Vitek VTC-IRE24F User manual

VITEK
• 1/3” High Resolution CCD
• 700 TV Lines of Resolution (960H)
• E-WDR by Adaptive Tone Reproduction
• 24 Dynamic Infrared LEDs with up to 65’ Range
• 0.003 Lux / 0 Lux with IR LEDs On
• IR Corrected 3.6mm Fixed Iris Lens
• 2DNR Noise Reduction
• Motion Detection, Privacy Masking & Highlight Masking
• OSD (On Screen Display) menu and Camera ID
• IP-67 Rated Water Resistance
• Cable Feed Through Mount for tamper resistance
• 12 VDC Operation
VTC-IRE24F
Day/Night 960H Infrared
Bullet Camera

CAUTION:
To reduce the risk of electric shock, do not expose this apparatus to rain or moisture.
Only operate this apparatus from the type of power source indicated on the label.
The company shall not be liable for any damages arising out of any improper use, even if we
have been advised of the possibility of such damages.
PACKAGE CONTENTS
CONNECTION
1 x VTC-IRE24F Camera
1 x Mounting Bracket
1 x User Manual
1 x Hex Wrench
1 x Mounting Screws/Anchors Pack
1 x Mounting Template
1. Connect the camera video output to the monitor video input with a 75Ω coaxial
cable.
2. DC12V Input Terminal
Connect the power connector of the camera to a 12V DC regulated power supply.
NOTE: Please use the correct power adaptor, DC12V (regulated), to operate this
unit. The tolerance of this unit is DC12V ± 10%. Over the maximum DC12V power
input will damage the video output connector (VIDEO OUT).
CAUTION
RISK OF ELECTRICAL SHOCK
DO NOT OPEN
The lightning fl ash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of suffi cient magnitude to constitute
a risk of electric shock to persons.
This exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.

VTC-BRE24F / VTC-IRE24F
1
The lightning flash with an arrowhead symbol, within an equilateral
triangle is intended to alert the user to the presence of non-insulated
dangerous voltage within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing) instructions
in the literature accompanying the appliance.
This installation should be made by a qualified service person and should conform to all local codes.

VTC-BRE24F / VTC-IRE24F
2
Contents
1. EXPOSURE
2. DAY & NIGHT
3. WHITE BAL
4. MONITOR
5. IMAGE
6. DNR
7. MOTION
8. SYSTEM
9. EXIT

VTC-BRE24F / VTC-IRE24F
3
Warning
Contact an authorized technician for inspection.
If you use your camera around smoke or unusual heat for a long time, fire may
be caused.
Unless the surface is suitable, it could cause falling or other hazards.
It may result in fire, electric shock or other hazards.
It could cause an electric shock.
It
may result in fire or other hazards.

VTC-BRE24F / VTC-IRE24F
4
[OSD Menu]
EXPOSURE
ALC / ELC
DAY / NIGHT
DAY / NIGHT / AUTO / EXTERNAL / CDS
WHITE BAL
MANUAL / PUSH / ATW
MONITOR
GAMMA / CHROMA / SHARPNESS / SHADING / PED.LV
IMAGE
BACK LIGHT / CONTRAST / POSI/NEGA / H-MIRROR /
PRIVACY
DNR
LOW / MIDDLE / HIGH / OFF
MOTION
ON / OFF
SYSTEM
CAM TITLE / CAM ID / ID DISP / SYNC / BAUDRATE /
LANGUAGE / SPECIAL
EXIT
SAVE / MANUAL / INITIAL / RESTORE
How to use OSD button(Tact Switch) in OSD control board or OSD cable
Press : enter into OSD menu and save settings at EXIT.
Push UP / DOWN : select function wish to activate.
Push LEFT / RIGHT : adjust level / value and mode of sub-menu
OSD Main Menu

