Vitek VTC-IRM5H-2713 User manual

FEATURES:
• 1/2.8” 2 MegaPixel Sony® STARVIS CMOS Sensor
• 2 MegaPixel Coax Based Camera (1920 × 1080 @ 30/25fps)
• 5 × 850nm High power LEDs with up to 130’ IR Range
• Video output EX-SDI1.0,2.0 / HD-SDI / TVI mode / AHD mode / CVI mode
or CVBS Selectable
• f=2.7~13.5mm F 1.6, 5 MegaPixel Motorized Zoom Lens [VTC-IRM5H-2713]
• f=5.0~50mm F 1.6, 5 MegaPixel Motorized Zoom Lens [VTC-IRM5H-550]
• Automatically Removable IR Cut Filter with Dual Filter Switch
• True WDR (Wide Dynamic Range) @30/25fps
• ROI (Region of Interest) WDR
• Improved Noise Reduction with XD-DNR
• Motion Detection, Privacy Mask, DeFog, Sens-up(~x32), ROI-WDR, D-WDR,
Sharpness, DeBlur, Mirror / Flip, Backlight / Highlight Compensation, Smart IR,
Anti-Saturation, Title Set
• OSD Menu & Video Sub-out for Easy Installation and Maintenance
• 1500’ HD-Analog Transmission Distance over Coax (Depending on Cable
Characteristics and Integrity)
• COC [Control over Coax] Through HD-TVI (Pelco-C®) or AHD
• One-Touch 3-Axis Locking Bracket, Easy Installation Pad
• AC24V/DC12V
• IP68, Aluminum Cast, Dual window, One-Touch 3-Axis Locking Bracket, Easy
Installation Pad
• 3-Year Warranty
VTC-IRM5H-2713
VTC-IRM5H-550
Virtuoso Series 2 MegaPixel
Multi-Format Auto Focus
WDR Bullet Camera
QUICK START GUIDE
VITEK
VITEK
COAX

Safety Precaution
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFERSERVICING TO QUALIFIEDSERVICE PERSONNEL.
To prevent electric shocks and risk of fire hazards, do NOT use other than
specific power source.
The symbol is intended to alert the user to the presence of important
operating and maintenance(servicing) instructions in the literature
accompanying the unit.
The symbol is intended to alert the user tothe presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
Warning :
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely tocause harmful
interference in which case the user will be required tocorrect the interference at
his own expense.
Caution :
Any changes or modifications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user's authority
to operate the equipment.
Mains power quality should be that of atypical commercial environment. If the user
of the model requires continued operation during power mains interruptions, it is
recommended that the model be powered from an uninterruptible power supply
(UPS) or a battery.
2 3

Safety Precaution
NOTICE
The images used in this instruction manual are processed to help comprehension
and may differ from actual video of the camera.
Avoid installing areas where has shock or vibration which results in the problems.
Pay attention to safety when laying the connection cable and observe that the cable
is not subjected to heavy loads, kinks or damage and no moisture can get in.
The warranty becomes void if repairs are undertaken by unauthorized persons.
Maintenance and repair have to be carried out only by authorized service centers.
Use only a mild detergent to clean the housing.
The camera should never be operated beyond the technical specifications.
This can lead to destruction.
The camera should never be operated in water.
3

Composition
Dimensions
Video Sub-out
Cable (1pc)
Mounting
Template
Operating
Instruction
Torque Wrench:
3mm (1pc)
Camera
Easy
Bracket
Mounting Screw:
4 x 30mm (4pcs)
Plastic Anchor:
6 x 30mm (4pcs)
Assembly Screw:
4 x 15mm (4pcs)
10.51” / 267mm
4.26” / 108mm
3.44” / 87.30mm
3.94” / 100mm
3.41” / 86.40mm
2.99” / 75.90mm
3.15” / 80mm
7.48” / 190mm
4 5

Part Names
Adjustment of viewing angle with a bracket
Torque
wrench
Lock/Unlock
Screw
•Extreme care should be taken NOT to
scratch the window in front of lens.
•Care should be taken the cable is NOT
to be damaged, kinked or exposed in
the hazardous area.
• Do not expose the camera directly to
a strong light source such as the sun
or spot light.
CAUTION
Power/Video
Cable
Sunshield
Sunshield Bold
Easy
Bracket
OSD Setup
Control Cover
Bracket
Lock/Unlock
Screw
5

Installation Instructions
Torque Wrench
Assembly Screw
: 4x15mm
Mounting Screw
: 4x30mm
1. Locate the mounting template at the installation position and drill the ceiling or
wall if needed. ( *The easy bracket can not be installed on the ceiling)
2. Place the easy bracket on pre-drilled position and fix it through using mounting
screws (4x30mm). Skip this step when an easy bracket is not installed.
3. Route the Power cable to the connecting place.
Hook up the camera bracket with the easy bracket as illustrated below.
4. Fix the camera bracket through using assembly screws (4x15mm).
5. Set the camera’s viewing angle.
6. Put the sunshield to the camera unit and tighten the sunshield-bolts.
REAR VIEW
1
2
3
4
Cable exit
6 7

Installation Instructions
Pan & Tilt adjustments
1) Pan limit:
Pan is limited to +/- 90°.
3) Inclination limit
(Horizontal image alignment):
Inclination limited to +/-90° max.
2) Tilt limit:
Tilt is limited to 0°(2°) min ~ 90° max.
for wall(ceiling) installation respectively
with reference to the wall(ceiling) when
the inclination of camera module is 0°,
that is, the image is aligned horizontally.
90° 90°
• Unlock the screw on the camera bracket through using the torque wrench supplied
• Set the camera’s viewing angle then lock the screw on the bracket.
88°90°
±90°
•on the wall • on the ceiling
7

