Vitek VTC-T4T3HR2MD User manual

VITEK
VITEK
FEATURES
• 1/2.9” 2.1 Megapixel Sony® Exmor™ Progressive Scan
CMOS Sensor
• 30fps live view @ 1920 x 1080p
• True Day/Night by IR Cut Filter
• HD-TVI / HD-CVI / AHD / 960H CVBS Video Output
(Selectable)
• Motorized 2.8~12mmMegaPixel IR Corrected Auto Focus
Varifocal Lens with CoC
• 3 Integrated High Power Dynamic IR LEDs with up to 115’
IR Range
• 3D-DNR Noise Reduction
• True Wide Dynamic Range (WDR)
• 16:9 Video format
• IP66 Weather Resistance
• Supports Up The COAX Control (CoC)
• Over 1500’ HD Video Transmission (Depending on cable
characteristics and integrity)
• Optional Junction Box Mount Available (VT-TJB04A)
• 12VDC / 24VAC Dual Voltage Operation
• 3 Year Warranty
VTC-T4T3HR2MD
2.1 Megapixel 4-IN-1 HD-TVI /
AHD / CVI / CVBS Motorized
Varifocal WDR Ball/Turret
Camera w/IR LED Illumination

2 3
Safety Precaution
CAUTION: TO REDUCE THE RISK OF ELECTICAL
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
To prevent electrical shock and risk of fire hazards, do not expose this unit
to rain or moisture and only use specified power source..
Warning :
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
their own expense.
Caution :
Any changes or modifications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user's authority
to operate the equipment.
Main power quality should be that of a typical commercial environment. If the user
of the model requires continued operation during power interruptions, it is
recommended that the device be powered from an uninterruptible power supply
(UPS).
The symbol is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature
accompanying the unit.
The symbol is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electrical shock.

3
Power & Video Connections
Monitor
Video
12VDC / 24VAC Power
Connect the HD-TVI Video or AHD/CVBS video connector to a BNC
patch cable, then to a DVR. Next connect the power connector to a
12VDC or 24VAC power adaptor.
Installation
1) Disconnect power before installation.
2) Confirm proper 12VDC or 24VAC power supply is used to prevent
damage to the camera.
3) Do not use in an environment beyond the boundaries of the
specifications.
Video Output Mode Switch:
Select the desired video mode using the dip switches
contained within the on-cable Output Mode Switch as follows:
ON
12
ON
12
CVBS
ON
12
AHD
ON
12
HD-TVI
ON
12
CVI

4 5
OSD Instruction
1. IRIS
2. 2-MOTOR
IRIS ALC
2-MOTOR
EXPOSURE
BACKLIGHT OFF
DAY&NIGHT
COLOR
DNR LOW
IMAGE
MOTION OFF
SYSTEM
EXIT
IRIS ELC
2-MOTOR
EXPOSURE
BACKLIGHT OFF
DAY&NIGHT
COLOR
DNR LOW
IMAGE
MOTION OFF
SYSTEM
EXIT
2-MOTOR
AF (Auto Focus))
Choose between Auto focus and Manual focus.
SCANNING
When Lens scans Half or Full for focusing.
SYNC TDN
Lens scans Half or Full for focusing. Adjust lens
when switching from Day to Night or Night to Day.
INITIAL
Sets lens parameters from close to far.
IRIS
Electronic Light Control (ELC)
When using a fixed or manual iris lens, the
camera's ELC can adjust for moderate changes in
illumination levels. While it is fine for indoor
applications in fixed illumination conditions, a
fixed iris and ELC circuitry cannot approach the
range of illumination usable with an auto-iris lens
and ALC circuitry.
Automatic Light Control (ALC)
When using an auto-iris lens, the ALC circuitry
samples the illumination level and automatically
adjusts the iris to create the proper sized aperture
for proper exposure.
BACKLIGHT OFF
DNR LOW
MOTION OFF
AF MODE AUTO
SCANNING HALF
ONE PUSH AF ON
SYNC TDN ON
INITIAL ON
RETURN