VTC-BRE24F / VTC-IRE24F
5
MAIN MENU
DEFAULT
DESCRIPTION
EXPOSURE
Select Lens type according to mounted
/ built-in lens.
* ELC : Electronical Iris Lens
(Manual Iris Lens / Fixed Focal Lens).
* ALC: Auto Iris Lens(DC)
DAY&NIGHT
* AUTO: DAY or NIGHT is decided
automatically by light level coming through
lens.
* DAY: Color video output
* NIGHT: B/W video output regardless of
light level
* EXT: Day(Color) or Night(B/W) is decided by
external light sensor or LED control board
All IR LED cameras should set EXT.
* CDS: Not used
WHITE BAL
ATW
* ATW (Auto Tracking White Balance)
* MANUAL: Adjust White Balance with
fixed values of BLUE and RED
* PUSH: White Balance is performed when
enter button of OSD is pressed
MONITOR
* Set GAMMA, CHROMA, SHARPNESS,
SHADING & PED. LEVEL of Monitor
IMAGE
* BACK LIGH: Select HLC or BLC and adjust it.
* Select CONTRAST ON or OFF
* POSI / NEGA: Select Posi or Nega image.
* H-MIRROR: Select MIRROR ON or OFF
* PRIVACY: Set PRIVACY ON or OFF
DNR
OFF
Set DNR level, LOW or MIDDLE or HIGH
MOTION
OFF
Select MOTION ON or OFF
SYSTEM
Set CAM TITLE, CAM ID, ID DISP, SYNC,
BAUDRATE, LANGUAGE and SPECIAL
EXIT
SAVE, MANUAL, INITIAL, RESTORE

VTC-BRE24F / VTC-IRE24F
6
1. EXPOSURE
Select lens type in accordance with mounted/built-in lens.
* ALC : Auto Iris Lens
* ELC : Electronic Iris Lens
(Fixed Focal Lens / Manual Iris Vari-focal Lens)
EXPOSURE
(ALC / ELC)
DEFAULT
DESCRIPTION
BRIGHTNESS
Adjust the brightness level of screen when the
environment is extremely bright or dark.
SHUTTER
AUTO
Adjustable shutter speed. This is useful when
the light condition is changing quickly
* Set AUTO, 1/50 ~ 1/120K
FLK
OFF
Select FLICKERLESS ON or OFF. In the FLK
ON, sensitivity will be reduced under low light
AGC
20
Setting AGC level, 0 ~ 20. The higher gain
level, brighter picture with more noise.
2. DAY & NIGHT
DAY &
NIGHT
DEFAULT
DESCRIPTION
DAY &
NIGHT
IR LED
CAMERA : EXT
NONE IR
CAMERA :
AUTO
* AUTO: Camera decide DAY or NIGHT by
himself through incoming light level.
ICR is also moving DAY or NIGHT (ICR
Version).
* DAY: Camera works as a regular color
camera.
ICR is inserted to cut IR spectrum from light
(ICR built-in Camera)

VTC-BRE24F / VTC-IRE24F
7
DAY &
NIGHT
DEFAULT
DESCRIPTION
DAY &
NIGHT
* NIGHT: Camera works as a regular B/W camera.
ICR move to pass IR spectrum.
* CDS : Not used
* EXT : DAY or NIGHT is decided by external
signal(included CDS sensor) built in camera.
All of IR LED Cameras must be set to EXT.
2-1. AUTO
Usually cameras with no IR LED is set AUTO. But IR LED cameras should set
EXT.
AUTO
DEFAULT
DESCRIPTION
AGC THRS
11
* Setting threshold level to switch from to DAY <-->
NIGHT.
AGC
MARGIN
* Setting threshold margin to switch from to DAY
<--> NIGHT.
* If AGC margin is too small, may occur switching
D <--> N repeatly. Recommend more than 10
D/N DELAY
3SEC
* Dwell time before switch D <--> N after check
light level. * DELAY can avoid unnecessary
switching by short term light.
* To make right switch D <--> N, camera should
retain the present environment for longer than
DELAY(DWELL TIME).
B/W BURST
OFF
* Select BURST ON or OFF
SMART IR
* Not used (Camera with no IR LED set Auto and
no need SMART IR)

VTC-BRE24F / VTC-IRE24F
8