VIV STAND-TV03N User manual

Black TV Floor Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-tv03n
SKU: STAND-TV03N
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF TV OR TV CART.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
PACKAGE CONTENTS
1 (x1)
Le Base
2(x1)
Right Base
3(x1)
Base
Connector
10(x2)
Plate Connector
and Plastic Shim
11 x20)
M6x10
12 (x1)
Tool Kit
8(x2)
RubberFoot
4 (x2)
Base Pole
5 (x2)
Top Pole
6 (x2)
Pole Connector
7 (x4)
Pole
Cover
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
14 (x2)
Shelf Support
13 (x1)
Shelf
15 x4)
M4x6
19 (x4)
M6x20
M6x35
18 (x4)
M4x12
M4x30
17 (x1)
VESA Bracket
Set
22 (x4)
M4 Washer
23 (x14)
M6 Washer
25 (x4)
M8 Washer
16 x1)
Mounting
Plate
27 (x8)
M6/8 Spacer
(5mm)
20 (x4)
M8x20
M8x35
M8x45
26 (x4)
M4 Spacer
M6/8 Spacer
(20mm)
9 x2)
Support Feet
and Pads
21 x2)
M6x29
24 x2)
Silver M6
washer
M4
Phillips
M2.5
28 (x2)
M6 Nut

3
ASSEMBLY STEPS
STEP 1
TOOLS NEEDED
Phillips
Screwdriver
Attach le and right base (1, 2) to the base connector (3) using M6x10 bolts (11).
Tighten with the 4mm Allen wrench (12).
STEP 2
Assemble both of the Support Feet and Pads (9) using the M6x29 bolt (21), M6 washer
(23), and nut (28). Tighten using the Wrench (12). Spin both of these onto the Base
Connector (3) by hand while using the washer (24). When the Support Feet (9) are fully
seated, loosen it no more than a full turn to position them so they face backwards as
shown below. Then spin on the Rubber feet (8) onto the Right and Le Base (1,2).
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
110 lbs
(49.9 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury. 10 lbs
(4.54 kg)
CART SHELF
10
3
2
1
12
x1
M4
12
x1
11
21
9
23 28
12
2x
12
8
24
3
21
9

4
STEP 3
Thread the pole connectors (6)
onto the base poles (4), making
sure the connectors thread
in straight to avoid cross-
threading. Use caution when
threading pole connectors.
Threads are very fine and may
have sharp edges.
STEP 5
Thread the Top Poles (5) to the Pole Connectors
(6) and insert the Pole Covers (7) into the top.
Slide the Plate Connector and Plastic
Shims (10) over the Top Poles (5)
and tighten the set screw in each
connector using the 4mm Allen
wrench (12).
STEP 4
Attach the base poles (4) to the
assembled base using M6x10 bolts
(11) and 4mm Allen wrench (12).
12
x1
M4
STEP 6
12
x1
M4
5
7
6
4
4
11
12
6
5
9
12
10

5
STEP 7
Attach the Mounting plate (16) to the Plate Connectors (10) with M6x10 bolts (11) and M6 washers (23)
using the 4mm Allen wrench (12).
Note: Loosly insert all bolts before fully tightening.
Clip the bubble level (12) onto the Mounting Plate (16). Adjust the level of the Mounting Plate (16)
by loosening the set screw in the back of the Plate Connector (10) using the 4mm Allen wrench (12).
Tighten set screws again once you’ve reached desired height and level.
STEP 8
12
x1
M4
12
x1
12
x1
M4 Bubble Level
16
10
22
t
Attach bubble level
o the wall plate
12
11
23
12
16
10
16
Attach bubble level to
Mounting Plate