5
3. EXPOSURE
4. BACKLIGHT
IRIS ELC
2-MOTOR
EXPOSURE
BACKLIGHT BLC
DAY&NIGHT
COLOR
DNR LOW
IMAGE
MOTION OFF
SYSTEM
EXIT
BACKLIGHT
BACKLIGHT
OFF/HLC/BLC/WDR, used in different environment.
HLC (High Light Compensation)
Cuts out the bright area with a mask and excludes it
from compensation..
LEVEL (0~20)
Sets the HLC level. It determines the video level that
starts cutting out. Lower setting starts the cut out at a
lower light level. The cut out area is masked with
selected color.
COLOR
Select mask color from 9 colors. Black, White,
Yellow, Cyan, Green, Magenta, Red, Blue and
Customize.
BLC (Backlight Compensation)
Compensates the video image by cutting out the
bright areas with a mask or adjusting the contrast of
the video. This function is used to brighten an image
in the foreground with a bright light area behind it
such as sunlight, limiting the affect of silhouette. BLC
has a target window for compensation and its size
and position can be set by H-POS, V-POS, H-SIZE and
V-SIZE.
H-POS, V-POS
Sets the position of BLC area to move vertically and
horizontally.
H-SIZE, V-SIZE
Sets the size of BLC area to move vertically and
horizontally.
WDR:
HIGH/ MIDDLE/ LOW level，selectable, 30fps.
Note:CVBS will stop when WDR is turned on.
EXPOSURE
BRIGHTNESS
0-20 selectable.
SHUTTER
AUTO/FLICKER/MANUAL
MANUAL MODE
1/25、1/50、1/100、1/200、1/400、1/800、1/1600、
1/3200、1/6400、1/12800、1/25600、1/30000,
selectable.
AUTO
DEBLURE/NORMAL., selectable.
SENS-UP
OFF、X2、X4、X8、X16、X32 selectable.
AGC
0-20 selectable
DNR LOW
IMAGE
MOTION OFF
H-POS 6
V-
POS 4
H-SIZE 5
V-SIZE 3
RETUREN
IRIS ELC
2-MOTOR
EXPOSURE
BACKLIGHT OFF
DAY&NIGHT
COLOR
DNR LOW
IMAGE
MOTION OFF
SYSTEM
EXIT
BACKLIGHT OFF
DNR LOW
IMAGE
MOTION OFF
BRIGHTNESS
SHUTTER MANUAL
SENS UP X2
AGC
RETURN
SHUTTER MANUAL

6 7
5. DAY&NIGHT
6. COLOR
IRIS ELC
2-MOTOR
EXPOSURE
BACKLIGHT OFF
DAY&NIGHT
COLOR
DNR LOW
IMAGE
MOTION OFF
SYSTEM
EXIT
IRIS ELC
2-MOTOR
EXPOSURE
BACKLIGHT OFF
Day& NIGHT EXTERN
COLOR
DNR LOW
IMAGE
MOTION OFF
SYSTEM
EXIT
DAY & NIGHT
Switch settings of Day and Night mode.
AUTO
Used when DAY or NIGHT is determined by light
level through the lens.
COLOR
The camera is always in COLOR mode. DAY/NIGHT
is disabled and outputs color video
B&W
The camera is always in B/W mode. Forcibly
removes IR cut filter and switches to B/W regardless
of light level.
EXTERN
DAY or NIGHT is determined by the built-in light
photo sensor for cameras with built-in IR LEDS.
ANTI-S AT
Sets the anti saturation level 0~20. Setting high
level avoids saturation but the corners will be
darker accordingly.
D＞N THRES & N＞D THRES
Sets the light level for switching from Day to Night /
Night to day.
D EL AY
Is time in seconds while camera maintains its status
before Day to Night / Night to Day switching. (Only
available when mode is AUTO or EXTERN).
COLOR
AWB (Auto White Balance)
Automatically tracks the changes of color
temperature and continuously adjusts the white
balance. AUTO, AUTOext, PRESET and MANUAL
modes are available.
AUTO
Optimized for Indoor installation and compensates
AWB for low color temperature such as
incandescent lights.
AUTOext
Optimized for outdoor sunlight applications and
compensates AWB for high color temperature such
as sunlight.
PRESET
AWB is performed only whenever button is pressed.
MANUAL
White balance is fixed to the settings by
Color-Temperature Red-GAIN and Blue-GAIN. It can
be used only when the color temperature does not
va r y.
DNR LOW
MOTION OFF
ANTI-SAT.
EXTERN SW NONE
D＞N THRES
N＞D THRES
DELAY LOW
RETURN
DNR LOW
IMAGE
MOTION OFF
WB MANUAL
COLOR GAIN
RETUEN