Installation Instructions
Installation and commissioning Instructions
• Make sure the power is removed before the installation.
• Follow the order for applying power.
First, connect the low voltage (AC24V or DC12V), then plug the AC adapter to
AC outlets to avoid an improper reset from power jitter and a damage from the
surge voltage when no load.
Power Supply Connections
Camera can work with either AC24V or DC12V, dual voltage power. Primary
and secondary grounds are completely isolated to avoid the possible ground-loop
problems
※SDI OUTPUT
(Yellow)
ANALOG OUTPUT
(Black)
POWER
(AC24V/DC12V)
AC(-) :
AC24V/GND
AC(+) :
AC24V/DC12V
AC
(+)
AC
(-)
※Please use the cable as provided with camera. If camera cable is cut
and re-wired, the transmission distance of video can be reduced.
Especially SDI cable should not be cut because it requires detailed
wiring job and affects the transmission distance.
8 9

NOTES
9

DETAILED SPECIFICATIONS
Imaging Sensor 1/2.8” 2 MegaPixel Sony STARVIS CMOS® Sensor
Effective Pixels 1920(H) x 1080(V) x 30p
Scan Frequency 30Hz(V), 22.5Khz(H) Progressive
Video Format HD: 16:9, 1080p@30fps / CVBS: 16:9 (NTSC)
Video Output Digital: EX-SDI 1.0/ 2.0/ 2.1, HD-SDI, HD-Analog: TVI mode, AHD mode, SD-Analog: CVBS
Synchronization Internal
Min. Illumination Color: 0.08 Lux, B/W: 0.005 Lux (LED Off)
S/N Ratio More than 50dB (AGC Off)
Lens VTC-IR5H-2713 f=2.7~13.5mm F 1.6, 5MP Mtrzd Zoom Lens, VTC-IR5H-550 f=5.0~50mm F 1.6, 5MP Mtrzd Zoom Lens
IR LEDs / Range 5pcs x 850nm High power LEDs - 150’
Exposure Brightness / Shutter / Sens-up / AGC
Focus Auto / Zoom Push / Manual
Day / Night True Day / Night by dual filter switch, EXT / AUTO / COLOR / B&W
White Balance AUTO / AUTOext / MANUAL / PRESET
WDR True WDR by Dual Scan Images at 30fps/25fps
ROI WDR YES
DNR XD-DNR (2D-DNR / 3D-DNR)
D-Zoom N/A
Image Orientation Mirror / Flip / Rotate / Normal
Special Features POI (Point Of Interest) Zoom, Smart Motion Zoom, Preset Zoom, Home Position
Functions ROI-WDR, D-WDR, Motion Detection, Privacy Mask, Defog, Sens-up(~x32), Sharpness, Mirror/Flip, BLC/HLC,
Ingress Protection IP-68 Weather Resistance Rating
Remote Control COC by HD-TVI (Pelco-C®) or AHD
OSD Language English, Korean, Japanese, Chinese, German
Video Output VBS 1Vp-p ± 10%, 75Ω
Installation Temp. -4°F~122°F (-20°C ~ +50°C)
Installation Humidity 20%RH ~ 80%RH
Operating Temp. -22°F~122°F (-30°C ~ +50°C)
Operating Humidity 20%RH ~ 80%RH
Power Input AC24V/DC12V
Power Consumption (12VDC) 370mA (IR Off) / 750mA (IR On)
Power Consumption (24VAC) 185mA (IR Off) / 375mA (IR On)
Power Features Circuit protection against faulty connection in power polarity, and isolated power supply protects against ground
Housing Aluminum Cast, Dual window, One-Touch 3-Axis Locking Bracket, Easy Installation Pad
Dimensions 4.25” W x 3.94 H x 10.51 L (108 x 100 x 267mm)
Weight (w/ Bracket) 2.98lbs (1.35kg)
10 11

11
FOR FULL OPERATION AND SETUP
INSTRUCTIONS PLEASE REFER TO THE
COMPLETE MANUAL BY SCANNING
THE QR CODE BELOW:

12 PB
LIMITED PRODUCT WARRANTY
VITEK products carry a three (3) year limited warranty. VITEK warrants to the
purchaser that products manufactured by VITEK are free of any rightful claim
of infringement or the like, and when used in the manner intended, will be
free of defects in materials and workmanship for a period of three (3) years,
or as otherwise stated above, from the date of purchase by the end user.
This warranty is nontransferable and extends only to the original buyer or end
user customer of a VITEK Authorized Reseller.
The product must have been used only for its intended purpose, and not
been subjected to damage by misuse, willful or accidental damage, caused
by excessive voltage or lightning.
The product must not have been tampered with in any way or the guarantee
will be considered null and void.
This guarantee does not affect your statutory rights.
Contact your local VITEK Reseller should servicing become necessary.
VITEK makes no warranty or guarantee whatsoever with respect to products
sold or purchased through unauthorized sales channels. Warranty support is
available only if product is purchased through a VITEK Authorized Reseller.
28492 CONSTELLATION ROAD VALENCIA, CA 91355
WWW.VITEKCCTV.COM
Version 1.0
June 2022