark area so that the
entire image can converge toward the medium level.
LOW will compensate minimally and HIGH will average out the image.
With setting HIGH, the image may look less contrastive and noise may
increase in the dark area.
CONTRAST
MID
Adjusts the strength of the image contrast.
If set to too high, the dark area may lose detail and the high luminance
area may saturate.

VTC-C770DN
16
6.9 BACKLIGHT menu
To enter BACKLIGHT menu, press button at MAIN menu-1>BACKLIGHT.
6.10 NR menu
To enter NR menu, press button at MAIN menu-2>NR.
HLC OFF
HLC ON
BLC OFF
BLC ON
NR
Default
Descriptions
NR MODE
Y/C
Selects OFF, Y, C or Y/C which noise reduction is performed with.
Y LEVEL
006
Indicates the noise reduction strength for the luminance signal.
Higher value performs stronger noise reduction and makes the image
less sharp. Due to the limitation of 2D NR, noise reduction may not be
effective enough.
C LEVEL
004
Indicates the noise reduction strength for the chrominance signal.
Higher value performs stronger noise reduction and makes the image
less sharp. Due to the limitation of 2D NR, noise reduction may not be
effective enough.
16

VTC-C770DN
17
6.11 MOTION DET menu
Up to 4 motion detection areas are available and each area is programmable in size and location.
The motion is displayed by means of blocks when MAIN menu-2>MOTION DET and MOTION
DET>BLOCK DISP are ON.
To enter MOTION DET menu, press button at MAIN menu-2>MOTION DET>ON.
6.12 PRIVACY menu
Up to 8 privacy areas are available and each area is programmable in size and location.
The number of privacy areas is limited to four when MOTION DET>MONITORAREA is ON.
The privacy areas are masked with the color selected by PRIVACY>COLOR.
To enter PRIVACY menu, press button at MAIN menu-2>PRIVACY>ON.
MOTION DET
Default
Descriptions
DETECT SENSE
080
Adjusts the sensitivity for detecting motion. Ahigher value is more sensitive.
BLOCK DISP
ON
Enables or disables displaying blocks for the area where the motion is
detected.
MONITOR
AREA
OFF
Displays four motion windows as programmed in sizes and positions.
AREA SEL
1/4
Selects AREA1~AREA4 to be adjusted.
TOP (BOTTOM) - button moves up and button moves down the top
(bottom) border of the selected window at AREA SEL.
LEFT (RIGHT) - button moves left and button moves right the left
(right) border of the selected window at AREA SEL

VTC-C770DN
18
6.13 LANGUAGE menu
Seven languages, ENGLISH ,JAPANESE, DEUTCH, FRANCAIS, RUSSIAN, PORTUGUES and
ESPANOL, are available with this camera.
6.14 CAMERA ID menu
Up to 40 characters can be input for camera ID.
To enter CAMERA ID menu, press button at MAIN menu-2>CAMERA ID.
Use , , , buttons to move a block cursor in character table and press button to input the
selected character.
To move the character input position on CAMERA ID input line, move a cursor to ←→ on COMMAND LINE
and press button on ← or →.
To clear CAMERA ID input line, move a cursor to CLR on COMMAND LINE and press button.
To set the location of CAM TITLE to be displayed on the monitor, move a cursor to POS and press button.
Then, the menu will disappear and the CAMERA ID will be displayed on the monitor.
Move CAMERA ID by using , , , buttons and press button to fix.
Menu will appear again.
To finish CAM TITLE menu, press button on RET on command line.
PRIVACY
Default
Descriptions
AREA SEL
1/8
Selects one ofAREA1~AREA8 to be adjusted.
TOP(BOTTOM) - button moves up and button moves down the top
(bottom) border of the selected window at AREA SEL.
LEFT(RIGHT) - button moves left and button moves right the left
(right) border of the selected window at AREA SEL
COLOR
1
Sets one of 8 colors for the selected mask window at AREA SEL.
TRANSP
1.00
Transparency rate for the mask can be adjusted.
0.00 - Mask is fully transparent and not visible.
0.50 - Mask is 50% transparent.
0.75 - Mask is 25% transparent.
1.00 - Mask is not transparent.
MOSAIC
OFF
Enables or disables the mosaic effect for the selected mask window at
AREA SEL
COMMAND LINE
CAMERA ID input line

VTC-C770DN
19
6.15 CAMERA RESET
Camera loads Factory defaults.
To save them, go to SAVE ALL and press button.
6.16 EXIT
Exits SETUP MENU and returns to the normal display
7. Specifications
Model name
VTC-C770DN
VTC-C770DN/PAL
Image Device
1/3” Sony High Density EXVIEW CCD
Image Processor
Sony Effio Digital Signal Processor
Effective Pixels
976(H) x 494(V)
976(H) x 582(V)
Scan Frequency
59.94Hz(V), 15.734Khz(H)
50Hz(V), 15.625Khz(H)
Synchronization
Internal
H. Resolution
700TV Lines
Sensitivity
0.0003Lux at F1.2@50IRE
S/N Ratio
More than 50dB with AGC OFF at 50IRE
White Balance
1,800 ~ 10,500ºK Automatic tracking
Scan System
2:1 Interlace
Motion Detection
YES (24 x 16 BLOCK ALARM AREA)
Privacy Mask
8 mask
Adaptive Tone Reproduction
[On or Off / Luminance –Low, Middle, High & Contrast –Low, Midlow,
Midhigh, High]
OSD Language
EN, FR, DE, ES, POR, SC, RUS, JP
Day & Night
True Day and Night by ICR
Lens Mount
C/CS (C-mount ring –optional)
Video Output
VBS 1 Vpp +/- 10%, 75ohm
Operating Power
24VAC/12VDC
Operating Condition
-4‟F ~ 122‟F / -20‟C ~ 50‟C, 85% RH. Max. Non-condensing
Dimension
(W x H x L)
65mm x 55mm x 126mm (2.6in x 2.2in x 4.9in) About 400g/.9lb (Net)
● Design and specifications are subject to change for product improvements without prior notice.