7
7. DNR
8. IMAGE
IRIS ELC
2-MOTOR
EXPOSURE
BACKLIGHT OFF
DAY&NIGHT
COLOR
DNR LOW
IMAGE
MOTION OFF
SYSTEM
EXIT
DNR
3D-NR (Digital Noise Reduction)
DNR function improves picture quality by filtering
out signal noise which is generated under low light
conditions. Set off, low, middle or high level. 3DNR
(3-dimensional noise reduction) which reduces
noise by multi frames. It is effective in low light. Set
to high will reduce the most noise but the image
will be less sharp and a tailing effect might occur.
IMAGE
SHARPNESS
Sets the Sharpness level 0~10. Increases or
decreases the sharpness of the picture. Too much
sharpness can make image harsh and show more
noise as well as line flicker at the edge of object in
the picture
GAMMA
Used to adjustment the monitor GAMMA value
0.45/0.55/0.65/0.75 selectable.
ORIENTATION
NORMAL / MIRROR / FLIP / MIRROR_V.
ACE
Improves the visibility for the bright areas and the
dark areas by compensating the video gain. Care
should be taken to select low, middle or high level,
because video may lose its quality in some
environments by over compensation. Video noise
can be increased in the dark area accordingly
DEFOG
Enhance foggy video according to status of scene.
Vide
o quality can be less in normal environments.
PRIVACY
Set ON/OFF for enabling/disabling PRIVACY mask.
16 privacy areas are available and each area is
programmable in size, color, position and
transparency.
ZONE NUM
Selects mask zone number from 0 to 16 to be
adjust.
‘
ZONE DISP
Displays OFF/ON for the mask area which you
selected.
H-POS, V-POS
Adjusts the mask area H, V position which you
selected.
TRANS
Selects transparency rate for the mask area from 0
to 3
DNR LOW
IMAGE
MOTION OFF
SYSTEM
SHARPNESS
GAMMA 0.55
ORIENTATION NORMAL
FLIP OFF
ACE OFF
DEFOG ON
PRIVACY
RETURN
IRIS ELC
2-MOTOR
EXPOSURE
BACKLIGHT OFF
DAY&NIGHT
COLOR
DNR LOW
IMAGE
MOTION OFF
SYSTEM
EXIT

8 9
9. MOTION
IRIS ELC
2-MOTOR
EXPOSURE
BACKLIGHT OFF
DAY&NIGHT
COLOR
DNR LOW
IMAGE
MOTION ON
SYSTEM
EXIT
MOTION
3 motion detection areas are available and each
area is programmable in size and location.
Motion can be detected in the area and
displays the results in blocks and/or a text
message
DET WINDOW
WINDOW ZONE : Set the detection zone
number from 0 to 3.
H-POS
0-60 horizontal starting point.
V-POS
0-34 vertical ending point.
H-SIZE
0-60 horizontal ending point.
V-SIZE
0-34 vertical ending point.
DET ZONE
Sets the detection zone 0 to 4 display types
which window use setting ON.
0) Set 100% opacity level of video background
except detection window zone.
1) Set 50% opacity level of video background
except detection window zone.
2) Set 25% opacity level of video background
except detection window zone.
3) Video background image is same as
detection window zone.
4) Detection window zone is displayed with box
line
MDRECT FILL
Sets the motion display type when motion is
detected in video. Setting ON will display a red
solid box type. Setting OFF will display a red
outline box type
Sensitivity
Sets the detection sensitivity for motion (0~10).
Higher values increases the sensitivity to detect
motion. Too low of a value will cause the erratic
detection by tree leaves or light level changes
MOTION OSD
Set ON or OFF to display motion results.
TEXT ALARM
Setting ON enables to display a text message
“WINDOWS MOVING!!” or icon when motion
is detected.
SYSTEM
DET WINDOE
DET TONE 2
MORECT FILL OFF
SENSITIVITY
MOTION OSD OFF
TEXT ALARM OFF
SIGNAL OUT OFF
RETURN

9
10. SYSTEM
IRIS ELC
2-MOTOR
EXPOSURE
BACKLIGHT OFF
DAY&NIGHT
COLOR
DNR LOW
IMAGE
MOTION OFF
SYSTEM
EXIT
SYSTEM
COM.
RS-485 Communication setting ID: 0-255,
BAUDRATE: 2400/4800/9600/57600/115200
selectable.
IMAGE RANGE
USER/FULL/COMP, the OFFSET of USER: 0-32.
COLOR SPACE
HD-CbCr、YUY、SD-CbCr.
FRAME RANGE
1080P/720P_ (25fps/30fps), selectable.
Monitor
0-3, choose a different screen style.
FREQ
NT SC/PAL.
CVBS
ON/OFF.
LAUGUAGE
Multiple languages CHN [S], CHN，EN、JPN
KOR、I TA
COLOR BAR
OFF/ON，used in color contrast test (color bar
on screen).
CAM TITLE
Using the OSD button select letters by
pushing button up, down, left or right.
RESET
Hold OSD button for 10 seconds to reset
camera
COLOR
DNR LOW
IMAGE
MOTION OFF
SYSTEM
DNR LOW
COM.
IMAGE RANGE USER
COLOR SPACE HD-CbCr
FRAME RATE 1080P_30FPS
Monitor 0-3
FREQ PAL
CVBS ON
LANGUAGE CHN[S]
COLOR BAR
CAM TITLE OFF
RESET ON
RETURN
IMAGE RANGE USER

10 11
CONSIDER THESE OTHER GREAT
TRANSCENDENT PRODUCTS!
VT-TJB04A
Optional Junction Box for Cable
Management for use with VTC-
T4T3HR2MD & VTD-T4D24R2MD
• 4, 8, 16, or 32 Channel HD-TVI / AHD / CVI / CVBS BNC Inputs + IP Camera Support
• 1-Channel IP Camera Support (VT-TTAR410 / VT-TTAR810) / 4-Channel IP Camera
Support (VT-TTAR1620 / VT-TTAR3280)
• 960fps @ 720p & 1080P-Lite / 480fps @ 1080p Recording
• Simple plug and play, point-to-point connection from camera to DVR
• H.264 Compression
• HDMI, VGA, and BNC (Spot) Video Outputs
• 2-Way Audio
• PTZ Control over RS-485
• 16 Alarm inputs / 4 Alarm Output
• Pentaplex: Live Display / Record / Playback / Backup / Remote Access
• 1 Internal SATA2/SATA3 HDD Slot supporting up to 8TB (1 x 8TB HDD) (VT-TTAR410
/ VT-TTAR810) / 2 Internal SATA2/SATA3 HDD Slots supporting up to 16TB (2 x 8TB
HDD) (TTAR1620) / 8 Internal SATA2/SATA3 HDD Slots supporting up to 64TB (8 x
8TB HDD) Internal Storage (VT-TTAR3280)
• Applications for iOS & Android
• Remote Viewing over the Internet via Web Browser or LAN
• Mac OS® Client & CMS Central Management Software Included
• Supports both Dynamic and Static IP Addresses
• Control locally via USB Mouse, or with the Included IR Remote control
• 3 Year Warranty
VT-TTAR Series
Transcendent Series 4, 8, 16, and 32 Channel 5-In-1 HD-TVI / AHD /
CVI / 960H / IP Digital Video Recorders

10 11
Detailed Specifications
Image Sensor
Signal System
Effective Pixels
Resolution
Video Output
Lens
Day/Night
Min. IIIumination
IR LEDs
IR Distance
DSS (Sens-Up)
S/N Ratio
WDR
Digital Noise Reduction (DNR)
White Balance
BLC
Defog
Privacy Mask
Motion Detection
Up the COAX Control (COC)
Transmission Distance
Power Input
Power Consumption (12VDC)
Power Consumption (24VAC)
Weather Resistance
Operation Conditions
Weight
Dimensions
1/2.9” 2.1 Megapixel Sony® Exmor™ Progressive Scan CMOS Sensor
PAL/NTSC
1920(H) × 1080(V)
HD-TVI / HD-CVI / AHD: 1080p/720p (2.1 MegaPixel) / CVBS: 960H
HD-TVI / HD-CVI / AHD / CVBS (Selectable)
Motorized 2.8~12mm MegaPixel IR Corrected Varifocal Lens
True Day/Night by ICR
0.001 Lux @ f2 (B/W) / 0.1Lux @ F2.0 (Color) / 0 Lux (IR ON)
3x High Power Dynamic IR LEDs
115’
OFF / X2 ~ X32
≥50dB (AGC Off)
True WDR
3D-DNR
Auto / Present / External / Manual
Adjustable
Adjustable
16 Programmable Areas
4 Programmable Areas
YES
Up to 1500’ (Depending on cable characteristics & integrity)
Dual Voltage: 12VDC / 24VAC
650mA (IR ON) / 220mA (IR OFF)
325mA (IR ON) / 110mA (IR OFF)
IP66
-4~122 / 10%~90% Humidity
28.22 oz. / 1.76 lbs. / 800g
5.23” x 3.46” x 5.70” (132.86 x 88 x 144.9mm)

28492 CONSTELLATION ROAD VALENCIA, CA 91355
WWW.VITEKCCTV.COM
Version 1.0
December 2017
LIMITED PRODUCT WARRANTY
VITEK products carry a three (3) year limited warranty. VITEK warrants
to the purchaser that products manufactured by VITEK are free of any
rightful claim of infringement or the like, and when used in the manner
intended, will be free of defects in materials and workmanship for a
period of three (3) years, or as otherwise stated above, from the date of
purchase by the end user. This warranty is nontransferable and extends
only to the original buyer or end user customer of a VITEK Authorized
Reseller.
The product must have been used only for its intended purpose, and
not been subjected to damage by misuse, willful or accidental damage,
caused by excessive voltage or lightning.
The product must not have been tampered with in any way or the
guarantee will be considered null and void.
This guarantee does not affect your statutory rights.
Contact your local VITEK Reseller should servicing become necessary.
VITEK makes no warranty or guarantee whatsoever with respect to
products sold or purchased through unauthorized sales channels.
Warranty support is available only if product is purchased through a
VITEK Authorized Reseller.